Update existing profiles

The Tronxy community has requested the removal of "max feedrate" settings in the slicer profile. The machines are usually run on one of three firmwares and these limitations really hinder slicer performance.

1 files changed, 6 insertions, 4 deletions

diff --git a/resources/definitions/tronxy_x5sa.def.json b/resources/definitions/tronxy_x5sa.def.json
index 0e70dd72b4..a4ca9a510a 100644
--- a/resources/definitions/tronxy_x5sa.def.json
+++ b/resources/definitions/tronxy_x5sa.def.json
@@ -1,11 +1,10 @@
 {
-    "name": "Tronxy X5SA/X5ST/Pro",
+    "name": "Tronxy X5SA/X5ST/Pro/2E/D01 Plus",
     "version": 2,
     "inherits": "tronxy_x",
     "metadata": {
         "quality_definition": "tronxy_x",
         "visible": true,
-        "author": "AdderMk2",
         "platform": "tronxy.stl"
     },
     "overrides": {
@@ -21,8 +20,11 @@
             ]
         },
         "gantry_height": { "value": 40 },
+        "retraction_amount": { "value": 4.5 },
 
-        "machine_start_gcode": { "default_value": "; X5SA Pro Start Code\nG21\nG90\nM82\nM107 T0\nM140 S{material_bed_temperature_layer_0}\nM104 S{material_print_temperature_layer_0} T0\nM190 S{material_bed_temperature_layer_0}\nM109 S{material_print_temperature_layer_0} T0\nG28\nG92 E0\n"},
-        "machine_end_gcode": { "default_value": "G91\nG1 E-2 F3000\nG1 E-2 Z0.2 F1200\nG1 X5 Y5 F3600\nG1 Z10\nG90\nG1 X0 Y0\nM106 S0\nM104 S0\nM140 S0\n\nM84 X Y E\n" }
+        "machine_start_gcode": { "default_value": "; XY-2 Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y220 F1500.0 E10 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E20 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"},
+        "machine_end_gcode": { "default_value": "G91 ; Set Positioning to Relative\nM83 ; Set Extruder to Relative\nG92 E0 ; Reset Extruder\nG1 E-4 F3000 ; Retract 4mm of filament\nG1 Z0.2 ; Raise nozzle .2mm\nG90 ; Set positioning to absolute\nG1 X{machine_width} Y{machine_depth} ; Park print head\nG91 ; Set Positioning to RelativeG1 Z10 ; Raise nozzle 10mm\nM106 S0 ; Turn off part fan\nM104 S0 ; Set nozzle temp to zero\nM140 S0 ; set bed temp to zero\nM84 X Y Z E ; Disable X Y Z and E steppers\n" },
+
+        "machine_acceleration": { "value": 150 }
     }
 }