Publish Ultimaker 2+ Connect profiles

This is the new printer from Ultimaker.

62 files changed, 2132 insertions, 0 deletions

diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..43dc3faca8
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.25_normal.inst.cfg
@@ -0,0 +1,23 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_abs
+variant = 0.25 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.2
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..286bebf854
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_fast.inst.cfg
@@ -0,0 +1,27 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_abs
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.2
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
+speed_print = 55
+speed_travel = 150
+speed_layer_0 = =round(speed_print * 30 / 55)
+speed_wall = =math.ceil(speed_print * 40 / 55)
+speed_topbottom = =math.ceil(speed_print * 30 / 55)
+speed_infill = =math.ceil(speed_print * 55 / 55)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_high.inst.cfg
new file mode 100644
index 0000000000..614744aada
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_high.inst.cfg
@@ -0,0 +1,26 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_abs
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.2
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
+speed_print = 45
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_wall = =math.ceil(speed_print * 30 / 45)
+speed_topbottom = =math.ceil(speed_print * 15 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..b84d4c9a3f
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.4_normal.inst.cfg
@@ -0,0 +1,26 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_abs
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.2
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
+speed_print = 45
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_wall = =math.ceil(speed_print * 30 / 45)
+speed_topbottom = =math.ceil(speed_print * 20 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..ac192c9685
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.6_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_abs
+variant = 0.6 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.5
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 20
+cool_min_speed = 20
+infill_sparse_density = 20
+speed_infill = =math.ceil(speed_print * 55 / 40)
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..d2cffb1c55
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_abs_0.8_normal.inst.cfg
@@ -0,0 +1,23 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_abs
+variant = 0.8 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.5
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 25
+cool_min_speed = 15
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..efb0361c6e
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.25_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_cpe
+variant = 0.25 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.2
+cool_min_layer_time = 2
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 15
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..a45f1d3e6c
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_fast.inst.cfg
@@ -0,0 +1,29 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_cpe
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.8
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 40 / 45)
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
+speed_wall_0 = =math.ceil(speed_print * 30 / 45)
+speed_topbottom = =math.ceil(speed_print * 30 / 45)
+speed_wall_x = =math.ceil(speed_print * 40 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_high.inst.cfg
new file mode 100644
index 0000000000..bcbc535fe0
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_high.inst.cfg
@@ -0,0 +1,26 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_cpe
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.8
+cool_min_layer_time = 2
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 15
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = =math.ceil(speed_print * 30 / 45)
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
+speed_topbottom = =math.ceil(speed_print * 15 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..71f2916a3a
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.4_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_cpe
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.8
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = =math.ceil(speed_print * 30 / 45)
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..fabf1214ee
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.6_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_cpe
+variant = 0.6 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.8
+cool_min_layer_time = 5
+cool_min_layer_time_fan_speed_max = 20
+cool_min_speed = 8
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..96d2433ffa
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpe_0.8_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_cpe
+variant = 0.8 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.8
+cool_min_layer_time = 3
+cool_min_layer_time_fan_speed_max = 25
+cool_min_speed = 8
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_draft.inst.cfg
new file mode 100644
index 0000000000..ed6f5a0c5e
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_draft.inst.cfg
@@ -0,0 +1,42 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+material = generic_cpe_plus
+variant = 0.4 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+line_width = 0.38
+raft_airgap = 0.37
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.38
+speed_layer_0 = =math.ceil(speed_print * 15 / 25)
+speed_print = 25
+speed_topbottom = =math.ceil(speed_print * 20 / 25)
+speed_wall_0 = =math.ceil(speed_print * 20 / 25)
+speed_wall_x = =speed_print
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.5
+wall_thickness = 1.14
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..2aebe1e918
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.4_normal.inst.cfg
@@ -0,0 +1,42 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_cpe_plus
+variant = 0.4 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+line_width = 0.38
