diff options
Diffstat (limited to 'resources/definitions/tronxy_x5sa_500.def.json')
-rw-r--r-- | resources/definitions/tronxy_x5sa_500.def.json | 13 |
1 files changed, 5 insertions, 8 deletions
diff --git a/resources/definitions/tronxy_x5sa_500.def.json b/resources/definitions/tronxy_x5sa_500.def.json index b68a954115..44f8d1ba1a 100644 --- a/resources/definitions/tronxy_x5sa_500.def.json +++ b/resources/definitions/tronxy_x5sa_500.def.json @@ -1,11 +1,10 @@ { - "name": "Tronxy X5SA/X5ST/Pro 500", + "name": "Tronxy X5SA/X5ST/Pro/2E 500mm", "version": 2, "inherits": "tronxy_x", "metadata": { "quality_definition": "tronxy_x", "visible": true, - "author": "AdderMk2", "platform": "tronxy.stl" }, "overrides": { @@ -21,13 +20,11 @@ ] }, "gantry_height": { "value": 40 }, + "retraction_amount": { "value": 6.5 }, - "machine_start_gcode": { "default_value": "; X5SA Start Code\nG21\nG90\nM82\nM107 T0\nM140 S{material_bed_temperature_layer_0}\nM104 S{material_print_temperature_layer_0} T0\nM190 S{material_bed_temperature_layer_0}\nM109 S{material_print_temperature_layer_0} T0\nG28\nG92 E0\n "}, - "machine_end_gcode": { "default_value": "G91 ;Relative positioning\nG1 E-2 F2700 \nG1 E-2 Z0.2 F2400 \nG1 X5 Y5 F3000\nG1 Z10\nG90\n\nG1 X0 Y0 \nM106 S0\nM104 S0\nM140 S0\n\nM84 X Y E \n" }, + "machine_start_gcode": { "default_value": "; X5SA Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y290 F1500.0 E15 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E30 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n"}, + "machine_end_gcode": { "default_value": "G91 ; Set Positioning to Relative\nM83 ; Set Extruder to Relative\nG92 E0 ; Reset Extruder\nG1 E-4 F3000 ; Retract 4mm of filament\nG1 Z0.2 ; Raise nozzle .2mm\nG90 ; Set positioning to absolute\nG1 X{machine_width} Y{machine_depth} ; Park print head\nG91 ; Set Positioning to RelativeG1 Z10 ; Raise nozzle 10mm\nM106 S0 ; Turn off part fan\nM104 S0 ; Set nozzle temp to zero\nM140 S0 ; set bed temp to zero\nM84 X Y Z E ; Disable X Y Z and E steppers\n" }, - "machine_max_feedrate_x": { "value": 150 }, - "machine_max_feedrate_y": { "value": 150 }, - "machine_max_feedrate_z": { "value": 20 }, - "machine_max_feedrate_e": { "value": 120 } + "machine_acceleration": { "value": 150 } } } |