Removed settings subobject in overrides

CURA-1278

1 files changed, 75 insertions, 77 deletions

diff --git a/resources/definitions/bq_hephestos.def.json b/resources/definitions/bq_hephestos.def.json
index 3b5b68c021..45bf520a14 100644
--- a/resources/definitions/bq_hephestos.def.json
+++ b/resources/definitions/bq_hephestos.def.json
@@ -13,83 +13,81 @@
     },
 
     "overrides": {
-        "settings": {
-            "machine_start_gcode": {
-                "default_value": "; -- START GCODE --\nG21                     ;set units to millimetres\nG90                     ;set to absolute positioning\nM106 S0                 ;set fan speed to zero (turned off)\nG28 X0 Y0               ;move to the X/Y origin (Home)\nG28 Z0                  ;move to the Z origin (Home)\nG1 Z15.0 F1200          ;move Z to position 15.0 mm\nG92 E0                  ;zero the extruded length\nG1 E20 F200             ;extrude 20mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F7200                ;set feedrate to 120 mm/sec\n; -- end of START GCODE --"
-            },
-            "machine_end_gcode": {
-                "default_value": "; -- END GCODE --\nM104 S0                 ;set extruder temperature to zero (turned off)\nG91                     ;set to relative positioning\nG1 E-20 F300            ;retract the filament a bit to release some of the pressure\nG1 Z10                  ;move extruder up 10 mm\nG90                     ;set to absolute positioning\nG1 X0 Y180 F1200        ;expose the platform\nM84                     ;turn off steppers\n; -- end of END GCODE --"
-            },
-            "machine_width": {
-                "value": 215
-            },
-            "machine_depth": {
-                "value": 210
-            },
-            "machine_height": {
-                "value": 180
-            },
-            "machine_heated_bed": {
-                "value": false
-            },
-            "machine_center_is_zero": {
-                "value": false
-            },
-            "machine_gcode_flavor": {
-                "value": "RepRap"
-            },
-            "machine_platform_offset": {
-                "value": [
-                    0,
-                    -82,
-                    0
-                ]
-            },
-            "layer_height": {
-                "value": 0.2
-            },
-            "layer_height_0": {
-                "value": 0.2
-            },
-            "wall_thickness": {
-                "value": 1.0
-            },
-            "top_bottom_thickness": {
-                "value": 1.0
-            },
-            "bottom_thickness": {
-                "value": 1.0
-            },
-            "material_print_temperature": {
-                "value": 220
-            },
-            "material_bed_temperature": {
-                "value": 0
-            },
-            "material_diameter": {
-                "value": 1.75
-            },
-            "speed_print": {
-                "value": 40.0
-            },
-            "speed_infill": {
-                "value": 40.0
-            },
-            "speed_wall": {
-                "value": 35.0
-            },
-            "speed_topbottom": {
-                "value": 35.0
-            },
-            "speed_travel": {
-                "value": 120.0
-            },
-            "speed_layer_0": {
-                "value": 20.0
-            },
-            "support_enable": {
-                "value": true
-            }
+        "machine_start_gcode": {
+            "default_value": "; -- START GCODE --\nG21                     ;set units to millimetres\nG90                     ;set to absolute positioning\nM106 S0                 ;set fan speed to zero (turned off)\nG28 X0 Y0               ;move to the X/Y origin (Home)\nG28 Z0                  ;move to the Z origin (Home)\nG1 Z15.0 F1200          ;move Z to position 15.0 mm\nG92 E0                  ;zero the extruded length\nG1 E20 F200             ;extrude 20mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F7200                ;set feedrate to 120 mm/sec\n; -- end of START GCODE --"
+        },
+        "machine_end_gcode": {
+            "default_value": "; -- END GCODE --\nM104 S0                 ;set extruder temperature to zero (turned off)\nG91                     ;set to relative positioning\nG1 E-20 F300            ;retract the filament a bit to release some of the pressure\nG1 Z10                  ;move extruder up 10 mm\nG90                     ;set to absolute positioning\nG1 X0 Y180 F1200        ;expose the platform\nM84                     ;turn off steppers\n; -- end of END GCODE --"
+        },
+        "machine_width": {
+            "value": 215
+        },
+        "machine_depth": {
+            "value": 210
+        },
+        "machine_height": {
+            "value": 180
+        },
+        "machine_heated_bed": {
+            "value": false
+        },
+        "machine_center_is_zero": {
+            "value": false
+        },
+        "machine_gcode_flavor": {
+            "value": "RepRap"
+        },
+        "machine_platform_offset": {
+            "value": [
+                0,
+                -82,
+                0
+            ]
+        },
+        "layer_height": {
+            "value": 0.2
+        },
+        "layer_height_0": {
+            "value": 0.2
+        },
+        "wall_thickness": {
+            "value": 1.0
+        },
+        "top_bottom_thickness": {
+            "value": 1.0
+        },
+        "bottom_thickness": {
+            "value": 1.0
+        },
+        "material_print_temperature": {
+            "value": 220
+        },
+        "material_bed_temperature": {
+            "value": 0
+        },
+        "material_diameter": {
+            "value": 1.75
+        },
+        "speed_print": {
+            "value": 40.0
+        },
+        "speed_infill": {
+            "value": 40.0
+        },
+        "speed_wall": {
+            "value": 35.0
+        },
+        "speed_topbottom": {
+            "value": 35.0
+        },
+        "speed_travel": {
+            "value": 120.0
+        },
+        "speed_layer_0": {
+            "value": 20.0
+        },
+        "support_enable": {
+            "value": true
         }
     }
 }
\ No newline at end of file