diff options
Diffstat (limited to 'Firmware/pins.h')
| -rwxr-xr-x | Firmware/pins.h | 512 |
1 files changed, 266 insertions, 246 deletions
diff --git a/Firmware/pins.h b/Firmware/pins.h index 82ee55acb..7a3de5d54 100755 --- a/Firmware/pins.h +++ b/Firmware/pins.h @@ -20,282 +20,302 @@ #define LARGE_FLASH true /***************************************************************** -* Rambo Pin Assignments 1.3 -******************************************************************/ -#if MOTHERBOARD == 302 - #define MINI-RAMBO - + * RamboBig Pin Assignments + ******************************************************************/ +#if MOTHERBOARD == 301 + +#define ELECTRONICS "RAMBoBig" + +#define KNOWN_BOARD + +#ifndef __AVR_ATmega2560__ + #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. #endif -#if MOTHERBOARD == 301 || MOTHERBOARD == 302 - #define KNOWN_BOARD - #ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. - #endif - - - #define FR_SENS 21 - - - #define X_STEP_PIN 37 - #define X_DIR_PIN 48 - #define X_MIN_PIN 12 - #define X_MAX_PIN 24 - #define X_ENABLE_PIN 29 - #define X_MS1_PIN 40 - #define X_MS2_PIN 41 - #define Y_STEP_PIN 36 - #define Y_DIR_PIN 49 - #define Y_MIN_PIN 11 - #define Y_MAX_PIN 23 - #define Y_ENABLE_PIN 28 - #define Y_MS1_PIN 69 - #define Y_MS2_PIN 39 - #define Z_STEP_PIN 35 - #define Z_DIR_PIN 47 - #define Z_MIN_PIN 10 - #define Z_MAX_PIN 30 - #define Z_ENABLE_PIN 27 - #define Z_MS1_PIN 68 - #define Z_MS2_PIN 67 - #define TEMP_BED_PIN 2 - #define TEMP_0_PIN 0 - #define HEATER_1_PIN 7 - #define TEMP_1_PIN 1 - #define TEMP_2_PIN -1 - - // The SDSS pin uses a different pin mapping from file Sd2PinMap.h + +#define FR_SENS 21 +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define TEMP_BED_PIN 2 +#define TEMP_0_PIN 0 +#define HEATER_1_PIN 7 +#define TEMP_1_PIN 1 +#define TEMP_2_PIN -1 + +// The SDSS pin uses a different pin mapping from file Sd2PinMap.h #define SDSS 53 #ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support + // these pins are defined in the SD library if building with SD support #define SCK_PIN 52 #define MISO_PIN 50 #define MOSI_PIN 51 #endif - - #define BEEPER 84 - - #define BTN_EN1 72 - #define BTN_EN2 14 - #define BTN_ENC 9 - - #define SDCARDDETECT 15 - - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - - - - #define E0_STEP_PIN 34 - #define E0_DIR_PIN 43 - #define E0_ENABLE_PIN 26 - #define E0_MS1_PIN 65 - #define E0_MS2_PIN 66 - #define LED_PIN 13 - #ifdef THREEMM_PRINTER - #define FAN_PIN 8 - #else - #define FAN_PIN 6 - #endif - #define KILL_PIN -1 //80 with Smart Controller LCD - #define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. - #define SDPOWER -1 - #ifdef BARICUDA - #define HEATER_2_PIN 6 - #else - #define HEATER_2_PIN -1 - #endif - #ifdef MINI-RAMBO - - #define ELECTRONICS "RAMBo13a" - - #define HEATER_0_PIN 3 - #define HEATER_BED_PIN 4 - #define FAN_1_PIN -1 //6 - #define PS_ON_PIN 71 - #define MOTOR_CURRENT_PWM_XY_PIN 46 - #define MOTOR_CURRENT_PWM_Z_PIN 45 - #define MOTOR_CURRENT_PWM_E_PIN 44 - - #else //RAMBo - #define ELECTRONICS "RAMBoBig" - - #define E1_STEP_PIN 33 - #define E1_DIR_PIN 42 - #define E1_ENABLE_PIN 25 - #define E1_MS1_PIN 63 - #define E1_MS2_PIN 64 - #define DIGIPOTSS_PIN 38 - #define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping - #define HEATER_0_PIN 9 - #define HEATER_BED_PIN 3 - #define PS_ON_PIN 4 - #define SDSS 53 - #ifdef ULTRA_LCD - #define KILL_PIN 80 - #ifdef NEWPANEL - //arduino pin which triggers an piezzo beeper - #define BEEPER 84 // Beeper on AUX-4 - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - //buttons are directly attached using AUX-2 - #define BTN_EN1 76 - #define BTN_EN2 77 - #define BTN_ENC 78 //the click - #define BLEN_C 2 - #define BLEN_B 1 - #define BLEN_A 0 - #define SDCARDDETECT 81 // Ramps does not use this port - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - #else //old style panel with shift register - //arduino pin witch triggers an piezzo beeper - #define BEEPER 84 //No Beeper added - //buttons are attached to a shift register - // Not wired this yet - // #define SHIFT_CLK 38 - // #define SHIFT_LD 42 - // #define SHIFT_OUT 40 - // #define SHIFT_EN 17 - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - //bits in the shift register that carry the buttons for: - // left up center down right red - #define BL_LE 7 - #define BL_UP 6 - #define BL_MI 5 - #define BL_DW 4 - #define BL_RI 3 - #define BL_ST 2 - #define BLEN_B 1 - #define BLEN_A 0 - #endif - #endif //ULTRA_LCD - #endif //RAMBo/MiniRambo option + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 +#define LED_PIN 13 + +#ifdef THREEMM_PRINTER + #define FAN_PIN 8 +#else + #define FAN_PIN 6 +#endif + +#define KILL_PIN -1 //80 with Smart Controller LCD +#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. +#define SDPOWER -1 + +#ifdef BARICUDA + #define HEATER_2_PIN 6 +#else + #define HEATER_2_PIN -1 +#endif + +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 42 +#define E1_ENABLE_PIN 25 +#define E1_MS1_PIN 63 +#define E1_MS2_PIN 64 +#define DIGIPOTSS_PIN 38 +#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping +#define HEATER_0_PIN 9 +#define HEATER_BED_PIN 3 +#define PS_ON_PIN 4 +#define SDSS 53 + +#define BEEPER 79 +#define LCD_PINS_RS 70 +#define LCD_PINS_ENABLE 71 +#define LCD_PINS_D4 72 +#define LCD_PINS_D5 73 +#define LCD_PINS_D6 74 +#define LCD_PINS_D7 75 +#define BTN_EN1 76 +#define BTN_EN2 77 +#define BTN_ENC 78 +#define BLEN_C 2 +#define BLEN_B 1 +#define BLEN_A 0 +#define SDCARDDETECT 81 +#define encrot0 0 +#define encrot1 2 +#define encrot2 3 +#define encrot3 1 + +#endif + + +/***************************************************************** +* Rambo Pin Assignments 1.3 +******************************************************************/ +#if MOTHERBOARD == 302 +#define ELECTRONICS "RAMBo13a" + +#define KNOWN_BOARD + +#ifndef __AVR_ATmega2560__ + #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. #endif +#define FR_SENS 21 +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define TEMP_BED_PIN 2 +#define TEMP_0_PIN 0 +#define HEATER_1_PIN 7 +#define TEMP_1_PIN 1 +#define TEMP_2_PIN -1 + +// The SDSS pin uses a different pin mapping from file Sd2PinMap.h +#define SDSS 53 +#ifndef SDSUPPORT + // these pins are defined in the SD library if building with SD support + #define SCK_PIN 52 + #define MISO_PIN 50 + #define MOSI_PIN 51 +#endif +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 +#define LED_PIN 13 +#ifdef THREEMM_PRINTER + #define FAN_PIN 8 +#else + #define FAN_PIN 6 +#endif +#define KILL_PIN -1 //80 with Smart Controller LCD +#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. +#define SDPOWER -1 +#ifdef BARICUDA + #define HEATER_2_PIN 6 +#else + #define HEATER_2_PIN -1 +#endif + +#define BEEPER 84 +#define BTN_EN1 72 +#define BTN_EN2 14 +#define BTN_ENC 9 +#define SDCARDDETECT 15 +#define LCD_PINS_RS 82 +#define LCD_PINS_ENABLE 18 +#define LCD_PINS_D4 19 +#define LCD_PINS_D5 70 +#define LCD_PINS_D6 85 +#define LCD_PINS_D7 71 +#define HEATER_0_PIN 3 +#define HEATER_BED_PIN 4 +#define FAN_1_PIN -1 //6 +#define