Start code revisions

During a supplementary review, the start codes were found to be mislabeled. This has been corrected.

6 files changed, 6 insertions, 6 deletions

diff --git a/resources/definitions/tronxy_d01.def.json b/resources/definitions/tronxy_d01.def.json
index 141414f85f..6a752656f7 100644
--- a/resources/definitions/tronxy_d01.def.json
+++ b/resources/definitions/tronxy_d01.def.json
@@ -21,7 +21,7 @@
         },
         "gantry_height": { "value": 30 },
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21\nG90\nM82\nM107 T0\nM140 S{material_bed_temperature_layer_0}\nM104 S{material_print_temperature_layer_0} T0\nM190 S{material_bed_temperature_layer_0}\nM109 S{material_print_temperature_layer_0} T0\nG28\nG92 E0\nG1 Z2.0 F3000 ; Move Z Axis up little to preventscratching of Heat Bed\nG1 X1 Y20 Z0.3 F3600.0 ; Move to start position\nG1 X1 Y220.0 Z0.3 F1500.0 E25 ; Draw the first line\nG1 X1.6 Y220.0 Z0.3 F3600.0 ; Move to side a little\nG1 X1.6 Y20 Z0.3 F1500.0 E50 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.3 F3600.0 ; Move over to prevent blob squish" },
+        "machine_start_gcode": { "default_value": "; D01 Start Code\nG21\nG90\nM82\nM107 T0\nM140 S{material_bed_temperature_layer_0}\nM104 S{material_print_temperature_layer_0} T0\nM190 S{material_bed_temperature_layer_0}\nM109 S{material_print_temperature_layer_0} T0\nG28\nG92 E0\nG1 Z2.0 F3000 ; Move Z Axis up little to preventscratching of Heat Bed\nG1 X1 Y20 Z0.3 F3600.0 ; Move to start position\nG1 X1 Y200.0 Z0.3 F1500.0 E25 ; Draw the first line\nG1 X1.6 Y200.0 Z0.3 F3600.0 ; Move to side a little\nG1 X1.6 Y20 Z0.3 F1500.0 E50 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.3 F3600.0 ; Move over to prevent blob squish" },
         "machine_end_gcode": { "default_value": "M83 ; Set extrder to Relative\nG1 E-5 F3000 ; Retract 5mm of filament at 50mm/s\nG90 ; Set all axis to Absolute \nG1 X0 Y{machine_depth} ; Park print head\nG1 Z10 ; Move up 10mm\nM106 S0 ; Set fan speed to 0\nM104 S0 ; Set bed temp to 0\nM140 S0 ; Set Nozzle temp to 0\nM84 ; Disable all stepper motors\n" },
 
         "machine_acceleration": { "value": 120 }
diff --git a/resources/definitions/tronxy_x5sa.def.json b/resources/definitions/tronxy_x5sa.def.json
index a4ca9a510a..ba0b9a92e0 100644
--- a/resources/definitions/tronxy_x5sa.def.json
+++ b/resources/definitions/tronxy_x5sa.def.json
@@ -22,7 +22,7 @@
         "gantry_height": { "value": 40 },
         "retraction_amount": { "value": 4.5 },
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_start_gcode": { "default_value": "; X5SA Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
         "machine_end_gcode": { "default_value": "G91 ; Set Positioning to Relative\nM83 ; Set Extruder to Relative\nG92 E0 ; Reset Extruder\nG1 E-4 F3000 ; Retract 4mm of filament\nG1 Z0.2 ; Raise nozzle .2mm\nG90 ; Set positioning to absolute\nG1 X{machine_width} Y{machine_depth} ; Park print head\nG91 ; Set Positioning to RelativeG1 Z10 ; Raise nozzle 10mm\nM106 S0 ; Turn off part fan\nM104 S0 ; Set nozzle temp to zero\nM140 S0 ; set bed temp to zero\nM84 X Y Z E ; Disable X Y Z and E steppers\n" },
 
