diff options
Diffstat (limited to 'variants/1-75mm-RAMBo-10a-E3D-v6lite.h')
| -rwxr-xr-x | variants/1-75mm-RAMBo-10a-E3D-v6lite.h | 229 |
1 files changed, 229 insertions, 0 deletions
diff --git a/variants/1-75mm-RAMBo-10a-E3D-v6lite.h b/variants/1-75mm-RAMBo-10a-E3D-v6lite.h new file mode 100755 index 000000000..658c7084e --- /dev/null +++ b/variants/1-75mm-RAMBo-10a-E3D-v6lite.h @@ -0,0 +1,229 @@ +#ifndef CONFIGURATION_PRUSA_H +#define CONFIGURATION_PRUSA_H + +/*------------------------------------ + GENERAL SETTINGS +*------------------------------------*/ + +// Printer revision +#define FILAMENT_SIZE "1-75mm" +#define NOZZLE_TYPE "E3D-v6lite" + +// Printer name +#define CUSTOM_MENDEL_NAME "Prusa i3" + +// Electronics +#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 + + + +/*------------------------------------ + AXIS SETTINGS +*------------------------------------*/ + +// Steps per unit {X,Y,Z,E} +#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,174.2} + +// Endstop inverting +const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. + +// Home position +#define MANUAL_X_HOME_POS 0 +#define MANUAL_Y_HOME_POS 0 +#define MANUAL_Z_HOME_POS 0.25 + +// Travel limits after homing +#define X_MAX_POS 214 +#define X_MIN_POS 0 +#define Y_MAX_POS 198 +#define Y_MIN_POS 0 +#define Z_MAX_POS 201 +#define Z_MIN_POS 0.23 + +#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E +#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) + +#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. + +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts + + +#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) + + +/*------------------------------------ + EXTRUDER SETTINGS +*------------------------------------*/ + +// Mintemps +#define HEATER_0_MINTEMP 15 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define BED_MINTEMP 15 + +// Maxtemps +#define HEATER_0_MAXTEMP 265 +#define HEATER_1_MAXTEMP 265 +#define HEATER_2_MAXTEMP 265 +#define BED_MAXTEMP 150 + +// Define PID constants for extruder +#define DEFAULT_Kp 40.925 +#define DEFAULT_Ki 4.875 +#define DEFAULT_Kd 86.085 + +// Extrude mintemp +#define EXTRUDE_MINTEMP 190 + +// Extruder cooling fans +#define EXTRUDER_0_AUTO_FAN_PIN 8 +#define EXTRUDER_1_AUTO_FAN_PIN -1 +#define EXTRUDER_2_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + + + +/*------------------------------------ + LOAD/UNLOAD FILAMENT SETTINGS +*------------------------------------*/ + +// Load filament commands +#define LOAD_FILAMENT_0 "M83" +#define LOAD_FILAMENT_1 "G1 E70 F400" +#define LOAD_FILAMENT_2 "G1 E40 F100" + +// Unload filament commands +#define UNLOAD_FILAMENT_0 "M83" +#define UNLOAD_FILAMENT_1 "G1 E-80 F400" + +/*------------------------------------ + CHANGE FILAMENT SETTINGS +*------------------------------------*/ + +// Filament change configuration +#define FILAMENTCHANGEENABLE + #ifdef FILAMENTCHANGEENABLE + #define FILAMENTCHANGE_XPOS 211 + #define FILAMENTCHANGE_YPOS 0 + #define FILAMENTCHANGE_ZADD 2 + #define FILAMENTCHANGE_FIRSTRETRACT -2 + #define FILAMENTCHANGE_FINALRETRACT -80 + + #define FILAMENTCHANGE_FIRSTFEED 70 + #define FILAMENTCHANGE_FINALFEED 50 + #define FILAMENTCHANGE_RECFEED 5 + + #define FILAMENTCHANGE_XYFEED 70 + #define FILAMENTCHANGE_EFEED 20 + #define FILAMENTCHANGE_RFEED 400 + #define FILAMENTCHANGE_EXFEED 2 + #define FILAMENTCHANGE_ZFEED 300 + +#endif + +/*------------------------------------ + ADDITIONAL FEATURES SETTINGS +*------------------------------------*/ + +// Define Prusa filament runout sensor +//#define FILAMENT_RUNOUT_SUPPORT + +#ifdef FILAMENT_RUNOUT_SUPPORT + #define FILAMENT_RUNOUT_SENSOR 1 +#endif + +/*------------------------------------ + MOTOR CURRENT SETTINGS +*------------------------------------*/ + +// Motor Current setting for BIG RAMBo +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} + +// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range +#if MOTHERBOARD == 102 || MOTHERBOARD == 302 + #define MOTOR_CURRENT_PWM_RANGE 2000 + #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} + #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} +#endif + +/*------------------------------------ + PREHEAT SETTINGS +*------------------------------------*/ + +#define PLA_PREHEAT_HOTEND_TEMP 210 +#define PLA_PREHEAT_HPB_TEMP 50 +#define PLA_PREHEAT_FAN_SPEED 0 + +#define ABS_PREHEAT_HOTEND_TEMP 255 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 0 + +#define HIPS_PREHEAT_HOTEND_TEMP 220 +#define HIPS_PREHEAT_HPB_TEMP 100 +#define HIPS_PREHEAT_FAN_SPEED 0 + +#define PP_PREHEAT_HOTEND_TEMP 254 +#define PP_PREHEAT_HPB_TEMP 100 +#define PP_PREHEAT_FAN_SPEED 0 + +#define PET_PREHEAT_HOTEND_TEMP 240 +#define PET_PREHEAT_HPB_TEMP 90 +#define PET_PREHEAT_FAN_SPEED 0 + +#define FLEX_PREHEAT_HOTEND_TEMP 230 +#define FLEX_PREHEAT_HPB_TEMP 50 +#define FLEX_PREHEAT_FAN_SPEED 0 + + +/*------------------------------------ + THERMISTORS SETTINGS +*------------------------------------*/ + +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 110 is Pt100 with 1k pullup (non standard) + +#define TEMP_SENSOR_0 5 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_BED 1 + + +#endif //__CONFIGURATION_PRUSA_H |