msgid "" msgstr "" "Project-Id-Version: \n" "Report-Msgid-Bugs-To: \n" "POT-Creation-Date: 2018-02-28 13:53+0100\n" "PO-Revision-Date: 2018-02-28 14:13+0100\n" "Last-Translator: Oleksandra Iushchenko \n" "Language-Team: \n" "MIME-Version: 1.0\n" "Content-Type: text/plain; charset=UTF-8\n" "Content-Transfer-Encoding: 8bit\n" "X-Generator: Poedit 2.0.6\n" "Plural-Forms: nplurals=2; plural=(n != 1);\n" "Language: en\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:39 msgid "Shape" msgstr "Shape" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:46 msgid "Rectangular" msgstr "Rectangular" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:50 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1191 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:408 msgid "Size" msgstr "Size" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:51 msgid "Size in X and Y of the rectangular plate." msgstr "Size in X and Y of the rectangular plate." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:57 msgid "Origin" msgstr "Origin" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:58 msgid "" "Distance of the 0,0 G-code coordinate from the front left corner of the " "rectangle." msgstr "" "Distance of the 0,0 G-code coordinate from the front left corner of the " "rectangle." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:62 msgid "Circular" msgstr "Circular" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:65 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:129 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:200 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:211 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:325 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:336 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:355 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:434 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:781 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:801 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:860 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:878 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:896 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1044 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1052 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1094 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1103 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1113 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1121 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1129 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1215 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1421 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1491 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1527 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1704 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1711 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1718 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1727 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1737 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1747 msgid "mm" msgstr "mm" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:66 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:431 msgid "Diameter" msgstr "Diameter" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:67 msgid "" "Diameter of the print bed. It is assumed that origin (0,0) is located in the " "center." msgstr "" "Diameter of the print bed. It is assumed that origin (0,0) is located in the " "center." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:71 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:150 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:92 msgid "Custom" msgstr "Custom" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:75 msgid "Load shape from STL..." msgstr "Load shape from STL..." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:120 msgid "Settings" msgstr "Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:298 msgid "Choose a file to import bed shape from (STL/OBJ/AMF/3MF/PRUSA):" msgstr "Choose a file to import bed shape from (STL/OBJ/AMF/3MF/PRUSA):" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:315 msgid "Error! " msgstr "Error! " #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:324 msgid "The selected file contains no geometry." msgstr "The selected file contains no geometry." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:328 msgid "" "The selected file contains several disjoint areas. This is not supported." msgstr "" "The selected file contains several disjoint areas. This is not supported." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.hpp:42 msgid "Bed Shape" msgstr "Bed Shape" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:224 msgid "Array of language names and identifiers should have the same size." msgstr "Array of language names and identifiers should have the same size." #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:235 msgid "Select the language" msgstr "Select the language" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:235 msgid "Language" msgstr "Language" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:300 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:170 msgid "Default" msgstr "Default" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:325 msgid "Change Application Language" msgstr "Change Application Language" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:332 msgid "Application will be restarted" msgstr "Application will be restarted" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:332 msgid "Attention!" msgstr "Attention!" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:339 msgid "&Localization" msgstr "&Localization" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:488 #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:470 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1300 msgid "Error" msgstr "Error" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:493 msgid "Notice" msgstr "Notice" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:498 msgid "GLUquadricObjPtr | Attempt to free unreferenced scalar" msgstr "GLUquadricObjPtr | Attempt to free unreferenced scalar" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:500 msgid "Warning" msgstr "Warning" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:50 msgid "Save current " msgstr "Save current " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:51 msgid "Delete this preset" msgstr "Delete this preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:313 msgid "Layers and perimeters" msgstr "Layers and perimeters" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:314 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:777 msgid "Layer height" msgstr "Layer height" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:318 msgid "Vertical shells" msgstr "Vertical shells" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:329 msgid "Horizontal shells" msgstr "Horizontal shells" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:330 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1314 msgid "Solid layers" msgstr "Solid layers" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:335 msgid "Quality (slower slicing)" msgstr "Quality (slower slicing)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:342 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:356 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:449 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:452 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:831 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1113 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:107 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:208 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:736 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1733 msgid "Advanced" msgstr "Advanced" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:346 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:347 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:664 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:87 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:247 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:488 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:502 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:540 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:681 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:691 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:709 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:727 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:746 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1263 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1280 msgid "Infill" msgstr "Infill" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:352 msgid "Reducing printing time" msgstr "Reducing printing time" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:364 msgid "Skirt and brim" msgstr "Skirt and brim" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:365 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:146 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:88 msgid "Skirt" msgstr "Skirt" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:371 msgid "Brim" msgstr "Brim" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:374 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:375 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:191 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1030 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1380 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1387 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1399 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1409 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1417 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1432 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1453 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1464 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1480 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1489 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1498 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1509 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1525 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1533 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1534 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1543 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1551 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1565 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:147 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:89 msgid "Support material" msgstr "Support material" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:380 msgid "Raft" msgstr "Raft" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:384 msgid "Options for support material and raft" msgstr "Options for support material and raft" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:398 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:118 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:278 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:635 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:747 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:979 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1201 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1251 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1302 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1625 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:71 msgid "Speed" msgstr "Speed" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:399 msgid "Speed for print moves" msgstr "Speed for print moves" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:411 msgid "Speed for non-print moves" msgstr "Speed for non-print moves" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:414 msgid "Modifiers" msgstr "Modifiers" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:417 msgid "Acceleration control (advanced)" msgstr "Acceleration control (advanced)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:424 msgid "Autospeed (advanced)" msgstr "Autospeed (advanced)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:430 msgid "Multiple Extruders" msgstr "Multiple Extruders" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:431 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:966 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:308 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:702 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:958 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1272 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1445 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1471 msgid "Extruders" msgstr "Extruders" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:438 msgid "Ooze prevention" msgstr "Ooze prevention" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:442 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:149 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:91 msgid "Wipe tower" msgstr "Wipe tower" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:453 msgid "Extrusion width" msgstr "Extrusion width" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:463 msgid "Overlap" msgstr "Overlap" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:466 msgid "Flow" msgstr "Flow" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:469 msgid "Other" msgstr "Other" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:476 msgid "Output options" msgstr "Output options" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:477 msgid "Sequential printing" msgstr "Sequential printing" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:479 msgid "Extruder clearance (mm)" msgstr "Extruder clearance (mm)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:488 msgid "Output file" msgstr "Output file" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:494 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1001 msgid "Post-processing scripts" msgstr "Post-processing scripts" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:500 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:501 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:859 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:860 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1156 