diff options
26 files changed, 4 insertions, 58 deletions
diff --git a/resources/definitions/ultimaker.def.json b/resources/definitions/ultimaker.def.json index 8fd6bfce08..ae2f6c618e 100644 --- a/resources/definitions/ultimaker.def.json +++ b/resources/definitions/ultimaker.def.json @@ -221,7 +221,7 @@ "value": true }, "support_infill_rate": { - "value": 80 + "value": "=80 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 80" }, "support_offset": { "value": "=2*line_width" @@ -247,6 +247,9 @@ "support_interface_pattern": { "value": "zigzag" }, + "support_interface_enable": { + "value": true + }, "minimum_interface_area": { "value": "=minimum_support_area" }, diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.25_PC_Normal_Quality.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.25_PC_Normal_Quality.inst.cfg index ec8409137c..20d644b0ac 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.25_PC_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.25_PC_Normal_Quality.inst.cfg @@ -40,7 +40,6 @@ speed_wall = =math.ceil(speed_print * 40 / 50) speed_wall_0 = =math.ceil(speed_wall * 25 / 40) support_bottom_distance = =support_z_distance support_interface_density = 87.5 -support_interface_pattern = lines switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 35 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Draft_Print.inst.cfg index c622591c90..aa575d573e 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Draft_Print.inst.cfg @@ -27,13 +27,7 @@ speed_wall = =math.ceil(speed_print * 50 / 70) speed_wall_0 = =math.ceil(speed_wall * 35 / 50) top_bottom_thickness = 1 support_brim_enable = True -support_interface_enable = True support_interface_density = =min(extruderValues('material_surface_energy')) -support_interface_pattern = ='lines' if support_interface_density < 100 else 'concentric' support_top_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 2) * layer_height support_bottom_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 2) * layer_height support_angle = 45 -support_join_distance = 5 -support_offset = 2 -support_pattern = triangles -support_infill_rate = =10 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 10 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Fast_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Fast_Print.inst.cfg index e399b3c988..d4918ec6a3 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Fast_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Fast_Print.inst.cfg @@ -26,13 +26,7 @@ speed_wall = =math.ceil(speed_print * 40 / 80) speed_wall_0 = =math.ceil(speed_wall * 30 / 40) top_bottom_thickness = 1 support_brim_enable = True -support_interface_enable = True support_interface_density = =min(extruderValues('material_surface_energy')) -support_interface_pattern = ='lines' if support_interface_density < 100 else 'concentric' support_top_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 1) * layer_height support_bottom_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 2) * layer_height support_angle = 45 -support_join_distance = 5 -support_offset = 2 -support_pattern = triangles -support_infill_rate = =10 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 10 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Normal_Quality.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Normal_Quality.inst.cfg index 7cd771e0fb..5a0783f3a4 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_BAM_Normal_Quality.inst.cfg @@ -24,14 +24,8 @@ prime_tower_enable = =min(extruderValues('material_surface_energy')) < 100 skin_overlap = 10 speed_layer_0 = =math.ceil(speed_print * 20 / 70) support_brim_enable = True -support_interface_enable = True support_interface_density = =min(extruderValues('material_surface_energy')) -support_interface_pattern = ='lines' if support_interface_density < 100 else 'concentric' support_top_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 1) * layer_height support_bottom_distance = =math.ceil(min(extruderValues('material_adhesion_tendency')) / 2) * layer_height support_angle = 45 -support_join_distance = 5 -support_offset = 2 -support_pattern = triangles -support_infill_rate = =10 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 10 top_bottom_thickness = 1 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Draft_Print.inst.cfg index 1e2f58a3c3..1137a88abf 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Draft_Print.inst.cfg @@ -47,7 +47,6 @@ speed_wall = =math.ceil(speed_print * 40 / 50) speed_wall_0 = =math.ceil(speed_wall * 25 / 40) support_bottom_distance = =support_z_distance support_interface_density = 87.5 -support_interface_pattern = lines switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 35 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Fast_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Fast_Print.inst.cfg index ce5d8a5c89..d2887d38a9 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Fast_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Fast_Print.inst.cfg @@ -47,7 +47,6 @@ speed_wall = =math.ceil(speed_print * 40 / 50) speed_wall_0 = =math.ceil(speed_wall * 25 / 40) support_bottom_distance = =support_z_distance support_interface_density = 87.5 -support_interface_pattern = lines switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 35 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_High_Quality.