{
    "version": 2,
    "name": "fusedform_base",
    "inherits": "fdmprinter",
    "metadata": {
        "author": "Juan Blanco",
        "manufacturer": "Fused Form",
        "visible": false,
        "machine_extruder_trains":{"0": "fusedform_base_extruder_0"},
	"preferred_material": "generic_pla",
        "exclude_materials": [ "structur3d_dap100silicone" ],
	"has_machine_quality": true,
	"has_materials": true,
        "preferred_quality_type": "normal"
    },

    "overrides": {
        "machine_heated_bed": { "default_value": true },
        "machine_center_is_zero": {"default_value": false},
        "machine_head_with_fans_polygon":{"default_value": [
                [ -20, 20 ],
                [ -20, -20 ],
                [ 18, 20 ],
                [ 18, -18 ]
            ]
        },
        "gantry_height": {"value": "70"},

        "machine_use_extruder_offset_to_offset_coords": {"default_value": true},
	"machine_gcode_flavor": {"default_value": "RepRap (Marlin/Sprinter)"},
        "machine_start_gcode": {"default_value": "G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F9000 ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E6 ;extrude 6 mm of feed stock\nG92 E0 ;zero the extruded length again\n;Put printing message on LCD screen\nM117 Printing..."},
        "machine_end_gcode": {"value": "'M104 S0 ;extruder heater off' + ('\\nM140 S0 ;heated bed heater off' if machine_heated_bed else '') + '\\nG91 ;relative positioning\\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\\nM84 ;steppers off\\nG90 ;absolute positioning\\nM107 ; Fans off'"},
	
	"layer_height": { "default_value": 0.15 },
	"layer_height_0": { "default_value": 0.2 },

	"wall_line_count":{ "value": 3 },
	"wall_thickness": { "value": 1.2 },
 	"top_bottom_thickness": {"value": 1.5},
 	"optimize_wall_printing_order": {"value": true},

	"infill_sparse_density": {"value":15},
 	"infill_overlap": {"value": 0},

	"speed_print": { "value": 45 },
	"speed_infill": { "value": 45 },
	"speed_travel": { "value": 75 },
 	"speed_topbottom": {"value": 40 },
	"speed_wall": { "value": 35 },
	"speed_wall_x": { "value": 40 },

 	"retraction_enable": {"default_value":true},
	"retraction_amount": { "default_value": 4 },
        "retraction_speed": { "default_value": 70},
 	"retraction_min_travel": {"value":5 },
	"retraction_count_max": {"default_value":10 },
	"retraction_extrusion_window": {"value":4 },
 	"retraction_hop": {"default_value":0.2},
	"retraction_hop_enabled": {"value":true},
	"speed_z_hop": {"value":2.5 },

 	"cool_fan_enabled": {"default_value":true},
 	"cool_fan_full_at_height": {"value":0.4},
 	"cool_fan_full_layer": {"value":2},
 	"cool_min_speed": {"value":30},

	"support_enable": {"value":true},
 	"support_angle": {"default_value": 50},
 	"support_brim_enable": {"value":true},
 	"support_infill_angles": {"value":[-45]},
 	"support_interface_density": {"value": 70},
 	"support_interface_enable": {"value": true },
	"support_interface_height": {"value": 0.5},
 	"support_interface_pattern": {"default_value":"lines"},
 	"support_pattern": {"default_value":"lines"},
 	"support_xy_distance": {"value": 0.5},
 	"support_z_distance": {"value": 0.3 },


 	"adhesion_type": {"default_value":"skirt"}
    }
}