         "machine_acceleration": { "value": 150 }
diff --git a/resources/definitions/tronxy_xy2.def.json b/resources/definitions/tronxy_xy2.def.json
index ce7966fc3b..7894141b9d 100644
--- a/resources/definitions/tronxy_xy2.def.json
+++ b/resources/definitions/tronxy_xy2.def.json
@@ -22,7 +22,7 @@
         "gantry_height": { "value": 40 },
         "retraction_amount": { "value": 4.5 },
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
         "machine_end_gcode": { "default_value": "M83 ; Set extrder to Relative\nG1 E-5 F3000 ; Retract 5mm of filament at 50mm/s\nG90 ; Set all axis to Absolute \nG1 X0 Y{machine_depth} ; Park print head\nG1 Z10 ; Move up 10mm\nM106 S0 ; Set fan speed to 0\nM104 S0 ; Set bed temp to 0\nM140 S0 ; Set Nozzle temp to 0\nM84 ; Disable all stepper motors\n" },
 
         "machine_acceleration": { "value": 150 }
diff --git a/resources/definitions/tronxy_xy2pro.def.json b/resources/definitions/tronxy_xy2pro.def.json
index fb2bd70ea3..ed16c34352 100644
--- a/resources/definitions/tronxy_xy2pro.def.json
+++ b/resources/definitions/tronxy_xy2pro.def.json
@@ -22,7 +22,7 @@
         "gantry_height": { "value": 40 },
         "retraction_amount": { "value": 4.5 },
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_start_gcode": { "default_value": "; XY-2 Pro Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
         "machine_end_gcode": { "default_value": "M83 ; Set extrder to Relative\nG1 E-5 F3000 ; Retract 5mm of filament at 50mm/s\nG90 ; Set all axis to Absolute \nG1 X0 Y{machine_depth} ; Park print head\nG1 Z10 ; Move up 10mm\nM106 S0 ; Set fan speed to 0\nM104 S0 ; Set bed temp to 0\nM140 S0 ; Set Nozzle temp to 0\nM84 ; Disable all stepper motors\n" },
 
         "machine_acceleration": { "value": 150 }
diff --git a/resources/definitions/tronxy_xy3.def.json b/resources/definitions/tronxy_xy3.def.json
index 941ca7142f..345def8926 100644
--- a/resources/definitions/tronxy_xy3.def.json
+++ b/resources/definitions/tronxy_xy3.def.json
@@ -22,7 +22,7 @@
         "gantry_height": { "value": 30 },
         "retraction_amount": { "value": 5 },
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_start_gcode": { "default_value": "; XY-3 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
         "machine_end_gcode": { "default_value": "M83 ; Set extrder to Relative\nG1 E-5 F3000 ; Retract 5mm of filament at 50mm/s\nG90 ; Set all axis to Absolute \nG1 X0 Y{machine_depth} ; Park print head\nG1 Z10 ; Move up 10mm\nM106 S0 ; Set fan speed to 0\nM104 S0 ; Set bed temp to 0\nM140 S0 ; Set Nozzle temp to 0\nM84 ; Disable all stepper motors\n" },
 
         "machine_acceleration": { "value": 150 }
diff --git a/resources/definitions/tronxy_xy3proV2.def.json b/resources/definitions/tronxy_xy3proV2.def.json
index 2be9a1998e..841c159375 100644
--- a/resources/definitions/tronxy_xy3proV2.def.json
+++ b/resources/definitions/tronxy_xy3proV2.def.json
@@ -24,7 +24,7 @@
         "retraction_speed": { "value": 45 },
 
 
-        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_start_gcode": { "default_value": "; XY-3 Pro Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
         "machine_end_gcode": { "default_value": "M83 ; Set extrder to Relative\nG1 E-5 F3000 ; Retract 5mm of filament at 50mm/s\nG90 ; Set all axis to Absolute \nG1 X0 Y{machine_depth} ; Park print head\nG1 Z10 ; Move up 10mm\nM106 S0 ; Set fan speed to 0\nM104 S0 ; Set bed temp to 0\nM140 S0 ; Set Nozzle temp to 0\nM84 ; Disable all stepper motors\n" },
 
         "machine_acceleration": { "value": 150 }