+raft_airgap = 0.37
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.38
+speed_layer_0 = =math.ceil(speed_print * 15 / 35)
+speed_print = 35
+speed_topbottom = =math.ceil(speed_print * 20 / 35)
+speed_wall_0 = =math.ceil(speed_print * 20 / 35)
+speed_wall_x = =math.ceil(speed_print * 30 / 35)
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.5
+wall_thickness = 1.14
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_draft.inst.cfg
new file mode 100644
index 0000000000..78ffe10ce9
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_draft.inst.cfg
@@ -0,0 +1,46 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -2
+material = generic_cpe_plus
+variant = 0.6 mm
+
+[values]
+cool_fan_speed = 45
+cool_fan_speed_min = =cool_fan_speed * 25 / 45
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+line_width = 0.57
+raft_airgap = 0.37
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.57
+raft_surface_thickness = 0.2
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 25
+speed_topbottom = =math.ceil(speed_print * 20 / 25)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 20 / 25)
+speed_wall_x = =speed_print
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_line_distance = 2.85
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.22
+top_bottom_thickness = 0.75
+wall_thickness = 1.14
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..2099ea7cbf
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.6_normal.inst.cfg
@@ -0,0 +1,46 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = 0
+material = generic_cpe_plus
+variant = 0.6 mm
+
+[values]
+cool_fan_speed = 45
+cool_fan_speed_min = =cool_fan_speed * 25 / 45
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+line_width = 0.57
+raft_airgap = 0.37
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.57
+raft_surface_thickness = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 35)
+speed_print = 35
+speed_topbottom = =math.ceil(speed_print * 20 / 35)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 30 / 35)
+speed_wall_x = =speed_print
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_line_distance = 2.85
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.22
+top_bottom_thickness = 0.75
+wall_thickness = 1.14
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_draft.inst.cfg
new file mode 100644
index 0000000000..bf4be03a20
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_draft.inst.cfg
@@ -0,0 +1,41 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -2
+material = generic_cpe_plus
+variant = 0.8 mm
+
+[values]
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.37
+raft_base_line_width = 1.6
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+speed_layer_0 = =round(speed_print * 30 / 25)
+speed_print = 25
+speed_topbottom = =math.ceil(speed_print * 20 / 25)
+speed_wall_0 = =math.ceil(speed_print * 20 / 25)
+speed_wall_x = =speed_print
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
+retraction_combing_max_distance = 50
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..f1dd92db53
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_cpep_0.8_normal.inst.cfg
@@ -0,0 +1,41 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = 0
+material = generic_cpe_plus
+variant = 0.8 mm
+
+[values]
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.37
+raft_base_line_width = 1.6
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+speed_topbottom = =math.ceil(speed_print * 20 / 30)
+speed_wall_0 = =math.ceil(speed_print * 20 / 30)
+speed_wall_x = =speed_print
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
+retraction_combing_max_distance = 50
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Coarse_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Coarse_Quality.inst.cfg
new file mode 100644
index 0000000000..e642fb9857
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Coarse_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Coarse Quality
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = coarse
+weight = -4
+global_quality = True
+
+[values]
+layer_height = 0.4
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Draft_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Draft_Quality.inst.cfg
new file mode 100644
index 0000000000..27801010ca
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Draft_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Draft Quality
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+global_quality = True
+
+[values]
+layer_height = 0.2
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Extra_Coarse_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Extra_Coarse_Quality.inst.cfg
new file mode 100644
index 0000000000..8db35032aa
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Extra_Coarse_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Extra Coarse Quality
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = extracoarse
+weight = -3
+global_quality = True
+
+[values]
+layer_height = 0.6
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Fast_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Fast_Quality.inst.cfg
new file mode 100644
index 0000000000..39c8927c80
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Fast_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+global_quality = True
+
+[values]
+layer_height = 0.15
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_High_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_High_Quality.inst.cfg
new file mode 100644
index 0000000000..3e3ca23ac7
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_High_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+global_quality = True
+
+[values]
+layer_height = 0.06
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Normal_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Normal_Quality.inst.cfg
new file mode 100644
index 0000000000..1530bdb200
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Normal_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+global_quality = True
+
+[values]
+layer_height = 0.1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_global_Slightly_Coarse_Quality.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_global_Slightly_Coarse_Quality.inst.cfg
