diff options
Diffstat (limited to 'Documentation/diff-options.txt')
| -rw-r--r-- | Documentation/diff-options.txt | 83 |
1 files changed, 62 insertions, 21 deletions
diff --git a/Documentation/diff-options.txt b/Documentation/diff-options.txt index f6c046a09a..4235302ea4 100644 --- a/Documentation/diff-options.txt +++ b/Documentation/diff-options.txt @@ -72,19 +72,49 @@ These parameters can also be set individually with `--stat-width=<width>`, number of modified files, as well as number of added and deleted lines. ---dirstat[=<limit>]:: - Output the distribution of relative amount of changes (number of lines added or - removed) for each sub-directory. Directories with changes below - a cut-off percent (3% by default) are not shown. The cut-off percent - can be set with `--dirstat=<limit>`. Changes in a child directory are not - counted for the parent directory, unless `--cumulative` is used. +--dirstat[=<param1,param2,...>]:: + Output the distribution of relative amount of changes for each + sub-directory. The behavior of `--dirstat` can be customized by + passing it a comma separated list of parameters. + The defaults are controlled by the `diff.dirstat` configuration + variable (see linkgit:git-config[1]). + The following parameters are available: + -Note that the `--dirstat` option computes the changes while ignoring -the amount of pure code movements within a file. In other words, -rearranging lines in a file is not counted as much as other changes. - ---dirstat-by-file[=<limit>]:: - Same as `--dirstat`, but counts changed files instead of lines. +-- +`changes`;; + Compute the dirstat numbers by counting the lines that have been + removed from the source, or added to the destination. This ignores + the amount of pure code movements within a file. In other words, + rearranging lines in a file is not counted as much as other changes. + This is the default behavior when no parameter is given. +`lines`;; + Compute the dirstat numbers by doing the regular line-based diff + analysis, and summing the removed/added line counts. (For binary + files, count 64-byte chunks instead, since binary files have no + natural concept of lines). This is a more expensive `--dirstat` + behavior than the `changes` behavior, but it does count rearranged + lines within a file as much as other changes. The resulting output + is consistent with what you get from the other `--*stat` options. +`files`;; + Compute the dirstat numbers by counting the number of files changed. + Each changed file counts equally in the dirstat analysis. This is + the computationally cheapest `--dirstat` behavior, since it does + not have to look at the file contents at all. +`cumulative`;; + Count changes in a child directory for the parent directory as well. + Note that when using `cumulative`, the sum of the percentages + reported may exceed 100%. The default (non-cumulative) behavior can + be specified with the `noncumulative` parameter. +<limit>;; + An integer parameter specifies a cut-off percent (3% by default). + Directories contributing less than this percentage of the changes + are not shown in the output. +-- ++ +Example: The following will count changed files, while ignoring +directories with less than 10% of the total amount of changed files, +and accumulating child directory counts in the parent directories: +`--dirstat=files,10,cumulative`. --summary:: Output a condensed summary of extended header information @@ -130,12 +160,19 @@ any of those replacements occurred. --color[=<when>]:: Show colored diff. - The value must be always (the default), never, or auto. + The value must be `always` (the default for `<when>`), `never`, or `auto`. + The default value is `never`. +ifdef::git-diff[] + It can be changed by the `color.ui` and `color.diff` + configuration settings. +endif::git-diff[] --no-color:: - Turn off colored diff, even when the configuration file - gives the default to color output. - Same as `--color=never`. + Turn off colored diff. +ifdef::git-diff[] + This can be used to override configuration settings. +endif::git-diff[] + It is the same as `--color=never`. --word-diff[=<mode>]:: Show a word diff, using the <mode> to delimit changed words. @@ -193,10 +230,14 @@ endif::git-format-patch[] ifndef::git-format-patch[] --check:: - Warn if changes introduce trailing whitespace - or an indent that uses a space before a tab. Exits with - non-zero status if problems are found. Not compatible with - --exit-code. + Warn if changes introduce whitespace errors. What are + considered whitespace errors is controlled by `core.whitespace` + configuration. By default, trailing whitespaces (including + lines that solely consist of whitespaces) and a space character + that is immediately followed by a tab character inside the + initial indent of the line are considered whitespace errors. + Exits with non-zero status if problems are found. Not compatible + with --exit-code. endif::git-format-patch[] --full-index:: @@ -249,7 +290,7 @@ ifdef::git-log[] For following files across renames while traversing history, see `--follow`. endif::git-log[] - If `n` is specified, it is a is a threshold on the similarity + If `n` is specified, it is a threshold on the similarity index (i.e. amount of addition/deletions compared to the file's size). For example, `-M90%` means git should consider a delete/add pair to be a rename if more than 90% of the file |