diff options
| -rw-r--r-- | README.markdown | 2 | ||||
| -rw-r--r-- | lib/Slic3r/Config.pm | 8 | ||||
| -rw-r--r-- | lib/Slic3r/GCode.pm | 6 | ||||
| -rw-r--r-- | lib/Slic3r/GUI/Tab.pm | 2 | ||||
| -rwxr-xr-x | slic3r.pl | 2 |
5 files changed, 16 insertions, 4 deletions
diff --git a/README.markdown b/README.markdown index 7a9553340..67a4e7d0a 100644 --- a/README.markdown +++ b/README.markdown @@ -144,6 +144,8 @@ The author of the Silk icon set is Mark James. (default: 60) --top-solid-infill-speed Speed of print moves for top surfaces in mm/s or % over solid infill speed (default: 50) + --support-material-speed + Speed of support material print moves in mm/s (default: 60) --bridge-speed Speed of bridge print moves in mm/s (default: 60) --gap-fill-speed Speed of gap fill print moves in mm/s (default: 20) --first-layer-speed Speed of print moves for bottom layer, expressed either as an absolute diff --git a/lib/Slic3r/Config.pm b/lib/Slic3r/Config.pm index 6ef3d8ca6..85b1c0149 100644 --- a/lib/Slic3r/Config.pm +++ b/lib/Slic3r/Config.pm @@ -284,6 +284,14 @@ our $Options = { ratio_over => 'solid_infill_speed', default => 50, }, + 'support_material_speed' => { + label => 'Support material', + tooltip => 'Speed for printing support material.', + sidetext => 'mm/s', + cli => 'support-material-speed=f', + type => 'f', + default => 60, + }, 'bridge_speed' => { label => 'Bridges', tooltip => 'Speed for printing bridges.', diff --git a/lib/Slic3r/GCode.pm b/lib/Slic3r/GCode.pm index 5cb86e56a..bc5c32905 100644 --- a/lib/Slic3r/GCode.pm +++ b/lib/Slic3r/GCode.pm @@ -36,7 +36,7 @@ has 'speeds' => ( default => sub {+{ map { $_ => 60 * $Slic3r::Config->get_value("${_}_speed") } qw(travel perimeter small_perimeter external_perimeter infill - solid_infill top_solid_infill bridge gap_fill), + solid_infill top_solid_infill support_material bridge), }}, ); @@ -51,8 +51,8 @@ my %role_speeds = ( &EXTR_ROLE_TOPSOLIDFILL => 'top_solid_infill', &EXTR_ROLE_BRIDGE => 'bridge', &EXTR_ROLE_SKIRT => 'perimeter', - &EXTR_ROLE_SUPPORTMATERIAL => 'perimeter', - &EXTR_ROLE_GAPFILL => 'gap_fill', + &EXTR_ROLE_SUPPORTMATERIAL => 'support_material', + &EXTR_ROLE_GAPFILL => 'solid_infill', ); sub set_shift { diff --git a/lib/Slic3r/GUI/Tab.pm b/lib/Slic3r/GUI/Tab.pm index 31e2e103b..bc215a049 100644 --- a/lib/Slic3r/GUI/Tab.pm +++ b/lib/Slic3r/GUI/Tab.pm @@ -420,7 +420,7 @@ sub build { $self->add_options_page('Speed', 'time.png', optgroups => [ { title => 'Speed for print moves', - options => [qw(perimeter_speed small_perimeter_speed external_perimeter_speed infill_speed solid_infill_speed top_solid_infill_speed bridge_speed gap_fill_speed)], + options => [qw(perimeter_speed small_perimeter_speed external_perimeter_speed infill_speed solid_infill_speed top_solid_infill_speed support_material_speed bridge_speed gap_fill_speed)], }, { title => 'Speed for non-print moves', @@ -192,6 +192,8 @@ $j (default: $config->{solid_infill_speed}) --top-solid-infill-speed Speed of print moves for top surfaces in mm/s or % over solid infill speed (default: $config->{top_solid_infill_speed}) + --support-material-speed + Speed of support material print moves in mm/s (default: $config->{support_material_speed}) --bridge-speed Speed of bridge print moves in mm/s (default: $config->{bridge_speed}) --gap-fill-speed Speed of gap fill print moves in mm/s (default: $config->{gap_fill_speed}) --first-layer-speed Speed of print moves for bottom layer, expressed either as an absolute |