new file mode 100644
index 0000000000..e3bac84215
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_global_Slightly_Coarse_Quality.inst.cfg
@@ -0,0 +1,14 @@
+[general]
+version = 4
+name = Coarse Quality
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -4
+global_quality = True
+
+[values]
+layer_height = 0.3
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_high.inst.cfg
new file mode 100644
index 0000000000..2fd638f0e9
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_high.inst.cfg
@@ -0,0 +1,43 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_nylon
+variant = 0.25 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.1
+raft_airgap = 0.15
+raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 40)
+speed_print = 40
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 40)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 20 / 40)
+speed_wall_x = =speed_print
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1
+speed_infill = =math.ceil(speed_print * 40 / 40)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..d7a64e12c8
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.25_normal.inst.cfg
@@ -0,0 +1,42 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_nylon
+variant = 0.25 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.1
+raft_airgap = 0.15
+raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 40)
+speed_print = 40
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 40)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 20 / 40)
+speed_wall_x = =speed_print
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..d62a4e79ee
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_fast.inst.cfg
@@ -0,0 +1,44 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_nylon
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_layer_time = 3
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.57
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.5
+raft_surface_thickness = 0.15
+speed_layer_0 = =math.ceil(speed_print * 30 / 45)
+speed_print = 45
+speed_topbottom = =math.ceil(speed_print * 20 / 45)
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 40 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
+speed_wall_0 = =math.ceil(speed_print * 30 / 45)
+speed_wall_x = =math.ceil(speed_print * 40 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..a6161c2a07
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.4_normal.inst.cfg
@@ -0,0 +1,40 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_nylon
+variant = 0.4 mm
+
+[values]
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_layer_time = 3
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.57
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.5
+raft_surface_thickness = 0.15
+speed_layer_0 = =math.ceil(speed_print * 30 / 45)
+speed_print = 45
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 40 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_fast.inst.cfg
new file mode 100644
index 0000000000..dbb90918b8
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_fast.inst.cfg
@@ -0,0 +1,47 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -1
+material = generic_nylon
+variant = 0.6 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.44
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 55)
+speed_print = 55
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 55)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 55)
+speed_wall_x = =math.ceil(speed_print * 40 / 55)
+support_angle = 45
+support_bottom_distance = 0.55
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_top_distance = 0.55
+support_xy_distance = 0.7
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.2
+speed_infill = =math.ceil(speed_print * 55 / 55)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..172ef69c01
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.6_normal.inst.cfg
@@ -0,0 +1,44 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_nylon
+variant = 0.6 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.44
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 55)
+speed_print = 55
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 55)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 55)
+speed_wall_x = =math.ceil(speed_print * 40 / 55)
+support_angle = 45
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_xy_distance = 0.7
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.2
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_draft.inst.cfg
new file mode 100644
index 0000000000..c85bacb89e
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_draft.inst.cfg
@@ -0,0 +1,45 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -2
+material = generic_nylon
+variant = 0.8 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.25
+raft_airgap = 0.44
+raft_base_line_width = 1.6
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 55)
+speed_print = 55
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 55)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 55)
+speed_wall_x = =math.ceil(speed_print * 40 / 55)
+support_angle = 45
+support_bottom_distance = 0.65
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_top_distance = 0.5
+support_xy_distance = 0.75
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 2.4
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..153f206b19
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_nylon_0.8_normal.inst.cfg
@@ -0,0 +1,45 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = 0
+material = generic_nylon
+variant = 0.8 mm
+
+[values]
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.25
+raft_airgap = 0.44
+raft_base_line_width = 1.6
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =round(speed_print * 30 / 55)
+speed_print = 55
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 55)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 55)
+speed_wall_x = =math.ceil(speed_print * 40 / 55)
+support_angle = 45
+support_bottom_distance = 0.65
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_pattern = lines
+support_top_distance = 0.5
+support_xy_distance = 0.75
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 2.4
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_high.inst.cfg
