Update translation templates

These are generated from the state of the code at commit b67b41653fc7c24061103993016fb29b86a51488.

Contributes to issue CURA-3487.

1 files changed, 175 insertions, 6 deletions

diff --git a/resources/i18n/fdmprinter.def.json.pot b/resources/i18n/fdmprinter.def.json.pot
index a4e29bad33..dcfd7c2e59 100644
--- a/resources/i18n/fdmprinter.def.json.pot
+++ b/resources/i18n/fdmprinter.def.json.pot
@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Uranium json setting files\n"
 "Report-Msgid-Bugs-To: http://github.com/ultimaker/uranium\n"
-"POT-Creation-Date: 2016-12-28 10:51+0000\n"
+"POT-Creation-Date: 2017-03-27 17:27+0000\n"
 "PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
 "Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
 "Language-Team: LANGUAGE\n"
@@ -269,6 +269,18 @@ msgid ""
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "machine_nozzle_temp_enabled label"
+msgid "Enable Nozzle Temperature Control"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "machine_nozzle_temp_enabled description"
+msgid ""
+"Whether to control temperature from Cura. Turn this off to control nozzle "
+"temperature from outside of Cura."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "machine_nozzle_heat_up_speed label"
 msgid "Heat up speed"
 msgstr ""
@@ -857,6 +869,47 @@ msgid "Zig Zag"
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "top_bottom_pattern_0 label"
+msgid "Bottom Pattern Initial Layer"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "top_bottom_pattern_0 description"
+msgid "The pattern on the bottom of the print on the first layer."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "top_bottom_pattern_0 option lines"
+msgid "Lines"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "top_bottom_pattern_0 option concentric"
+msgid "Concentric"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "top_bottom_pattern_0 option zigzag"
+msgid "Zig Zag"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "skin_angles label"
+msgid "Top/Bottom Line Directions"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "skin_angles description"
+msgid ""
+"A list of integer line directions to use when the top/bottom layers use the "
+"lines or zig zag pattern. Elements from the list are used sequentially as "
+"the layers progress and when the end of the list is reached, it starts at "
+"the beginning again. The list items are separated by commas and the whole "
+"list is contained in square brackets. Default is an empty list which means "
+"use the traditional default angles (45 and 135 degrees)."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "wall_0_inset label"
 msgid "Outer Wall Inset"
 msgstr ""
@@ -1125,6 +1178,22 @@ msgid "Zig Zag"
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "infill_angles label"
+msgid "Infill Line Directions"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "infill_angles description"
+msgid ""
+"A list of integer line directions to use. Elements from the list are used "
+"sequentially as the layers progress and when the end of the list is reached, "
+"it starts at the beginning again. The list items are separated by commas and "
+"the whole list is contained in square brackets. Default is an empty list "
+"which means use the traditional default angles (45 and 135 degrees for the "
+"lines and zig zag patterns and 45 degrees for all other patterns)."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "sub_div_rad_mult label"
 msgid "Cubic Subdivision Radius"
 msgstr ""
@@ -1263,6 +1332,97 @@ msgid ""
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "min_infill_area label"
+msgid "Minimum Infill Area"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "min_infill_area description"
+msgid "Don't generate areas of infill smaller than this (use skin instead)."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_skins_into_infill label"
+msgid "Expand Skins Into Infill"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_skins_into_infill description"
+msgid ""
+"Expand skin areas of top and/or bottom skin of flat surfaces. By default, "
+"skins stop under the wall lines that surround infill but this can lead to "
+"holes appearing when the infill density is low. This setting extends the "
+"skins beyond the wall lines so that the infill on the next layer rests on "
+"skin."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_upper_skins label"
+msgid "Expand Upper Skins"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_upper_skins description"
+msgid ""
+"Expand upper skin areas (areas with air above) so that they support infill "
+"above."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_lower_skins label"
+msgid "Expand Lower Skins"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_lower_skins description"
+msgid ""
+"Expand lower skin areas (areas with air below) so that they are anchored by "
+"the infill layers above and below."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_skins_expand_distance label"
+msgid "Skin Expand Distance"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "expand_skins_expand_distance description"
+msgid ""
+"The distance the skins are expanded into the infill. The default distance is "
+"enough to bridge the gap between the infill lines and will stop holes "
+"appearing in the skin where it meets the wall when the infill density is "
+"low. A smaller distance will often be sufficient."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "max_skin_angle_for_expansion label"
+msgid "Maximum Skin Angle for Expansion"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "max_skin_angle_for_expansion description"
+msgid ""
+"Top and/or bottom surfaces of your object with an angle larger than this "
+"setting, won't have their top/bottom skin expanded. This avoids expanding "
+"the narrow skin areas that are created when the model surface has a near "
+"vertical slope. An angle of 0° is horizontal, while an angle of 90° is "
+"vertical."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "min_skin_width_for_expansion label"
+msgid "Minimum Skin Width for Expansion"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "min_skin_width_for_expansion description"
+msgid ""
+"Skin areas narrower than this are not expanded. This avoids expanding the "
+"narrow skin areas that are created when the model surface has a slope close "
+"to the vertical."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "material label"
 msgid "Material"
 msgstr ""
@@ -1304,8 +1464,7 @@ msgstr ""
 
 #: fdmprinter.def.json
 msgctxt "material_print_temperature description"
-msgid ""
-"The temperature used for printing. Set at 0 to pre-heat the printer manually."
+msgid "The temperature used for printing."
 msgstr ""
 
 #: fdmprinter.def.json
@@ -1376,8 +1535,8 @@ msgstr ""
 #: fdmprinter.def.json
 msgctxt "material_bed_temperature description"
 msgid ""
-"The temperature used for the heated build plate. Set at 0 to pre-heat the "
-"printer manually."
+"The temperature used for the heated build plate. If this is 0, the bed will "
+"not heat up for this print."
 msgstr ""
 
 #: fdmprinter.def.json
@@ -2217,6 +2376,16 @@ msgid "No Skin"
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "travel_retract_before_outer_wall label"
+msgid "Retract Before Outer Wall"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "travel_retract_before_outer_wall description"
+msgid "Always retract when moving to start an outer wall."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "travel_avoid_other_parts label"
 msgid "Avoid Printed Parts When Traveling"
 msgstr ""
@@ -2671,7 +2840,7 @@ msgctxt "support_z_distance description"
 msgid ""
 "Distance from the top/bottom of the support structure to the print. This gap "
 "provides clearance to remove the supports after the model is printed. This "
-"value is rounded down to a multiple of the layer height."
+"value is rounded up to a multiple of the layer height."
 msgstr ""
 
 #: fdmprinter.def.json