1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
{
"version": 2,
"name": "fusedform_base",
"inherits": "fdmprinter",
"metadata": {
"author": "Juan Blanco",
"manufacturer": "Fused Form",
"visible": false,
"machine_extruder_trains":{"0": "fusedform_base_extruder_0"},
"preferred_material": "generic_pla",
"exclude_materials": [ "structur3d_dap100silicone" ],
"has_machine_quality": true,
"has_materials": true,
"preferred_quality_type": "normal"
},
"overrides": {
"machine_heated_bed": { "default_value": true },
"machine_center_is_zero": {"default_value": false},
"machine_head_with_fans_polygon":{"default_value": [
[ -20, 20 ],
[ -20, -20 ],
[ 18, 20 ],
[ 18, -18 ]
]
},
"gantry_height": {"value": "70"},
"machine_use_extruder_offset_to_offset_coords": {"default_value": true},
"machine_gcode_flavor": {"default_value": "RepRap (Marlin/Sprinter)"},
"machine_start_gcode": {"default_value": "G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F9000 ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E6 ;extrude 6 mm of feed stock\nG92 E0 ;zero the extruded length again\n;Put printing message on LCD screen\nM117 Printing..."},
"machine_end_gcode": {"value": "'M104 S0 ;extruder heater off' + ('\\nM140 S0 ;heated bed heater off' if machine_heated_bed else '') + '\\nG91 ;relative positioning\\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\\nM84 ;steppers off\\nG90 ;absolute positioning\\nM107 ; Fans off'"},
"layer_height": { "default_value": 0.15 },
"layer_height_0": { "default_value": 0.2 },
"wall_line_count":{ "value": 3 },
"wall_thickness": { "value": 1.2 },
"top_bottom_thickness": {"value": 1.5},
"optimize_wall_printing_order": {"value": true},
"infill_sparse_density": {"value":15},
"infill_overlap": {"value": 0},
"speed_print": { "value": 45 },
"speed_infill": { "value": 45 },
"speed_travel": { "value": 75 },
"speed_topbottom": {"value": 40 },
"speed_wall": { "value": 35 },
"speed_wall_x": { "value": 40 },
"retraction_enable": {"default_value":true},
"retraction_amount": { "default_value": 4 },
"retraction_speed": { "default_value": 70},
"retraction_min_travel": {"value":5 },
"retraction_count_max": {"default_value":10 },
"retraction_extrusion_window": {"value":4 },
"retraction_hop": {"default_value":0.2},
"retraction_hop_enabled": {"value":true},
"speed_z_hop": {"value":2.5 },
"cool_fan_enabled": {"default_value":true},
"cool_fan_full_at_height": {"value":0.4},
"cool_fan_full_layer": {"value":2},
"cool_min_speed": {"value":30},
"support_enable": {"value":true},
"support_angle": {"default_value": 50},
"support_brim_enable": {"value":true},
"support_infill_angles": {"value":[-45]},
"support_interface_density": {"value": 70},
"support_interface_enable": {"value": true },
"support_interface_height": {"value": 0.5},
"support_interface_pattern": {"default_value":"lines"},
"support_pattern": {"default_value":"lines"},
"support_xy_distance": {"value": 0.5},
"support_z_distance": {"value": 0.3 },
"adhesion_type": {"default_value":"skirt"}
}
}
|