new file mode 100644
index 0000000000..062e7f97b5
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_high.inst.cfg
@@ -0,0 +1,37 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_pc
+variant = 0.25 mm
+
+[values]
+brim_line_count = 32
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 2
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.2
+raft_airgap = 0.25
+raft_base_line_spacing = 1
+raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 0.88
+speed_topbottom = =math.ceil(speed_print * 15 / 30)
\ No newline at end of file
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..20ab28f97b
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.25_normal.inst.cfg
@@ -0,0 +1,36 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_pc
+variant = 0.25 mm
+
+[values]
+brim_line_count = 32
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 2
+cool_min_speed = 15
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.2
+raft_airgap = 0.25
+raft_base_line_spacing = 1
+raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 0.88
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..249bfb9053
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_fast.inst.cfg
@@ -0,0 +1,39 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_pc
+variant = 0.4 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.3
+raft_airgap = 0.35
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall_0 = =math.ceil(speed_print * 20 / 45)
+speed_wall_x = =math.ceil(speed_print * 30 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 1.2
+speed_topbottom = =math.ceil(speed_print * 30 / 45)
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..86a2dabb6f
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.4_normal.inst.cfg
@@ -0,0 +1,37 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_pc
+variant = 0.4 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.3
+raft_airgap = 0.35
+raft_base_line_spacing = 1.6
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall_0 = =math.ceil(speed_print * 20 / 45)
+speed_wall_x = =math.ceil(speed_print * 30 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 1.2
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_fast.inst.cfg
new file mode 100644
index 0000000000..95bbbff2d3
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_fast.inst.cfg
@@ -0,0 +1,44 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -1
+material = generic_pc
+variant = 0.6 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.52
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+speed_layer_0 = =math.ceil(speed_print * 30 / 45)
+speed_print = 45
+speed_topbottom = =math.ceil(speed_print * 20 / 45)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 30 / 45)
+speed_wall_x = =math.ceil(speed_print * 40 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_line_distance = 3.5333
+support_pattern = lines
+support_z_distance = 0.21
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
+speed_infill = =math.ceil(speed_print * 45 / 45)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..c4f451d972
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.6_normal.inst.cfg
@@ -0,0 +1,43 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_pc
+variant = 0.6 mm
+
+[values]
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.52
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+speed_layer_0 = =math.ceil(speed_print * 30 / 45)
+speed_print = 45
+speed_topbottom = =math.ceil(speed_print * 20 / 45)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 30 / 45)
+speed_wall_x = =math.ceil(speed_print * 40 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_line_distance = 3.5333
+support_pattern = lines
+support_z_distance = 0.21
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..c9fe800c7b
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pc_0.8_normal.inst.cfg
@@ -0,0 +1,37 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = 0
+material = generic_pc
+variant = 0.8 mm
+
+[values]
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
+infill_sparse_density = 20
+layer_0_z_overlap = 0.22
+raft_airgap = 0.47
+raft_base_line_width = 1.6
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = =20 if support_enable else 0 if support_tree_enable else 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..3c2288f052
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.25_normal.inst.cfg
@@ -0,0 +1,21 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_pla
+variant = 0.25 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_draft.inst.cfg
new file mode 100644
index 0000000000..48d37de4c6
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_draft.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+material = generic_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 60)
+speed_print = 60
+speed_topbottom = =math.ceil(speed_print * 30 / 60)
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 50 / 60)
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..23e1a1396a
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_fast.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 60)
+speed_print = 60
+speed_topbottom = =math.ceil(speed_print * 30 / 60)
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 50 / 60)
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_high.inst.cfg
new file mode 100644
index 0000000000..8e8cea39df
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_high.inst.cfg
@@ -0,0 +1,22 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = =math.ceil(speed_print * 20 / 50)
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..68c1a2960e
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.4_normal.inst.cfg
@@ -0,0 +1,22 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = =math.ceil(speed_print * 20 / 50)
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..942f69c910
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.6_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_pla
+variant = 0.6 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 55)
+speed_print = 55
+speed_topbottom = =math.ceil(speed_print * 20 / 55)
+speed_wall = =math.ceil(speed_print * 40 / 55)
+speed_wall_0 = =math.ceil(speed_print * 25 / 55)