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1157 msgid "Notes" msgstr "Notes" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:507 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:867 msgid "Dependencies" msgstr "Dependencies" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:508 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:868 msgid "Profile dependencies" msgstr "Profile dependencies" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:509 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:869 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1668 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:143 msgid "Compatible printers" msgstr "Compatible printers" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:533 #, no-c-format msgid "" "The Spiral Vase mode requires:\n" "- one perimeter\n" "- no top solid layers\n" "- 0% fill density\n" "- no support material\n" "- no ensure_vertical_shell_thickness\n" "\n" "Shall I adjust those settings in order to enable Spiral Vase?" msgstr "" "The Spiral Vase mode requires:\n" "- one perimeter\n" "- no top solid layers\n" "- 0% fill density\n" "- no support material\n" "- no ensure_vertical_shell_thickness\n" "\n" "Shall I adjust those settings in order to enable Spiral Vase?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:540 msgid "Spiral Vase" msgstr "Spiral Vase" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:560 msgid "" "The Wipe Tower currently supports only:\n" "- first layer height 0.2mm\n" "- layer height from 0.15mm to 0.35mm\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" msgstr "" "The Wipe Tower currently supports only:\n" "- first layer height 0.2mm\n" "- layer height from 0.15mm to 0.35mm\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:564 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:585 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:602 msgid "Wipe Tower" msgstr "Wipe Tower" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:581 msgid "" "The Wipe Tower currently supports the non-soluble supports only\n" "if they are printed with the current extruder without triggering a tool " "change.\n" "(both support_material_extruder and support_material_interface_extruder need " "to be set to 0).\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" msgstr "" "The Wipe Tower currently supports the non-soluble supports only\n" "if they are printed with the current extruder without triggering a tool " "change.\n" "(both support_material_extruder and support_material_interface_extruder need " "to be set to 0).\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:599 msgid "" "For the Wipe Tower to work with the soluble supports, the support layers\n" "need to be synchronized with the object layers.\n" "\n" "Shall I synchronize support layers in order to enable the Wipe Tower?" msgstr "" "For the Wipe Tower to work with the soluble supports, the support layers\n" "need to be synchronized with the object layers.\n" "\n" "Shall I synchronize support layers in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:617 msgid "" "Supports work better, if the following feature is enabled:\n" "- Detect bridging perimeters\n" "\n" "Shall I adjust those settings for supports?" msgstr "" "Supports work better, if the following feature is enabled:\n" "- Detect bridging perimeters\n" "\n" "Shall I adjust those settings for supports?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:620 msgid "Support Generator" msgstr "Support Generator" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:662 msgid "The " msgstr "The " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:662 #, no-c-format msgid "" " infill pattern is not supposed to work at 100% density.\n" "\n" "Shall I switch to rectilinear fill pattern?" msgstr "" " infill pattern is not supposed to work at 100% density.\n" "\n" "Shall I switch to rectilinear fill pattern?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:786 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:787 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:368 msgid "Filament" msgstr "Filament" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:794 msgid "Temperature " msgstr "Temperature " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:795 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1234 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:307 msgid "Extruder" msgstr "Extruder" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:800 msgid "Bed" msgstr "Bed" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:805 msgid "Cooling" msgstr "Cooling" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:806 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:922 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1695 msgid "Enable" msgstr "Enable" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:817 msgid "Fan settings" msgstr "Fan settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:818 msgid "Fan speed" msgstr "Fan speed" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:826 msgid "Cooling thresholds" msgstr "Cooling thresholds" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:832 msgid "Filament properties" msgstr "Filament properties" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:836 msgid "Print speed override" msgstr "Print speed override" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:846 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1119 msgid "Custom G-code" msgstr "Custom G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:847 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1120 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1342 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1357 msgid "Start G-code" msgstr "Start G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:853 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1126 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:217 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:227 msgid "End G-code" msgstr "End G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:937 #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:11 msgid "General" msgstr "General" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:938 msgid "Size and coordinates" msgstr "Size and coordinates" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:940 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:34 msgid "Bed shape" msgstr "Bed shape" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:942 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1637 msgid " Set " msgstr " Set " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:962 msgid "Capabilities" msgstr "Capabilities" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:967 msgid "Number of extruders of the printer." msgstr "Number of extruders of the printer." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:989 msgid "USB/Serial connection" msgstr "USB/Serial connection" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:990 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1193 msgid "Serial port" msgstr "Serial port" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:995 msgid "Rescan serial ports" msgstr "Rescan serial ports" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1004 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1072 msgid "Test" msgstr "Test" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1017 msgid "Connection to printer works correctly." msgstr "Connection to printer works correctly." