Update translation template files for Cura 4.3

These are the new strings in Cura 4.3.

Contributes to issue CURA-6768.

1 files changed, 216 insertions, 54 deletions

diff --git a/resources/i18n/fdmprinter.def.json.pot b/resources/i18n/fdmprinter.def.json.pot
index d1a75607cb..5e386628a0 100644
--- a/resources/i18n/fdmprinter.def.json.pot
+++ b/resources/i18n/fdmprinter.def.json.pot
@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Uranium json setting files\n"
 "Report-Msgid-Bugs-To: r.dulek@ultimaker.com\n"
-"POT-Creation-Date: 2019-07-16 14:38+0000\n"
+"POT-Creation-Date: 2019-09-10 16:55+0000\n"
 "PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
 "Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
 "Language-Team: LANGUAGE\n"
@@ -219,6 +219,16 @@ msgid "Whether the machine has a heated build plate present."
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "machine_heated_build_volume label"
+msgid "Has Build Volume Temperature Stabilization"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "machine_heated_build_volume description"
+msgid "Whether the machine is able to stabilize the build volume temperature."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "machine_center_is_zero label"
 msgid "Is Center Origin"
 msgstr ""
@@ -1413,6 +1423,56 @@ msgid "Sharpest Corner"
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "z_seam_position label"
+msgid "Z Seam Position"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position description"
+msgid "The position near where to start printing each part in a layer."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option backleft"
+msgid "Back Left"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option back"
+msgid "Back"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option backright"
+msgid "Back Right"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option right"
+msgid "Right"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option frontright"
+msgid "Front Right"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option front"
+msgid "Front"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option frontleft"
+msgid "Front Left"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "z_seam_position option left"
+msgid "Left"
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "z_seam_x label"
 msgid "Z Seam X"
 msgstr ""
@@ -1527,9 +1587,10 @@ msgstr ""
 #: fdmprinter.def.json
 msgctxt "ironing_enabled description"
 msgid ""
-"Go over the top surface one additional time, but without extruding material. "
-"This is meant to melt the plastic on top further, creating a smoother "
-"surface."
+"Go over the top surface one additional time, but this time extruding very "
+"little material. This is meant to melt the plastic on top further, creating "
+"a smoother surface. The pressure in the nozzle chamber is kept high so that "
+"the creases in the surface are filled with material."
 msgstr ""
 
 #: fdmprinter.def.json
@@ -1631,6 +1692,39 @@ msgid "The maximum instantaneous velocity change while performing ironing."
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "skin_overlap label"
+msgid "Skin Overlap Percentage"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "skin_overlap description"
+msgid ""
+"Adjust the amount of overlap between the walls and (the endpoints of) the "
+"skin-centerlines, as a percentage of the line widths of the skin lines and "
+"the innermost wall. A slight overlap allows the walls to connect firmly to "
+"the skin. Note that, given an equal skin and wall line-width, any percentage "
+"over 50% may already cause any skin to go past the wall, because at that "
+"point the position of the nozzle of the skin-extruder may already reach past "
+"the middle of the wall."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "skin_overlap_mm label"
+msgid "Skin Overlap"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "skin_overlap_mm description"
+msgid ""
+"Adjust the amount of overlap between the walls and (the endpoints of) the "
+"skin-centerlines. A slight overlap allows the walls to connect firmly to the "
+"skin. Note that, given an equal skin and wall line-width, any value over "
+"half the width of the wall may already cause any skin to go past the wall, "
+"because at that point the position of the nozzle of the skin-extruder may "
+"already reach past the middle of the wall."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "infill label"
 msgid "Infill"
 msgstr ""
@@ -1819,6 +1913,19 @@ msgid "The infill pattern is moved this distance along the Y axis."
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "infill_randomize_start_location label"
+msgid "Randomize Infill Start"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "infill_randomize_start_location description"
+msgid ""
+"Randomize which infill line is printed first. This prevents one segment "
+"becoming the strongest, but it does so at the cost of an additional travel "
+"move."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "infill_multiplier label"
 msgid "Infill Line Multiplier"
 msgstr ""
@@ -1887,39 +1994,6 @@ msgid ""
 msgstr ""
 
 #: fdmprinter.def.json
-msgctxt "skin_overlap label"
-msgid "Skin Overlap Percentage"
-msgstr ""
-
-#: fdmprinter.def.json
-msgctxt "skin_overlap description"
-msgid ""
-"Adjust the amount of overlap between the walls and (the endpoints of) the "
-"skin-centerlines, as a percentage of the line widths of the skin lines and "
-"the innermost wall. A slight overlap allows the walls to connect firmly to "
-"the skin. Note that, given an equal skin and wall line-width, any percentage "
-"over 50% may already cause any skin to go past the wall, because at that "
-"point the position of the nozzle of the skin-extruder may already reach past "
-"the middle of the wall."
-msgstr ""
-
-#: fdmprinter.def.json
-msgctxt "skin_overlap_mm label"
-msgid "Skin Overlap"
-msgstr ""
-
-#: fdmprinter.def.json
-msgctxt "skin_overlap_mm description"
-msgid ""
-"Adjust the amount of overlap between the walls and (the endpoints of) the "
-"skin-centerlines. A slight overlap allows the walls to connect firmly to the "
-"skin. Note that, given an equal skin and wall line-width, any value over "
-"half the width of the wall may already cause any skin to go past the wall, "
-"because at that point the position of the nozzle of the skin-extruder may "
-"already reach past the middle of the wall."
-msgstr ""
-
-#: fdmprinter.def.json
 msgctxt "infill_wipe_dist label"
 msgid "Infill Wipe Distance"
 msgstr ""
@@ -3515,20 +3589,6 @@ msgid ""
 msgstr ""
 