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..3bae17f1a7
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pla_0.8_normal.inst.cfg
@@ -0,0 +1,22 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_pla
+variant = 0.8 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+speed_wall_0 = =math.ceil(speed_print * 25 / 40)
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..787cf2d779
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_fast.inst.cfg
@@ -0,0 +1,72 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_pp
+variant = 0.4 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.4 / 0.38, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_min_travel = 0.5
+retraction_prime_speed = 15
+skin_overlap = 10
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.38 / 0.38, 2)
+wall_thickness = 0.76
+speed_wall_x = =math.ceil(speed_print * 25 / 25)
+speed_infill = =math.ceil(speed_print * 25 / 25)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..48062237b6
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.4_normal.inst.cfg
@@ -0,0 +1,70 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_pp
+variant = 0.4 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.4 / 0.38, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_min_travel = 0.5
+retraction_prime_speed = 15
+skin_overlap = 10
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.38 / 0.38, 2)
+wall_thickness = 0.76
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_draft.inst.cfg
new file mode 100644
index 0000000000..86cecc00f0
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_draft.inst.cfg
@@ -0,0 +1,71 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+material = generic_pp
+variant = 0.6 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.6 / 0.57, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_prime_speed = 15
+skin_overlap = 10
+skirt_brim_line_width = 0.6
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.1
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.57 / 0.57, 2)
+wall_thickness = 1.14
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_fast.inst.cfg
new file mode 100644
index 0000000000..6e21a94da9
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.6_fast.inst.cfg
@@ -0,0 +1,73 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_pp
+variant = 0.6 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.6 / 0.57, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_prime_speed = 15
+skin_overlap = 10
+skirt_brim_line_width = 0.6
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.1
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.57 / 0.57, 2)
+wall_thickness = 1.14
+speed_wall_x = =math.ceil(speed_print * 25 / 25)
+speed_infill = =math.ceil(speed_print * 25 / 25)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_draft.inst.cfg
new file mode 100644
index 0000000000..d93d807812
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_draft.inst.cfg
@@ -0,0 +1,71 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+material = generic_pp
+variant = 0.8 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.8 / 0.76, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_prime_speed = 15
+skin_overlap = 10
+skirt_brim_line_width = 0.8
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.5
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.76 / 0.76, 2)
+wall_thickness = 1.52
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_verydraft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_verydraft.inst.cfg
new file mode 100644
index 0000000000..bd28518e4a
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_pp_0.8_verydraft.inst.cfg
@@ -0,0 +1,71 @@
+[general]
+version = 4
+name = Extra Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = slightlycoarse
+weight = -3
+material = generic_pp
+variant = 0.8 mm
+
+[values]
+acceleration_enabled = True
+acceleration_layer_0 = =acceleration_topbottom
+acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_print = 4000
+acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
+acceleration_support_interface = =acceleration_topbottom
+acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
+acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
+acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
+brim_width = 20
+cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 6
+cool_min_speed = 20
+infill_line_width = =round(line_width * 0.8 / 0.76, 2)
+infill_overlap = 0
+infill_pattern = tetrahedral
+infill_wipe_dist = 0
+jerk_enabled = True
+jerk_layer_0 = =jerk_topbottom
+jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
+jerk_print = 25
+jerk_support = =math.ceil(jerk_print * 15 / 25)
+jerk_support_interface = =jerk_topbottom
+jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
+jerk_wall = =math.ceil(jerk_print * 10 / 25)
+jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
+line_width = =machine_nozzle_size * 0.95
+multiple_mesh_overlap = 0
+retraction_count_max = 12
+retraction_extrusion_window = 1
+retraction_hop = 0.15
+retraction_hop_enabled = True
+retraction_hop_only_when_collides = True
+retraction_prime_speed = 15
+skin_overlap = 10
+skirt_brim_line_width = 0.8
+speed_layer_0 = =speed_print
+speed_prime_tower = =speed_topbottom
+speed_print = 25
+speed_support_interface = =speed_topbottom
+speed_topbottom = =math.ceil(speed_print * 25 / 25)
+speed_travel = 250
+speed_travel_layer_0 = 50
+speed_wall = =math.ceil(speed_print * 25 / 25)
+speed_wall_0 = =math.ceil(speed_wall * 20 / 25)
+support_angle = 60
+support_bottom_distance = =support_z_distance / 2
+support_top_distance = =support_z_distance
+support_xy_distance = =wall_line_width_0 * 2.5
+support_xy_distance_overhang = =wall_line_width_0
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.5
+travel_avoid_distance = 3
+wall_0_inset = 0
+wall_line_width_x = =round(line_width * 0.76 / 0.76, 2)
+wall_thickness = 1.52
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.25_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.25_normal.inst.cfg
new file mode 100644
index 0000000000..8d1a329422
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.25_normal.inst.cfg
@@ -0,0 +1,21 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_tough_pla
