diff options
Diffstat (limited to 'resources/i18n/fi_FI/fdmprinter.def.json.po')
| -rw-r--r-- | resources/i18n/fi_FI/fdmprinter.def.json.po | 92 |
1 files changed, 85 insertions, 7 deletions
diff --git a/resources/i18n/fi_FI/fdmprinter.def.json.po b/resources/i18n/fi_FI/fdmprinter.def.json.po index 6a4e7390ad..26860c7019 100644 --- a/resources/i18n/fi_FI/fdmprinter.def.json.po +++ b/resources/i18n/fi_FI/fdmprinter.def.json.po @@ -7,7 +7,7 @@ msgid "" msgstr "" "Project-Id-Version: Cura 3.6\n" "Report-Msgid-Bugs-To: r.dulek@ultimaker.com\n" -"POT-Creation-Date: 2018-10-29 15:01+0000\n" +"POT-Creation-Date: 2019-02-26 16:36+0000\n" "PO-Revision-Date: 2017-09-27 12:27+0200\n" "Last-Translator: Bothof <info@bothof.nl>\n" "Language-Team: Finnish\n" @@ -1669,7 +1669,7 @@ msgstr "Pintakalvon limityksen prosentti" #: fdmprinter.def.json msgctxt "skin_overlap description" -msgid "The amount of overlap between the skin and the walls as a percentage of the skin line width. A slight overlap allows the walls to connect firmly to the skin. This is a percentage of the average line widths of the skin lines and the innermost wall." +msgid "Adjust the amount of overlap between the walls and (the endpoints of) the skin-centerlines, as a percentage of the line widths of the skin lines and the innermost wall. A slight overlap allows the walls to connect firmly to the skin. Note that, given an equal skin and wall line-width, any percentage over 50% may already cause any skin to go past the wall, because at that point the position of the nozzle of the skin-extruder may already reach past the middle of the wall." msgstr "" #: fdmprinter.def.json @@ -1679,8 +1679,8 @@ msgstr "Pintakalvon limitys" #: fdmprinter.def.json msgctxt "skin_overlap_mm description" -msgid "The amount of overlap between the skin and the walls. A slight overlap allows the walls to connect firmly to the skin." -msgstr "Limityksen määrä pintakalvon ja seinämien välillä. Pienellä limityksellä seinämät liittyvät tukevasti pintakalvoon." +msgid "Adjust the amount of overlap between the walls and (the endpoints of) the skin-centerlines. A slight overlap allows the walls to connect firmly to the skin. Note that, given an equal skin and wall line-width, any value over half the width of the wall may already cause any skin to go past the wall, because at that point the position of the nozzle of the skin-extruder may already reach past the middle of the wall." +msgstr "" #: fdmprinter.def.json msgctxt "infill_wipe_dist label" @@ -2119,8 +2119,8 @@ msgstr "Suuttimen vaihdon takaisinvetoetäisyys" #: fdmprinter.def.json msgctxt "switch_extruder_retraction_amount description" -msgid "The amount of retraction: Set at 0 for no retraction at all. This should generally be the same as the length of the heat zone." -msgstr "Takaisinvedon määrä: 0 tarkoittaa, että takaisinvetoa ei ole lainkaan. Tämän on yleensä oltava sama kuin lämpöalueen pituus." +msgid "The amount of retraction when switching extruders. Set to 0 for no retraction at all. This should generally be the same as the length of the heat zone." +msgstr "" #: fdmprinter.def.json msgctxt "switch_extruder_retraction_speeds label" @@ -2779,7 +2779,7 @@ msgstr "Pyyhkäisytila" #: fdmprinter.def.json msgctxt "retraction_combing description" -msgid "Combing keeps the nozzle within already printed areas when traveling. This results in slightly longer travel moves but reduces the need for retractions. If combing is off, the material will retract and the nozzle moves in a straight line to the next point. It is also possible to avoid combing over top/bottom skin areas and also to only comb within the infill. Note that the 'Within Infill' option behaves exactly like the 'Not in Skin' option in earlier Cura releases." +msgid "Combing keeps the nozzle within already printed areas when traveling. This results in slightly longer travel moves but reduces the need for retractions. If combing is off, the material will retract and the nozzle moves in a straight line to the next point. It is also possible to avoid combing over top/bottom skin areas or to only comb within the infill." msgstr "" #: fdmprinter.def.json @@ -3433,6 +3433,16 @@ msgid "The height of support infill of a given density before switching to half msgstr "Tietyn tiheysarvon tuen täytön korkeus ennen puoleen tiheyteen vaihtamista." #: fdmprinter.def.json +msgctxt "minimum_support_area label" +msgid "Minimum Support Area" +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_support_area description" +msgid "Minimum area size for support polygons. Polygons which have an area smaller than this value will not be generated." +msgstr "" + +#: fdmprinter.def.json msgctxt "support_interface_enable label" msgid "Enable Support Interface" msgstr "Ota tukiliittymä käyttöön" @@ -3658,6 +3668,66 @@ msgid "Zig Zag" msgstr "Siksak" #: fdmprinter.def.json +msgctxt "minimum_interface_area label" +msgid "Minimum Support Interface Area" +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_interface_area description" +msgid "Minimum area size for support interface polygons. Polygons which have an area smaller than this value will not be generated." +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_roof_area label" +msgid "Minimum Support Roof Area" +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_roof_area description" +msgid "Minimum area size for the roofs of the support. Polygons which have an area smaller than this value will not be generated." +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_bottom_area label" +msgid "Minimum Support Floor Area" +msgstr "" + +#: fdmprinter.def.json +msgctxt "minimum_bottom_area description" +msgid "Minimum area size for the floors of the support. Polygons which have an area smaller than this value will not be generated." +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_interface_offset label" +msgid "Support Interface Horizontal Expansion" +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_interface_offset description" +msgid "Amount of offset applied to the support interface polygons." +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_roof_offset label" +msgid "Support Roof Horizontal Expansion" +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_roof_offset description" +msgid "Amount of offset applied to the roofs of the support." +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_bottom_offset label" +msgid "Support Floor Horizontal Expansion" +msgstr "" + +#: fdmprinter.def.json +msgctxt "support_bottom_offset description" +msgid "Amount of offset applied to the floors of the support." +msgstr "" + +#: fdmprinter.def.json msgctxt "support_fan_enable label" msgid "Fan Speed Override" msgstr "" @@ -5693,6 +5763,14 @@ msgctxt "mesh_rotation_matrix description" msgid "Transformation matrix to be applied to the model when loading it from file." msgstr "Mallissa käytettävä muunnosmatriisi, kun malli ladataan tiedostosta." +#~ msgctxt "skin_overlap_mm description" +#~ msgid "The amount of overlap between the skin and the walls. A slight overlap allows the walls to connect firmly to the skin." +#~ msgstr "Limityksen määrä pintakalvon ja seinämien välillä. Pienellä limityksellä seinämät liittyvät tukevasti pintakalvoon." + +#~ msgctxt "switch_extruder_retraction_amount description" +#~ msgid "The amount of retraction: Set at 0 for no retraction at all. This should generally be the same as the length of the heat zone." +#~ msgstr "Takaisinvedon määrä: 0 tarkoittaa, että takaisinvetoa ei ole lainkaan. Tämän on yleensä oltava sama kuin lämpöalueen pituus." + #~ msgctxt "infill_pattern option concentric_3d" #~ msgid "Concentric 3D" #~ msgstr "Samankeskinen 3D" |