diff options
Diffstat (limited to 'Firmware/language_en.h')
| -rw-r--r-- | Firmware/language_en.h | 38 |
1 files changed, 20 insertions, 18 deletions
diff --git a/Firmware/language_en.h b/Firmware/language_en.h index ec3ea2110..a41a8698f 100644 --- a/Firmware/language_en.h +++ b/Firmware/language_en.h @@ -69,16 +69,16 @@ #define MSG_SETTINGS "Settings" #define MSG_PREHEAT "Preheat" -#define MSG_UNLOAD_FILAMENT "Unload filament" -#define MSG_LOAD_FILAMENT "Load filament" -#define MSG_LOAD_FILAMENT_1 "Load filament 1" -#define MSG_LOAD_FILAMENT_2 "Load filament 2" -#define MSG_LOAD_FILAMENT_3 "Load filament 3" -#define MSG_LOAD_FILAMENT_4 "Load filament 4" -#define MSG_UNLOAD_FILAMENT_1 "Unload filament 1" -#define MSG_UNLOAD_FILAMENT_2 "Unload filament 2" -#define MSG_UNLOAD_FILAMENT_3 "Unload filament 3" -#define MSG_UNLOAD_FILAMENT_4 "Unload filament 4" +#define(length=17) MSG_UNLOAD_FILAMENT "Unload filament" +#define(length=17) MSG_LOAD_FILAMENT "Load filament" +#define(length=17) MSG_LOAD_FILAMENT_1 "Load filament 1" +#define(length=17) MSG_LOAD_FILAMENT_2 "Load filament 2" +#define(length=17) MSG_LOAD_FILAMENT_3 "Load filament 3" +#define(length=17) MSG_LOAD_FILAMENT_4 "Load filament 4" +#define(length=17) MSG_UNLOAD_FILAMENT_1 "Unload filament 1" +#define(length=17) MSG_UNLOAD_FILAMENT_2 "Unload filament 2" +#define(length=17) MSG_UNLOAD_FILAMENT_3 "Unload filament 3" +#define(length=17) MSG_UNLOAD_FILAMENT_4 "Unload filament 4" #define MSG_UNLOAD_ALL "Unload all" #define MSG_LOAD_ALL "Load all" @@ -173,9 +173,9 @@ #define MSG_SELFTEST_ENDSTOPS "Endstops" #define MSG_SELFTEST_MOTOR "Motor" #define MSG_SELFTEST_ENDSTOP "Endstop" -#define MSG_SELFTEST_ENDSTOP_NOTHIT "Endstop not hit" +#define(length=20,lines=1) MSG_SELFTEST_ENDSTOP_NOTHIT "Endstop not hit" #define MSG_SELFTEST_OK "Self test OK" -#define MSG_LOOSE_PULLEY "Loose pulley" +#define(length=20,lines=1) MSG_LOOSE_PULLEY "Loose pulley" #define(length=20) MSG_SELFTEST_FAN "Fan test"; #define(length=20) MSG_SELFTEST_COOLING_FAN "Front print fan?"; @@ -203,7 +203,7 @@ #define MSG_HOMEYZ_PROGRESS "Calibrating Z" #define MSG_HOMEYZ_DONE "Calibration done" -#define MSG_SHOW_END_STOPS "Show end stops" +#define(length=17,lines=1) MSG_SHOW_END_STOPS "Show end stops" #define MSG_CALIBRATE_BED "Calibrate XYZ" #define MSG_CALIBRATE_BED_RESET "Reset XYZ calibr." @@ -261,14 +261,14 @@ #define(length=20, lines=8) MSG_CLEAN_NOZZLE_E "E calibration finished. Please clean the nozzle. Click when done." #define(length=20, lines=3) MSG_WAITING_TEMP "Waiting for nozzle and bed cooling" #define(length=20, lines=2) MSG_FILAMENT_CLEAN "Is color clear?" -#define(lenght=20) MSG_UNLOADING_FILAMENT "Unloading filament" +#define(lenght=18, lines=1) MSG_UNLOADING_FILAMENT "Unloading filament" #define(length=20, lines=8) MSG_PAPER "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately." #define MSG_BED_CORRECTION_MENU "Bed level correct" -#define MSG_BED_CORRECTION_LEFT "Left side um" -#define MSG_BED_CORRECTION_RIGHT "Right side um" -#define MSG_BED_CORRECTION_FRONT "Front side um" -#define MSG_BED_CORRECTION_REAR "Rear side um" +#define(length=14,lines=1) MSG_BED_CORRECTION_LEFT "Left side [um]" +#define(length=14,lines=1) MSG_BED_CORRECTION_RIGHT "Right side[um]" +#define(length=14,lines=1) MSG_BED_CORRECTION_FRONT "Front side[um]" +#define(length=14,lines=1) MSG_BED_CORRECTION_REAR "Rear side [um]" #define MSG_BED_CORRECTION_RESET "Reset" #define MSG_MESH_BED_LEVELING "Mesh Bed Leveling" @@ -292,4 +292,6 @@ #define(length=20, lines=4) MSG_TEMP_CALIBRATION_DONE "Temperature calibration is finished. Click to continue." #define(length=20, lines=1) MSG_TEMP_CALIBRATION_ON "Temp. cal. [ON]" #define(length=20, lines=1) MSG_TEMP_CALIBRATION_OFF "Temp. cal. [OFF]" +#define(length=20, lines=1) MSG_PREPARE_FILAMENT "Prepare new filament" + |