diff options
Diffstat (limited to 'resources/definitions')
-rw-r--r-- | resources/definitions/Mark2_for_Ultimaker2.def.json | 2 | ||||
-rw-r--r-- | resources/definitions/elegoo_neptune_2D.def.json | 12 |
2 files changed, 7 insertions, 7 deletions
diff --git a/resources/definitions/Mark2_for_Ultimaker2.def.json b/resources/definitions/Mark2_for_Ultimaker2.def.json index b23b4d0035..6ecc6bbda3 100644 --- a/resources/definitions/Mark2_for_Ultimaker2.def.json +++ b/resources/definitions/Mark2_for_Ultimaker2.def.json @@ -159,7 +159,7 @@ "acceleration_wall": { "value": "math.ceil(acceleration_print * 1000 / 4000)" }, "acceleration_wall_0": { "value": "math.ceil(acceleration_wall * 500 / 1000)" }, "jerk_enabled": { "value": true }, - "jerk_print": { "value": 12 }, + "jerk_print": {"value": 12 }, "jerk_travel": { "value": "jerk_print if magic_spiralize else 20" diff --git a/resources/definitions/elegoo_neptune_2D.def.json b/resources/definitions/elegoo_neptune_2D.def.json index ede0eb166c..be784223f2 100644 --- a/resources/definitions/elegoo_neptune_2D.def.json +++ b/resources/definitions/elegoo_neptune_2D.def.json @@ -32,10 +32,10 @@ "machine_extruders_share_nozzle": {"default_value": true}, "machine_always_write_active_tool": {"default_value": true}, "prime_blob_enable": {"default_value": false}, - "prime_tower_enable": {"default_value": true}, - "prime_tower_size": {"default_value": 30}, - "prime_tower_min_volume": {"default_value": 90}, - "speed_print": { "value": 60.0 }, + "prime_tower_enable": {"default_value": true}, + "prime_tower_size": {"default_value": 30}, + "prime_tower_min_volume": {"default_value": 90}, + "speed_print": { "value": 60.0 }, "z_seam_type":{"default_value": "back"}, "z_seam_corner":{"default_value": "z_seam_corner_weighted"}, "material_standby_temperature":{"default_value": 200,"settable_per_extruder": false}, @@ -46,8 +46,8 @@ "raft_margin":{"default_value": 5}, "raft_airgap":{"default_value": 0.25}, "brim_width":{"default_value": 5}, - "skin_angles":{"default_value": [45, 135]}, - "infill_pattern":{"default_value": "gyroid"}, + "skin_angles":{"default_value": [45, 135]}, + "infill_pattern":{"value": "gyroid"}, "machine_gcode_flavor": {"default_value": "RepRap (Marlin/Sprinter)"}, "machine_start_gcode": {"default_value": ";simage\n;gimage\nG28 ;home\n;G29 ;Run ABL\n;M420 S1 ;Enable ABL mesh\nG92 E0 ;Reset Extruder\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X2.0 Y20 Z0.28 F5000.0 ;Move to start position\nG1 E90 F1200 ;Load filament\nG92 E0 ;Reset Extruder\nG1 X2.0 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X2.3 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X2.3 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up"}, "machine_end_gcode": {"default_value": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-80 Z0.2 F1600 ;Retract and raise Z\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positionning\nG1 X0 Y{machine_depth} ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z"} |