PS_ON_PIN 71 + +#define MOTOR_CURRENT_PWM_XY_PIN 46 +#define MOTOR_CURRENT_PWM_Z_PIN 45 +#define MOTOR_CURRENT_PWM_E_PIN 44 + +#endif /***************************************************************** * Rambo mini Pin Assignments 1.0 ******************************************************************/ #if MOTHERBOARD == 102 - #define ELECTRONICS "RAMBo10a" - #define KNOWN_BOARD - #ifndef __AVR_ATmega2560__ +#define ELECTRONICS "RAMBo10a" + +#define KNOWN_BOARD + +#ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. - #endif +#endif - #define FR_SENS 21 - - #define LARGE_FLASH true - #define X_STEP_PIN 37 - #define X_DIR_PIN 48 - #define X_MIN_PIN 12 - #define X_MAX_PIN 24 - #define X_ENABLE_PIN 29 - #define X_MS1_PIN 40 - #define X_MS2_PIN 41 - #define Y_STEP_PIN 36 - #define Y_DIR_PIN 49 - #define Y_MIN_PIN 11 - #define Y_MAX_PIN 23 - #define Y_ENABLE_PIN 28 - #define Y_MS1_PIN 69 - #define Y_MS2_PIN 39 - #define Z_STEP_PIN 35 - #define Z_DIR_PIN 47 - #define Z_MIN_PIN 10 - #define Z_MAX_PIN 30 - #define Z_ENABLE_PIN 27 - #define Z_MS1_PIN 68 - #define Z_MS2_PIN 67 - #define TEMP_BED_PIN 2 - #define TEMP_0_PIN 0 - #define HEATER_1_PIN 7 - #define TEMP_1_PIN 1 - #define TEMP_2_PIN -1 - - // The SDSS pin uses a different pin mapping from file Sd2PinMap.h +#define FR_SENS 21 +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define TEMP_BED_PIN 2 +#define TEMP_0_PIN 0 +#define HEATER_1_PIN 7 +#define TEMP_1_PIN 1 +#define TEMP_2_PIN -1 + +// The SDSS pin uses a different pin mapping from file Sd2PinMap.h #define SDSS 53 #ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support - #define SCK_PIN 52 - #define MISO_PIN 50 - #define MOSI_PIN 51 + // these pins are defined in the SD library if building with SD support + #define SCK_PIN 52 + #define MISO_PIN 50 + #define MOSI_PIN 51 #endif - - #define BEEPER 78 - - #define BTN_EN1 80 - #define BTN_EN2 73 - #define BTN_ENC 21 - - #define SDCARDDETECT 72 - - #define LCD_PINS_RS 38 - #define LCD_PINS_ENABLE 5 - #define LCD_PINS_D4 14 - #define LCD_PINS_D5 15 - #define LCD_PINS_D6 32 - #define LCD_PINS_D7 31 - - - - #define E0_STEP_PIN 34 - #define E0_DIR_PIN 43 - #define E0_ENABLE_PIN 26 - #define E0_MS1_PIN 65 - #define E0_MS2_PIN 66 - #define LED_PIN 13 - #ifdef THREEMM_PRINTER - #define FAN_PIN 8 - #else - #define FAN_PIN 6 - #endif - #define KILL_PIN -1 //80 with Smart Controller LCD - #define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. - #define SDPOWER -1 - #ifdef BARICUDA + +#define BEEPER 78 +#define BTN_EN1 80 +#define BTN_EN2 73 +#define BTN_ENC 21 +#define SDCARDDETECT 72 +#define LCD_PINS_RS 38 +#define LCD_PINS_ENABLE 5 +#define LCD_PINS_D4 14 +#define LCD_PINS_D5 15 +#define LCD_PINS_D6 32 +#define LCD_PINS_D7 31 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 +#define LED_PIN 13 + +#ifdef THREEMM_PRINTER + #define FAN_PIN 8 +#else + #define FAN_PIN 6 +#endif + +#define KILL_PIN -1 //80 with Smart Controller LCD +#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. +#define SDPOWER -1 + +#ifdef BARICUDA #define HEATER_2_PIN 6 - #else +#else #define HEATER_2_PIN -1 - #endif +#endif + +#define HEATER_0_PIN 3 +#define HEATER_BED_PIN 4 +#define FAN_1_PIN -1 //6 +#define PS_ON_PIN 71 - #define HEATER_0_PIN 3 - #define HEATER_BED_PIN 4 - #define FAN_1_PIN -1 //6 - #define PS_ON_PIN 71 - #define MOTOR_CURRENT_PWM_XY_PIN 46 - #define MOTOR_CURRENT_PWM_Z_PIN 45 - #define MOTOR_CURRENT_PWM_E_PIN 44 - +#define MOTOR_CURRENT_PWM_XY_PIN 46 +#define MOTOR_CURRENT_PWM_Z_PIN 45 +#define MOTOR_CURRENT_PWM_E_PIN 44 #endif |