+variant = 0.25 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_draft.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_draft.inst.cfg
new file mode 100644
index 0000000000..06474184be
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_draft.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fast
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -2
+material = generic_tough_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = =math.ceil(speed_print * 30 / 50)
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 40 / 50)
+top_bottom_thickness = 0.75
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_fast.inst.cfg
new file mode 100644
index 0000000000..d25748e82f
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_fast.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_tough_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+speed_topbottom = =math.ceil(speed_print * 30 / 40)
+speed_travel = 150
+speed_wall = =math.ceil(speed_print * 30 / 40)
+top_bottom_thickness = 0.75
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..7660043d51
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.4_normal.inst.cfg
@@ -0,0 +1,23 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_tough_pla
+variant = 0.4 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+speed_topbottom = =math.ceil(speed_print * 20 / 40)
+speed_wall = =math.ceil(speed_print * 30 / 40)
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.6_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.6_normal.inst.cfg
new file mode 100644
index 0000000000..0371972d42
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.6_normal.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = 0
+material = generic_tough_pla
+variant = 0.6 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = =math.ceil(speed_print * 20 / 50)
+speed_wall = =math.ceil(speed_print * 40 / 50)
+speed_wall_0 = =math.ceil(speed_print * 30 / 50)
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.8_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.8_normal.inst.cfg
new file mode 100644
index 0000000000..8fd4c747c4
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpla_0.8_normal.inst.cfg
@@ -0,0 +1,22 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = draft
+weight = -1
+material = generic_tough_pla
+variant = 0.8 mm
+
+[values]
+cool_min_layer_time = 5
+cool_min_speed = 10
+infill_sparse_density = 20
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+speed_wall_0 = =math.ceil(speed_print * 25 / 40)
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.25_high.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.25_high.inst.cfg
new file mode 100644
index 0000000000..f03f8ca03d
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.25_high.inst.cfg
@@ -0,0 +1,43 @@
+[general]
+version = 4
+name = Extra Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = high
+weight = 1
+material = generic_tpu
+variant = 0.25 mm
+
+[values]
+adhesion_type = brim
+brim_line_count = 20
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_layer_time = 7
+cool_min_speed = 15
+infill_sparse_density = 10
+layer_0_z_overlap = 0.1
+raft_airgap = 0.2
+raft_base_line_spacing = 1
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.2
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 40)
+speed_print = 40
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 40)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 40)
+speed_wall_x = =math.ceil(speed_print * 38 / 40)
+support_angle = 45
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 0.88
+speed_infill = =math.ceil(speed_print * 40 / 40)
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.4_normal.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.4_normal.inst.cfg
new file mode 100644
index 0000000000..40e8daa71f
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.4_normal.inst.cfg
@@ -0,0 +1,40 @@
+[general]
+version = 4
+name = Fine
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = normal
+weight = 0
+material = generic_tpu
+variant = 0.4 mm
+
+[values]
+adhesion_type = brim
+brim_line_count = 20
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_layer_time = 10
+cool_min_speed = 15
+infill_sparse_density = 10
+raft_base_line_spacing = 2
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_margin = 12
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 40)
+speed_print = 40
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 40)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 20 / 40)
+speed_wall_x = =math.ceil(speed_print * 35 / 40)
+support_angle = 45
+support_enable = True
+support_infill_rate = =25 if support_enable else 0 if support_tree_enable else 25
+support_xy_distance = 0.65
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.05
diff --git a/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.6_fast.inst.cfg b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.6_fast.inst.cfg
new file mode 100644
index 0000000000..35ce420405
--- /dev/null
+++ b/resources/quality/ultimaker2_plus_connect/um2pc_tpu_0.6_fast.inst.cfg
@@ -0,0 +1,45 @@
+[general]
+version = 4
+name = Normal
+definition = ultimaker2_plus_connect
+
+[metadata]
+setting_version = 16
+type = quality
+quality_type = fast
+weight = -1
+material = generic_tpu
+variant = 0.6 mm
+
+[values]
+adhesion_type = brim
+brim_line_count = 20
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_sparse_density = 10
+layer_0_z_overlap = 0.12
+line_width = 0.57
+raft_airgap = 0.24
+raft_base_line_spacing = 1.2
+raft_base_line_width = 0.6
+raft_interface_line_spacing = 1.2
+raft_interface_line_width = 0.57
+raft_margin = 15
+raft_surface_line_width = 0.5
+retraction_hop_enabled = 0.2
+speed_layer_0 = =math.ceil(speed_print * 30 / 45)
+speed_print = 45
+speed_support = 40
+speed_topbottom = =math.ceil(speed_print * 35 / 45)
+speed_travel = 150
+speed_wall_0 = =math.ceil(speed_print * 15 / 45)
+speed_wall_x = =math.ceil(speed_print * 40 / 45)
+support_angle = 45
+support_enable = True
+support_infill_rate = =0 if support_structure == 'tree' else 25
+support_xy_distance = 0.7
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.14
+speed_infill = =math.ceil(speed_print * 45 / 45)