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_High_Quality.inst.cfg index 99d5d7ef1d..deac4e0d75 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_High_Quality.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_High_Quality.inst.cfg @@ -49,7 +49,6 @@ speed_wall = =math.ceil(speed_print * 40 / 50) speed_wall_0 = =math.ceil(speed_wall * 25 / 40) support_bottom_distance = =support_z_distance support_interface_density = 87.5 -support_interface_pattern = lines switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 35 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Normal_Quality.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Normal_Quality.inst.cfg index 15b7a619e8..4cca702d7c 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Normal_Quality.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.4_PC_Normal_Quality.inst.cfg @@ -47,7 +47,6 @@ speed_wall = =math.ceil(speed_print * 40 / 50) speed_wall_0 = =math.ceil(speed_wall * 25 / 40) support_bottom_distance = =support_z_distance support_interface_density = 87.5 -support_interface_pattern = lines switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 35 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg index f45f9f403a..89a55e3f6f 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_Nylon_Superdraft_Print.inst.cfg @@ -26,7 +26,6 @@ raft_interface_thickness = =round(machine_nozzle_size * 0.3 / 0.4, 2) raft_margin = 10 raft_surface_thickness = =round(machine_nozzle_size * 0.2 / 0.4, 2) support_angle = 70 -support_xy_distance = =wall_line_width_0 * 1.5 switch_extruder_prime_speed = 30 switch_extruder_retraction_amount = 30 switch_extruder_retraction_speeds = 40 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Draft_Print.inst.cfg index 4ad620367d..9575708085 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Draft_Print.inst.cfg @@ -25,7 +25,6 @@ material_shrinkage_percentage_xy = 100.2 material_shrinkage_percentage_z = 100.1 prime_tower_enable = True support_angle = 70 -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 retract_at_layer_change = False speed_print = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Superdraft_Print.inst.cfg index 7acfa04a29..d85aeb3f9b 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Superdraft_Print.inst.cfg @@ -26,7 +26,6 @@ material_shrinkage_percentage_z = 100.1 prime_tower_enable = True raft_margin = 10 support_angle = 70 -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 retract_at_layer_change = False speed_print = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Verydraft_Print.inst.cfg index 756316ed7f..e39360b6ca 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PLA_Verydraft_Print.inst.cfg @@ -25,7 +25,6 @@ material_shrinkage_percentage_xy = 100.2 material_shrinkage_percentage_z = 100.1 prime_tower_enable = True support_angle = 70 -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 retract_at_layer_change = False speed_print = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Draft_Print.inst.cfg index aa86db8c84..6ac4b46773 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Draft_Print.inst.cfg @@ -33,7 +33,6 @@ retraction_min_travel = 1.5 retraction_prime_speed = 15 speed_wall_x = =math.ceil(speed_wall * 30 / 30) support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Superdraft_Print.inst.cfg index 4bf0036315..20b1255a88 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Superdraft_Print.inst.cfg @@ -34,7 +34,6 @@ retraction_prime_speed = 15 speed_wall_x = =math.ceil(speed_wall * 30 / 30) speed_infill = =math.ceil(speed_wall * 30 / 30) support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Verydraft_Print.inst.cfg index 69a33b38f8..be840f56b1 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_PP_Verydraft_Print.inst.cfg @@ -32,7 +32,6 @@ retraction_min_travel = 1.5 retraction_prime_speed = 15 speed_wall_x = =math.ceil(speed_wall * 30 / 30) support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPLA_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPLA_Draft_Print.inst.cfg index 7587ebf336..fbf2ad1733 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPLA_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPLA_Draft_Print.inst.cfg @@ -32,5 +32,4 @@ speed_topbottom = =round(speed_print * 35 / 45) speed_wall = =round(speed_print * 40 / 45) speed_wall_0 = =round(speed_print * 35 / 45) support_angle = 70 -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 6 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Draft_Print.inst.cfg index 9301d7d69f..0cdd20604a 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Draft_Print.inst.cfg @@ -40,7 +40,6 @@ speed_wall = =math.ceil(speed_print * 30 / 30) speed_wall_x = =math.ceil(speed_wall * 30 / 30) support_angle = 50 support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Superdraft_Print.inst.cfg index f410bd8c85..3e85f26972 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Superdraft_Print.inst.cfg @@ -41,7 +41,6 @@ speed_wall_x = =speed_print speed_infill = =speed_print support_angle = 50 support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Verydraft_Print.inst.cfg index 3df2f2ca0e..9ea2343841 100644 --- a/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_aa0.8_TPU_Verydraft_Print.inst.cfg @@ -40,7 +40,6 @@ speed_wall = =math.ceil(speed_print * 30 / 30) speed_wall_x = =math.ceil(speed_wall * 30 / 30) support_angle = 50 support_bottom_distance = =support_z_distance -support_offset = =line_width switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 20 switch_extruder_retraction_speeds = 45 diff --git a/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Superdraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Superdraft_Print.inst.cfg index 9a8a17da20..46fe19534f 100644 --- a/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Superdraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Superdraft_Print.inst.cfg @@ -16,4 +16,3 @@ brim_replaces_support = False material_standby_temperature = 100 retraction_count_max = 5 support_brim_enable = True -support_interface_height = 0.9 diff --git a/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Verydraft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Verydraft_Print.inst.cfg index 4229ad1758..48543745dd 100644 --- a/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Verydraft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_bb0.8_PVA_Verydraft_Print.inst.cfg @@ -17,4 +17,3 @@ material_standby_temperature = 100 retraction_count_max = 5 support_brim_enable = True support_infill_sparse_thickness = 0.3 -support_interface_height = 1.2 diff --git a/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Draft_Print.inst.cfg index 6a4115dd82..d6f54f2e49 100644 --- a/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Draft_Print.inst.cfg @@ -34,6 +34,4 @@ speed_wall = =math.ceil(speed_print * 40 / 45) speed_wall_x = =speed_wall speed_wall_0 = =math.ceil(speed_wall * 35 / 40) support_angle = 70 -support_pattern = ='triangles' -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 diff --git a/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Fast_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Fast_Print.inst.cfg index 7392f4e6ee..c11af88907 100644 --- a/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Fast_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_cc0.4_PLA_Fast_Print.inst.cfg @@ -34,6 +34,4 @@ speed_wall = =math.ceil(speed_print * 40 / 45) speed_wall_x = =speed_wall speed_wall_0 = =math.ceil(speed_wall * 35 / 40) support_angle = 70 -support_pattern = ='triangles' -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 diff --git a/resources/quality/ultimaker_s5/um_s5_cc0.6_PLA_Draft_Print.inst.cfg b/resources/quality/ultimaker_s5/um_s5_cc0.6_PLA_Draft_Print.inst.cfg index 053b9399a5..a2769f7e88 100644 --- a/resources/quality/ultimaker_s5/um_s5_cc0.6_PLA_Draft_Print.inst.cfg +++ b/resources/quality/ultimaker_s5/um_s5_cc0.6_PLA_Draft_Print.inst.cfg @@ -34,6 +34,4 @@ speed_wall = =math.ceil(speed_print * 40 / 45) speed_wall_x = =speed_wall speed_wall_0 = =math.ceil(speed_wall * 35 / 40) support_angle = 70 -support_pattern = ='triangles' -support_xy_distance = =wall_line_width_0 * 1.5 top_bottom_thickness = =layer_height * 4 diff --git a/resources/variants/ultimaker_s5_bb0.8.inst.cfg b/resources/variants/ultimaker_s5_bb0.8.inst.cfg index 901391d034..bf5802de0d 100644 --- a/resources/variants/ultimaker_s5_bb0.8.inst.cfg +++ b/resources/variants/ultimaker_s5_bb0.8.inst.cfg @@ -16,8 +16,6 @@ acceleration_prime_tower = =math.ceil(acceleration_print * 200 / 3500) brim_width = 3 cool_fan_speed = 50 cool_min_speed = 5 -gradual_support_infill_step_height = 1.6 -gradual_support_infill_steps = 2 infill_overlap = 0 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles' infill_wipe_dist = 0 @@ -57,19 +55,6 @@ speed_support_bottom = =math.ceil(speed_support_interface * 10 / 20) speed_wall_0 = =math.ceil(speed_wall * 25 / 30) speed_prime_tower = =math.ceil(speed_print * 7 / 35) support_angle = 60 -support_bottom_height = =layer_height * 2 -support_bottom_pattern = zigzag -support_bottom_stair_step_height = 0 -support_infill_rate = 50 -support_infill_sparse_thickness = 0.4 -support_interface_enable = True -support_interface_height = 0.6 -support_interface_skip_height = =layer_height -support_join_distance = 3 -support_offset = 1.5 -support_use_towers = False -support_xy_distance = =wall_line_width_0 -support_xy_distance_overhang = =wall_line_width_0 / 4 support_z_distance = 0 switch_extruder_prime_speed = 15 switch_extruder_retraction_amount = 12 |