diff options
Diffstat (limited to 'Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h')
-rw-r--r-- | Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h | 245 |
1 files changed, 0 insertions, 245 deletions
diff --git a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h b/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h deleted file mode 100644 index ef288a6c5..000000000 --- a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h +++ /dev/null @@ -1,245 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm" -#define NOZZLE_TYPE "E3Dv6full" - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 310 -#define HEATER_1_MAXTEMP 310 -#define HEATER_2_MAXTEMP 310 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 210 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H |