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1017 msgid "Success!" msgstr "Success!" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1020 msgid "Connection failed." msgstr "Connection failed." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1032 msgid "OctoPrint upload" msgstr "OctoPrint upload" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1035 msgid " Browse " msgstr " Browse " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1110 msgid "Firmware" msgstr "Firmware" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1132 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:48 msgid "Before layer change G-code" msgstr "Before layer change G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1138 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:766 msgid "After layer change G-code" msgstr "After layer change G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1144 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1602 msgid "Tool change G-code" msgstr "Tool change G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1150 msgid "Between objects G-code (for sequential printing)" msgstr "Between objects G-code (for sequential printing)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1187 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:400 #, c-format msgid "Extruder %d" msgstr "Extruder %d" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1194 msgid "Layer height limits" msgstr "Layer height limits" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1199 msgid "Position (for multi-extruder printers)" msgstr "Position (for multi-extruder printers)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1202 msgid "Retraction" msgstr "Retraction" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1205 msgid "Only lift Z" msgstr "Only lift Z" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1218 msgid "" "Retraction when tool is disabled (advanced settings for multi-extruder " "setups)" msgstr "" "Retraction when tool is disabled (advanced settings for multi-extruder " "setups)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1222 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:150 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2125 msgid "Preview" msgstr "Preview" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1312 msgid "" "The Wipe option is not available when using the Firmware Retraction mode.\n" "\n" "Shall I disable it in order to enable Firmware Retraction?" msgstr "" "The Wipe option is not available when using the Firmware Retraction mode.\n" "\n" "Shall I disable it in order to enable Firmware Retraction?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1314 msgid "Firmware Retraction" msgstr "Firmware Retraction" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1469 msgid "Default " msgstr "Default " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1469 msgid " preset" msgstr " preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1470 msgid " preset\n" msgstr " preset\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1488 msgid "" "\n" "\n" "is not compatible with printer\n" msgstr "" "\n" "\n" "is not compatible with printer\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1488 msgid "" "\n" "\n" "and it has the following unsaved changes:" msgstr "" "\n" "\n" "and it has the following unsaved changes:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1489 msgid "" "\n" "\n" "has the following unsaved changes:" msgstr "" "\n" "\n" "has the following unsaved changes:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1491 msgid "" "\n" "\n" "Discard changes and continue anyway?" msgstr "" "\n" "\n" "Discard changes and continue anyway?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1492 msgid "Unsaved Changes" msgstr "Unsaved Changes" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1560 msgid "The supplied name is empty. It can't be saved." msgstr "The supplied name is empty. It can't be saved." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1580 msgid "remove" msgstr "remove" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1580 msgid "delete" msgstr "delete" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1581 msgid "Are you sure you want to " msgstr "Are you sure you want to " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1581 msgid " the selected preset?" msgstr " the selected preset?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1582 msgid "Remove" msgstr "Remove" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1582 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:178 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:196 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2021 msgid "Delete" msgstr "Delete" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1583 msgid " Preset" msgstr " Preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1636 msgid "All" msgstr "All" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1667 msgid "Select the printers this profile is compatible with." msgstr "Select the printers this profile is compatible with." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1751 #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:514 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1645 msgid "Save " msgstr "Save " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1751 msgid " as:" msgstr " as:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1785 msgid "" "The supplied name is not valid; the following characters are not allowed:" msgstr "" "The supplied name is not valid; the following characters are not allowed:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1788 msgid "The supplied name is not available." msgstr "The supplied name is not available." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:182 msgid "Print Settings" msgstr "Print Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:202 msgid "Filament Settings" msgstr "Filament Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:228 msgid "Printer Settings" msgstr "Printer Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:248 msgid "Save preset" msgstr "Save preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Field.cpp:42 msgid "default" msgstr "default" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:26 #, c-format msgid "" "If estimated layer time is below ~%ds, fan will run at %d%% and print speed " "will be reduced so that no less than %ds are spent on that layer (however, " "speed will never be reduced below %dmm/s)." msgstr "" "If estimated layer time is below ~%ds, fan will run at %d%% and print speed " "will be reduced so that no less than %ds are spent on that layer (however, " "speed will never be reduced below %dmm/s)." #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:30 #, c-format msgid "" "\n" "If estimated layer time is greater, but still below ~%ds, fan will run at a " "proportionally decreasing speed between %d%% and %d%%." msgstr "" "\n" "If estimated layer time is