diff options
| -rw-r--r-- | README.markdown | 1 | ||||
| -rw-r--r-- | lib/Slic3r/Config.pm | 8 | ||||
| -rw-r--r-- | lib/Slic3r/GCode.pm | 4 | ||||
| -rwxr-xr-x | slic3r.pl | 1 |
4 files changed, 12 insertions, 2 deletions
diff --git a/README.markdown b/README.markdown index 72e961a45..7a9553340 100644 --- a/README.markdown +++ b/README.markdown @@ -145,6 +145,7 @@ The author of the Silk icon set is Mark James. --top-solid-infill-speed Speed of print moves for top surfaces in mm/s or % over solid infill speed (default: 50) --bridge-speed Speed of bridge print moves in mm/s (default: 60) + --gap-fill-speed Speed of gap fill print moves in mm/s (default: 20) --first-layer-speed Speed of print moves for bottom layer, expressed either as an absolute value or as a percentage over normal speeds (default: 30%) diff --git a/lib/Slic3r/Config.pm b/lib/Slic3r/Config.pm index b20f0ee17..6ef3d8ca6 100644 --- a/lib/Slic3r/Config.pm +++ b/lib/Slic3r/Config.pm @@ -293,6 +293,14 @@ our $Options = { aliases => [qw(bridge_feed_rate)], default => 60, }, + 'gap_fill_speed' => { + label => 'Gap fill', + tooltip => 'Speed for filling small gaps using short zigzag moves. Keep this reasonably low to avoid too much shaking and resonance issues.', + sidetext => 'mm/s', + cli => 'gap-fill-speed=f', + type => 'f', + default => 20, + }, 'first_layer_speed' => { label => 'First layer speed', tooltip => 'If expressed as absolute value in mm/s, this speed will be applied to all the print moves of the first layer, regardless of their type. If expressed as a percentage (for example: 40%) it will scale the default speeds.', diff --git a/lib/Slic3r/GCode.pm b/lib/Slic3r/GCode.pm index d11035e53..5cb86e56a 100644 --- a/lib/Slic3r/GCode.pm +++ b/lib/Slic3r/GCode.pm @@ -36,7 +36,7 @@ has 'speeds' => ( default => sub {+{ map { $_ => 60 * $Slic3r::Config->get_value("${_}_speed") } qw(travel perimeter small_perimeter external_perimeter infill - solid_infill top_solid_infill bridge), + solid_infill top_solid_infill bridge gap_fill), }}, ); @@ -52,7 +52,7 @@ my %role_speeds = ( &EXTR_ROLE_BRIDGE => 'bridge', &EXTR_ROLE_SKIRT => 'perimeter', &EXTR_ROLE_SUPPORTMATERIAL => 'perimeter', - &EXTR_ROLE_GAPFILL => 'solid_infill', + &EXTR_ROLE_GAPFILL => 'gap_fill', ); sub set_shift { @@ -193,6 +193,7 @@ $j --top-solid-infill-speed Speed of print moves for top surfaces in mm/s or % over solid infill speed (default: $config->{top_solid_infill_speed}) --bridge-speed Speed of bridge print moves in mm/s (default: $config->{bridge_speed}) + --gap-fill-speed Speed of gap fill print moves in mm/s (default: $config->{gap_fill_speed}) --first-layer-speed Speed of print moves for bottom layer, expressed either as an absolute value or as a percentage over normal speeds (default: $config->{first_layer_speed}) |