{
    "version": 2,
    "name": "Renkforce RF100 XL",
    "inherits": "fdmprinter",
    "metadata": {
        "author": "Simon Peter (based on RF100.ini by Conrad Electronic SE)",
        "file_formats": "text/x-gcode",
        "manufacturer": "Renkforce",
        "visible": true,
        "machine_extruder_trains":
        {
            "0": "renkforce_rf100_xl_extruder_0"
        }
    },

    "overrides": {
        "adhesion_type": {
            "default_value": "skirt"
        },
        "bottom_thickness": {
            "value": "0.6"
        },
        "brim_width": {
            "value": "3.0"
        },
        "cool_fan_enabled": {
            "value": "True"
        },
        "cool_fan_full_at_height": {
            "value": "0.5"
        },
        "cool_fan_speed_max": {
            "value": "100.0"
        },
        "cool_fan_speed_min": {
            "value": "100.0"
        },
        "cool_lift_head": {
            "value": "True"
        },
        "cool_min_layer_time": {
            "value": "1.0"
        },
        "cool_min_speed": {
            "value": "5.0"
        },
        "infill_before_walls": {
            "value": "True"
        },
        "infill_line_width": {
            "value": "0.6"
        },
        "infill_overlap": {
            "value": "15.0"
        },
        "infill_sparse_density": {
            "value": "26.0"
        },
        "ironing_enabled": {
            "value": "True"
        },
        "layer_0_z_overlap": {
            "value": "0.11"
        },
        "layer_height_0": {
            "value": "0.3"
        },
        "machine_depth": {
            "value": "200"
        },
        "machine_end_gcode": {
            "default_value": ";End GCode\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-4 F300 ;move Z up a bit and retract filament even more\nM104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG0 Z{machine_height} F1800 ;move the platform all the way down\nG28 X0 Y0 F1800 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning\nM117 Done"
        },
        "machine_gcode_flavor": {
            "default_value": "RepRap (Marlin/Sprinter)"
        },
        "machine_heated_bed": {
            "default_value": "true"
        },
        "machine_height": {
            "value": "200"
        },
        "machine_name": {
            "default_value": "Renkforce RF100 XL"
        },
        "machine_start_gcode": {
            "default_value": ";Sliced at: {day} {date} {time}\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG1 Z5.0 F1800 ;move Z to 5mm\nG28 X0 Y0 F1800 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstop\nG92 E0 ;zero the extruded length\nG1 F200 E6.0 ;extrude 6.0mm of feed stock to build pressure\nG1 Z5.0 F300 ;move the platform down 5mm\nG92 E0 ;zero the extruded length again\nG1 F1800\n;Put printing message on LCD screen\nM117 Printing..."
        },
        "machine_width": {
            "value": "200"
        },
        "material_bed_temperature": {
            "value": "70"
        },
        "material_print_temperature": {
            "value": "210.0"
        },
        "ooze_shield_enabled": {
            "value": "True"
        },
        "raft_airgap": {
            "value": "0.33"
        },
        "raft_base_line_spacing": {
            "value": "3.0"
        },
        "raft_base_line_width": {
            "value": "1.0"
        },
        "raft_base_thickness": {
            "value": "0.3"
        },
        "raft_interface_line_spacing": {
            "value": "3.0"
        },
        "raft_interface_line_width": {
            "value": "0.4"
        },
        "raft_interface_thickness": {
            "value": "0.27"
        },
        "raft_margin": {
            "value": "6.0"
        },
        "raft_speed": {
            "value": "20.0"
        },
        "raft_surface_layers": {
            "value": "2"
        },
        "raft_surface_line_spacing": {
            "value": "0.4"
        },
        "raft_surface_line_width": {
            "value": "0.4"
        },
        "raft_surface_thickness": {
            "value": "0.1"
        },
        "retraction_amount": {
            "value": "5.0"
        },
        "retraction_combing": {
            "value": "'all'"
        },
        "retraction_enable": {
            "value": "True"
        },
        "retraction_min_travel": {
            "value": "1.5"
        },
        "skin_overlap": {
            "value": "15.0"
        },
        "skirt_brim_minimal_length": {
            "value": "150.0"
        },
        "skirt_gap": {
            "value": "3.0"
        },
        "skirt_line_count": {
            "value": "3"
        },
        "speed_infill": {
            "value": "50.0"
        },
        "speed_layer_0": {
            "value": "15.0"
        },
        "speed_print": {
            "value": "50.0"
        },
        "speed_topbottom": {
            "value": "30.0"
        },
        "speed_travel": {
            "value": "50.0"
        },
        "speed_wall_0": {
            "value": "25.0"
        },
        "speed_wall_x": {
            "value": "35.0"
        },
        "support_angle": {
            "value": "60.0"
        },
        "support_enable": {
            "value": "False"
        },
        "support_infill_rate": {
            "value": "15 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 15"
        },
        "support_line_width": {
            "value": "0.6"
        },
        "support_pattern": {
            "default_value": "lines"
        },
        "support_type": {
            "default_value": "everywhere"
        },
        "support_xy_distance": {
            "value": "0.7"
        },
        "support_z_distance": {
            "value": "0.35"
        },
        "top_bottom_thickness": {
            "value": "0.8"
        },
        "wall_thickness": {
            "value": "0.8"
        }
    }
}