greater, but still below ~%ds, fan will run at a " "proportionally decreasing speed between %d%% and %d%%." #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:34 msgid "" "\n" "During the other layers, fan " msgstr "" "\n" "During the other layers, fan " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:36 msgid "Fan " msgstr "Fan " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:41 #, c-format msgid "will always run at %d%% " msgstr "will always run at %d%% " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:44 #, c-format msgid "except for the first %d layers" msgstr "except for the first %d layers" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:48 msgid "except for the first layer" msgstr "except for the first layer" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:50 msgid "will be turned off." msgstr "will be turned off." #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:151 msgid "external perimeters" msgstr "external perimeters" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:160 msgid "perimeters" msgstr "perimeters" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:169 msgid "infill" msgstr "infill" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:179 msgid "solid infill" msgstr "solid infill" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:187 msgid "top solid infill" msgstr "top solid infill" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:198 msgid "support" msgstr "support" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:208 msgid "support interface" msgstr "support interface" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:214 msgid "First layer volumetric" msgstr "First layer volumetric" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:214 msgid "Bridging volumetric" msgstr "Bridging volumetric" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:214 msgid "Volumetric" msgstr "Volumetric" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:215 msgid " flow rate is maximized " msgstr " flow rate is maximized " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:218 msgid "by the print profile maximum" msgstr "by the print profile maximum" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:219 msgid "when printing " msgstr "when printing " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:220 msgid " with a volumetric rate " msgstr " with a volumetric rate " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:224 #, c-format msgid "%3.2f mm³/s" msgstr "%3.2f mm³/s" #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:226 #, c-format msgid " at filament speed %3.2f mm/s." msgstr " at filament speed %3.2f mm/s." #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:245 msgid "" "Recommended object thin wall thickness: Not available due to invalid layer " "height." msgstr "" "Recommended object thin wall thickness: Not available due to invalid layer " "height." #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:262 #, c-format msgid "Recommended object thin wall thickness for layer height %.2f and " msgstr "Recommended object thin wall thickness for layer height %.2f and " #: c:\src\Slic3r\xs\src\slic3r\GUI\PresetHints.cpp:269 #, c-format msgid "%d lines: %.2lf mm" msgstr "%d lines: %.2lf mm" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.hpp:17 msgid "Preferences" msgstr "Preferences" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:27 msgid "Remember output directory" msgstr "Remember output directory" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:29 msgid "" "If this is enabled, Slic3r will prompt the last output directory instead of " "the one containing the input files." msgstr "" "If this is enabled, Slic3r will prompt the last output directory instead of " "the one containing the input files." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:35 msgid "Auto-center parts" msgstr "Auto-center parts" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:37 msgid "" "If this is enabled, Slic3r will auto-center objects around the print bed " "center." msgstr "" "If this is enabled, Slic3r will auto-center objects around the print bed " "center." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:43 msgid "Background processing" msgstr "Background processing" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:45 msgid "" "If this is enabled, Slic3r will pre-process objects as soon as they're " "loaded in order to save time when exporting G-code." msgstr "" "If this is enabled, Slic3r will pre-process objects as soon as they're " "loaded in order to save time when exporting G-code." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:51 msgid "Disable USB/serial connection" msgstr "Disable USB/serial connection" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:53 msgid "" "Disable communication with the printer over a serial / USB cable. This " "simplifies the user interface in case the printer is never attached to the " "computer." msgstr "" "Disable communication with the printer over a serial / USB cable. This " "simplifies the user interface in case the printer is never attached to the " "computer." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:59 msgid "Suppress \" - default - \" presets" msgstr "Suppress \" - default - \" presets" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:61 msgid "" "Suppress \" - default - \" presets in the Print / Filament / Printer " "selections once there are any other valid presets available." msgstr "" "Suppress \" - default - \" presets in the Print / Filament / Printer " "selections once there are any other valid presets available." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:67 msgid "Show incompatible print and filament presets" msgstr "Show incompatible print and filament presets" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:69 msgid "" "When checked, the print and filament presets are shown in the preset editor " "even if they are marked as incompatible with the active printer" msgstr "" "When checked, the print and filament presets are shown in the preset editor " "even if they are marked as incompatible with the active printer" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:75 msgid "Use legacy OpenGL 1.1 rendering" msgstr "Use legacy OpenGL 1.1 rendering" #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:77 msgid "" "If you have rendering issues caused by a buggy OpenGL 2.0 driver, you may " "try to check this checkbox. This will disable the layer height editing and " "anti aliasing, so it is likely better to upgrade your graphics driver." msgstr "" "If you have rendering issues caused by a buggy OpenGL 2.0 driver, you may " "try to check this checkbox. This will disable the layer height editing and " "anti aliasing, so it is likely better to upgrade your graphics driver." #: c:\src\Slic3r\xs\src\slic3r\GUI\Preferences.cpp:101 msgid "You need to restart Slic3r to make the changes effective." msgstr "You need to restart Slic3r to make the changes effective." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:26 msgid "Avoid crossing perimeters" msgstr "Avoid crossing perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:27 msgid "" "Optimize travel moves in order to minimize the crossing of perimeters. This " "is mostly useful with Bowden extruders which suffer from oozing. This " "feature slows down both the print and the G-code generation." msgstr "" "Optimize travel moves in order to minimize the crossing of perimeters. This " "is mostly useful with Bowden extruders which suffer from oozing. This " "feature slows down both the print and the G-code generation." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:38 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1572 msgid "Other layers" msgstr "Other layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:39 msgid "" "Bed temperature for layers after the first one. Set this to zero to disable " "bed temperature control commands in the output." msgstr "" "Bed temperature for layers after the first one. Set this to zero to disable " "bed temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:42 msgid "Bed temperature" msgstr "Bed temperature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:49 msgid "" "This custom code is inserted at every layer change, right before the Z move. " "Note that you can use placeholder variables for all Slic3r settings as well " "as [layer_num] and [layer_z]." msgstr "" "This custom code is inserted at every layer change, right before the Z move. " "Note that you can use placeholder variables for all Slic3r settings as well " "as [layer_num] and [layer_z]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:59 msgid "Between objects G-code" msgstr "Between objects G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:60 msgid "" "This code is inserted between objects when using sequential printing. By " "default extruder and bed temperature are reset using non-wait command; " "however if M104, M109, M140 or M190 are detected in this custom code, Slic3r " "will not add temperature commands. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want." msgstr "" "This code is inserted between objects when using sequential printing. By " "default extruder and bed temperature are reset using non-wait command; " "however if M104, M109, M140 or M190 are detected in this custom code, Slic3r " "will not add temperature commands. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:68 #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:370 msgid "Bottom" msgstr "Bottom" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:69 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:239 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:290 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:298 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:604 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:762 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:778 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:941 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:989 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1152 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1583 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1639 msgid "Layers and Perimeters" msgstr "Layers and Perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:70 msgid "Number of solid layers to generate on bottom surfaces." msgstr "Number of solid layers to generate on bottom surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:72 msgid "Bottom solid layers" msgstr "Bottom solid layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:77 msgid "Bridge" msgstr "Bridge" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:78 msgid "" "This is the acceleration your printer will use for bridges. Set zero to " "disable acceleration control for bridges." msgstr "" "This is the acceleration your printer will use for bridges. Set zero to " "disable acceleration control for bridges." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:80 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:174 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:576 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:684 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:952 msgid "mm/s²" msgstr "mm/s²" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:86 msgid "Bridging angle" msgstr "Bridging angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:88 msgid "" "Bridging angle override. If left to zero, the bridging angle will be " "calculated automatically. Otherwise the provided angle will be used for all " "bridges. Use 180° for zero angle." msgstr "" "Bridging angle override. If left to zero, the bridging angle will be " "calculated automatically. Otherwise the provided angle will be used for all " "bridges. Use 180° for zero angle." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:91 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:492 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1170 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1181 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1401 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1557 msgid "°" msgstr "°" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:97 msgid "Bridges fan speed" msgstr "Bridges fan speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:98 msgid "This fan speed is enforced during all bridges and overhangs." msgstr "This fan speed is enforced during all bridges and overhangs." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:99 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:504 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:789 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:850 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1060 msgid "%" msgstr "%" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:106 msgid "Bridge flow ratio" msgstr "Bridge flow ratio" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:108 msgid "" "This factor affects the amount of plastic for bridging. You can decrease it " "slightly to pull the extrudates and prevent sagging, although default " "settings are usually good and you should experiment with cooling (use a fan) " "before tweaking this." msgstr "" "This factor affects the amount of plastic for bridging. You can decrease it " "slightly to pull the extrudates and prevent sagging, although default " "settings are usually good and you should experiment with cooling (use a fan) " "before tweaking this." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:117 msgid "Bridges" msgstr "Bridges" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:119 msgid "Speed for printing bridges." msgstr "Speed for printing bridges." