config: Create printer-biqu-b1-se-plus.cfg (#5477)

Signed-off-by: Bruno Melo <brunomelo81@gmail.com>

1 files changed, 198 insertions, 0 deletions

diff --git a/config/printer-biqu-b1-se-plus-2022.cfg b/config/printer-biqu-b1-se-plus-2022.cfg
new file mode 100644
index 000000000..e5b3af520
--- /dev/null
+++ b/config/printer-biqu-b1-se-plus-2022.cfg
@@ -0,0 +1,198 @@
+# This file contains common pin mappings for the Biqu B1 SE Plus.
+# To use this config, the firmware should be compiled for the
+# STM32F407 with a "32KiB bootloader".
+
+# In newer versions of this board shipped in late 2021 the STM32F429
+# is used, if this is the case compile for this with a "32KiB bootloader"
+# You will need to check the chip on your board to identify which you have.
+#
+# The "make flash" command does not work on the SKR 2. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "firmware.bin" on an SD card and then restart the SKR 2
+# with that SD card.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_1D0039000F47393438343535-if00
+
+########################################
+# Stepper X Pins and TMC2208 configuration
+########################################
+[stepper_x]
+step_pin: PE2
+dir_pin: !PE1
+enable_pin: !PE3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PC1
+position_endstop: 0
+position_max: 310
+homing_speed: 50
+
+[tmc2208 stepper_x]
+uart_pin: PE0
+run_current: 0.800
+stealthchop_threshold: 999999
+
+########################################
+# Stepper Y Pins and TMC2208 configuration
+########################################
+[stepper_y]
+step_pin: PD5
+dir_pin: PD4
+enable_pin: !PD6
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PC3
+position_endstop: 0
+position_max: 310
+homing_speed: 50
+
+[tmc2208 stepper_y]
+uart_pin: PD3
+run_current: 0.800
+stealthchop_threshold: 999999
+
+########################################
+# Stepper Z Pins and TMC2208 configuration
+########################################
+[stepper_z]
+step_pin: PA15
+dir_pin: PA8
+enable_pin: !PD1
+microsteps: 16
+rotation_distance: 8
+endstop_pin: probe:z_virtual_endstop
+homing_speed: 10
+second_homing_speed: 1
+position_min: -2
+position_max: 340
+
+[tmc2208 stepper_z]
+uart_pin: PD0
+run_current: 0.800
+stealthchop_threshold: 999999
+
+########################################
+# Extruder Pins and TMC2208 configuration
+########################################
+[extruder]
+step_pin: PD15
+dir_pin: !PD14
+enable_pin: !PC7
+microsteps: 16
+rotation_distance: 34.2152 # Calibrar - ver https://www.klipper3d.org/Rotation_Distance.html
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB3
+sensor_type: Generic 3950
+sensor_pin: PA2 #thermistor pin
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+[tmc2208 extruder]
+uart_pin: PC6
+run_current: 0.800
+stealthchop_threshold: 999999
+########################################
+
+########################################
+# Heater Bed Pins
+########################################
+[heater_bed]
+heater_pin: PD7
+sensor_type: Generic 3950
+sensor_pin: PA1
+control: pid
+pid_Kp: 54
+pid_Ki: 0.77
+pid_Kd: 900
+min_temp: 0
+max_temp: 110
+
+########################################
+# Printer Configuration
+########################################
+[printer]
+kinematics: cartesian
+max_velocity: 200
+max_accel: 1000
+max_z_velocity: 5
+max_z_accel: 100
+
+########################################
+# Probe configuration
+########################################
+[probe]
+pin: ^!PE4
+z_offset: 0.0
+x_offset: 0.0
+y_offset: 0.0
+speed: 10.0
+samples: 2
+samples_result: average
+sample_retract_dist: 2.0
+samples_tolerance: 0.2
+
+[safe_z_home]
+home_xy_position: 155,155
+speed: 100
+z_hop: 5
+z_hop_speed: 5
+
+[output_pin probe_enable]
+pin: PE5
+value: 1
+
+########################################
+# Bed Mesh configuration               # exemple off bed mesh config
+########################################
+[bed_mesh]
+speed: 2000
+horizontal_move_z: 3
+mesh_min: 20, 20
+mesh_max: 290, 290
+probe_count: 7, 7
+mesh_pps: 2,2
+algorithm: bicubic
+bicubic_tension: 0.2
+
+########################################
+# Fan Nozzle configuration
+########################################
+[fan]
+pin: PB7
+
+[heater_fan Cooling_fan]
+pin: PB6
+max_power: 1.0
+kick_start_time: 0.100
+heater: heater_bed
+
+[heater_fan Board_fan]
+pin: PB5
+max_power: 1.0
+kick_start_time: 0.100
+heater: extruder
+########################################
+
+########################################
+# Filament Sensor configuration
+########################################
+[filament_switch_sensor Sensor_Filamento]
+switch_pin: !PC2
+pause_on_runout: true #pause handled by macro
+
+########################################
+
+########################################
+# Motor Power Pin
+########################################
+[output_pin motor_power]
+pin: PC13
+value: 1