diff options
Diffstat (limited to 'resources/quickprint/lulzbot_TAZ_5_035nozzle/ABS/Low/profile.ini')
| -rw-r--r-- | resources/quickprint/lulzbot_TAZ_5_035nozzle/ABS/Low/profile.ini | 260 |
1 files changed, 260 insertions, 0 deletions
diff --git a/resources/quickprint/lulzbot_TAZ_5_035nozzle/ABS/Low/profile.ini b/resources/quickprint/lulzbot_TAZ_5_035nozzle/ABS/Low/profile.ini new file mode 100644 index 0000000000..8cb8b287cb --- /dev/null +++ b/resources/quickprint/lulzbot_TAZ_5_035nozzle/ABS/Low/profile.ini @@ -0,0 +1,260 @@ +[info] +name = Fast Print +order = 0 + +[profile] +layer_height = .28 +wall_thickness = 1.05 +retraction_enable = True +solid_layer_thickness = .84 +fill_density = 20 +nozzle_size = .35 +print_speed = 50 +print_temperature = 0 +print_temperature2 = 0 +print_temperature3 = 0 +print_temperature4 = 0 +print_bed_temperature = 0 +support = None +platform_adhesion = None +support_dual_extrusion = Both +wipe_tower = False +wipe_tower_volume = 15 +ooze_shield = False +filament_diameter = 2.85 +filament_diameter2 = 0 +filament_diameter3 = 0 +filament_diameter4 = 0 +filament_flow = 100.0 +retraction_speed = 10 +retraction_amount = 1 +retraction_dual_amount = 16.5 +retraction_min_travel = 0.5 +retraction_combing = True +retraction_minimal_extrusion = 0.005 +retraction_hop = 0.1 +bottom_thickness = .3 +layer0_width_factor = 125 +object_sink = 0.0 +overlap_dual = 0.15 +travel_speed = 175 +bottom_layer_speed = 15 +infill_speed = 60 +inset0_speed = 50 +insetx_speed = 55 +cool_min_layer_time = 15 +fan_enabled = True +skirt_line_count = 1 +skirt_gap = 3.0 +skirt_minimal_length = 250 +fan_full_height = 0.5 +fan_speed = 40 +fan_speed_max = 60 +cool_min_feedrate = 10 +cool_head_lift = False +solid_top = True +solid_bottom = True +fill_overlap = 15 +support_type = Lines +support_angle = 45 +support_fill_rate = 30 +support_xy_distance = 0.7 +support_z_distance = 0.05 +spiralize = False +simple_mode = False +brim_line_count = 10 +raft_margin = 5.0 +raft_line_spacing = 3.0 +raft_base_thickness = 0.3 +raft_base_linewidth = 1.0 +raft_interface_thickness = 0.27 +raft_interface_linewidth = 0.4 +raft_airgap = 0.22 +raft_surface_layers = 2 +fix_horrible_union_all_type_a = True +fix_horrible_union_all_type_b = False +fix_horrible_use_open_bits = False +fix_horrible_extensive_stitching = False +plugin_config = +object_center_x = -1 +object_center_y = -1 + +[alterations] +start.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M109 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M82 ;set extruder to absolute mode + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed};move the platform down 15mm + G92 E0 ; zero the extruded length + G1 F200 E0 ; extrude 3mm of feed stock + G92 E0 ; zero the extruded length again + G1 F{travel_speed} ; set travel speed + M203 X192 Y208 Z3 ; speed limits + M117 Printing... ; send message to LCD + +end.gcode = M400 ; wait for buffer to clear + M104 S0 ; hotend off + M140 S0 ; heated bed heater off (if you have it) + M107 ; fans off + G91 ; relative positioning + G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more + G90 ; absolute positioning + G1 X0 Y250 ; move to cooling position + M84 ; steppers off + G90 ; absolute positioning + M117 TAZ Ready. + ;{profile_string} + +start2.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end2.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +start3.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T2 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end3.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M104 T2 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +start4.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T3 ;Switch to the 4th extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T2 ;Switch to the 3th extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end4.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M104 T2 S0 ;extruder heater off + M104 T3 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +support_start.gcode = +support_end.gcode = +cool_start.gcode = +cool_end.gcode = +replace.csv = +preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. + ;This code is added before the T(n) +postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. + ;This code is added after the T(n) + |