 #: fdmprinter.def.json
-msgctxt "start_layers_at_same_position label"
-msgid "Start Layers with the Same Part"
-msgstr ""
-
-#: fdmprinter.def.json
-msgctxt "start_layers_at_same_position description"
-msgid ""
-"In each layer start with printing the object near the same point, so that we "
-"don't start a new layer with printing the piece which the previous layer "
-"ended with. This makes for better overhangs and small parts, but increases "
-"printing time."
-msgstr ""
-
-#: fdmprinter.def.json
 msgctxt "layer_start_x label"
 msgid "Layer Start X"
 msgstr ""
@@ -4020,8 +4080,11 @@ msgstr ""
 #: fdmprinter.def.json
 msgctxt "support_infill_angles description"
 msgid ""
-"Orientation of the infill pattern for supports. The support infill pattern "
-"is rotated in the horizontal plane."
+"A list of integer line directions to use. Elements from the list are used "
+"sequentially as the layers progress and when the end of the list is reached, "
+"it starts at the beginning again. The list items are separated by commas and "
+"the whole list is contained in square brackets. Default is an empty list "
+"which means use the default angle 0 degrees."
 msgstr ""
 
 #: fdmprinter.def.json
@@ -4562,6 +4625,54 @@ msgid "Amount of offset applied to the floors of the support."
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "support_interface_angles label"
+msgid "Support Interface Line Directions"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "support_interface_angles description"
+msgid ""
+"A list of integer line directions to use. Elements from the list are used "
+"sequentially as the layers progress and when the end of the list is reached, "
+"it starts at the beginning again. The list items are separated by commas and "
+"the whole list is contained in square brackets. Default is an empty list "
+"which means use the default angles (alternates between 45 and 135 degrees if "
+"interfaces are quite thick or 90 degrees)."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "support_roof_angles label"
+msgid "Support Roof Line Directions"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "support_roof_angles description"
+msgid ""
+"A list of integer line directions to use. Elements from the list are used "
+"sequentially as the layers progress and when the end of the list is reached, "
+"it starts at the beginning again. The list items are separated by commas and "
+"the whole list is contained in square brackets. Default is an empty list "
+"which means use the default angles (alternates between 45 and 135 degrees if "
+"interfaces are quite thick or 90 degrees)."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "support_bottom_angles label"
+msgid "Support Floor Line Directions"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "support_bottom_angles description"
+msgid ""
+"A list of integer line directions to use. Elements from the list are used "
+"sequentially as the layers progress and when the end of the list is reached, "
+"it starts at the beginning again. The list items are separated by commas and "
+"the whole list is contained in square brackets. Default is an empty list "
+"which means use the default angles (alternates between 45 and 135 degrees if "
+"interfaces are quite thick or 90 degrees)."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "support_fan_enable label"
 msgid "Fan Speed Override"
 msgstr ""
@@ -5909,7 +6020,9 @@ msgctxt "meshfix_maximum_deviation description"
 msgid ""
 "The maximum deviation allowed when reducing the resolution for the Maximum "
 "Resolution setting. If you increase this, the print will be less accurate, "
-"but the g-code will be smaller."
+"but the g-code will be smaller. Maximum Deviation is a limit for Maximum "
+"Resolution, so if the two conflict the Maximum Deviation will always be held "
+"true."
 msgstr ""
 
 #: fdmprinter.def.json
@@ -7093,6 +7206,55 @@ msgid "The distance to move the head back and forth across the brush."
 msgstr ""
 
 #: fdmprinter.def.json
+msgctxt "small_hole_max_size label"
+msgid "Small Hole Max Size"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_hole_max_size description"
+msgid ""
+"Holes and part outlines with a diameter smaller than this will be printed "
+"using Small Feature Speed."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_max_length label"
+msgid "Small Feature Max Length"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_max_length description"
+msgid ""
+"Feature outlines that are shorter than this length will be printed using "
+"Small Feature Speed."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_speed_factor label"
+msgid "Small Feature Speed"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_speed_factor description"
+msgid ""
+"Small features will be printed at this percentage of their normal print "
+"speed. Slower printing can help with adhestion and accuracy."
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_speed_factor_0 label"
+msgid "First Layer Speed"
+msgstr ""
+
+#: fdmprinter.def.json
+msgctxt "small_feature_speed_factor_0 description"
+msgid ""
+"Small features on the first layer will be printed at this percentage of "
+"their normal print speed. Slower printing can help with adhestion and "
+"accuracy."
+msgstr ""
+
+#: fdmprinter.def.json
 msgctxt "command_line_settings label"
 msgid "Command Line Settings"
 msgstr ""