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:120 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:638 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:749 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:811 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:868 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:981 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1137 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1146 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1536 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1649 msgid "mm/s" msgstr "mm/s" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:127 msgid "Brim width" msgstr "Brim width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:128 msgid "" "Horizontal width of the brim that will be printed around each object on the " "first layer." msgstr "" "Horizontal width of the brim that will be printed around each object on the " "first layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:135 msgid "Clip multi-part objects" msgstr "Clip multi-part objects" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:136 msgid "" "When printing multi-material objects, this settings will make slic3r to clip " "the overlapping object parts one by the other (2nd part will be clipped by " "the 1st, 3rd part will be clipped by the 1st and 2nd etc)." msgstr "" "When printing multi-material objects, this settings will make slic3r to clip " "the overlapping object parts one by the other (2nd part will be clipped by " "the 1st, 3rd part will be clipped by the 1st and 2nd etc)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:147 msgid "Compatible printers condition" msgstr "Compatible printers condition" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:148 msgid "" "A boolean expression using the configuration values of an active printer " "profile. If this expression evaluates to true, this profile is considered " "compatible with the active printer profile." msgstr "" "A boolean expression using the configuration values of an active printer " "profile. If this expression evaluates to true, this profile is considered " "compatible with the active printer profile." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:154 msgid "Complete individual objects" msgstr "Complete individual objects" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:155 msgid "" "When printing multiple objects or copies, this feature will complete each " "object before moving onto next one (and starting it from its bottom layer). " "This feature is useful to avoid the risk of ruined prints. Slic3r should " "warn and prevent you from extruder collisions, but beware." msgstr "" "When printing multiple objects or copies, this feature will complete each " "object before moving onto next one (and starting it from its bottom layer). " "This feature is useful to avoid the risk of ruined prints. Slic3r should " "warn and prevent you from extruder collisions, but beware." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:163 msgid "Enable auto cooling" msgstr "Enable auto cooling" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:164 msgid "" "This flag enables the automatic cooling logic that adjusts print speed and " "fan speed according to layer printing time." msgstr "" "This flag enables the automatic cooling logic that adjusts print speed and " "fan speed according to layer printing time." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:171 msgid "" "This is the acceleration your printer will be reset to after the role-" "specific acceleration values are used (perimeter/infill). Set zero to " "prevent resetting acceleration at all." msgstr "" "This is the acceleration your printer will be reset to after the role-" "specific acceleration values are used (perimeter/infill). Set zero to " "prevent resetting acceleration at all." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:180 msgid "Disable fan for the first" msgstr "Disable fan for the first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:181 msgid "" "You can set this to a positive value to disable fan at all during the first " "layers, so that it does not make adhesion worse." msgstr "" "You can set this to a positive value to disable fan at all during the first " "layers, so that it does not make adhesion worse." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:183 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:694 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1033 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1224 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1285 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1437 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1482 msgid "layers" msgstr "layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:190 msgid "Don't support bridges" msgstr "Don't support bridges" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:192 msgid "" "Experimental option for preventing support material from being generated " "under bridged areas." msgstr "" "Experimental option for preventing support material from being generated " "under bridged areas." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:198 msgid "Distance between copies" msgstr "Distance between copies" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:199 msgid "Distance used for the auto-arrange feature of the plater." msgstr "Distance used for the auto-arrange feature of the plater." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:207 msgid "Elephant foot compensation" msgstr "Elephant foot compensation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:209 msgid "" "The first layer will be shrunk in the XY plane by the configured value to " "compensate for the 1st layer squish aka an Elephant Foot effect." msgstr "" "The first layer will be shrunk in the XY plane by the configured value to " "compensate for the 1st layer squish aka an Elephant Foot effect." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:218 msgid "" "This end procedure is inserted at the end of the output file. Note that you " "can use placeholder variables for all Slic3r settings." msgstr "" "This end procedure is inserted at the end of the output file. Note that you " "can use placeholder variables for all Slic3r settings." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:228 msgid "" "This end procedure is inserted at the end of the output file, before the " "printer end gcode. Note that you can use placeholder variables for all " "Slic3r settings. If you have multiple extruders, the gcode is processed in " "extruder order." msgstr "" "This end procedure is inserted at the end of the output file, before the " "printer end gcode. Note that you can use placeholder variables for all " "Slic3r settings. If you have multiple extruders, the gcode is processed in " "extruder order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:238 msgid "Ensure vertical shell thickness" msgstr "Ensure vertical shell thickness" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:240 msgid "" "Add solid infill near sloping surfaces to guarantee the vertical shell " "thickness (top+bottom solid layers)." msgstr "" "Add solid infill near sloping surfaces to guarantee the vertical shell " "thickness (top+bottom solid layers)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:246 msgid "Top/bottom fill pattern" msgstr "Top/bottom fill pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:248 msgid "" "Fill pattern for top/bottom infill. This only affects the external visible " "layer, and not its adjacent solid shells." msgstr "" "Fill pattern for top/bottom infill. This only affects the external visible " "layer, and not its adjacent solid shells." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:267 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:277 msgid "External perimeters" msgstr "External perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:268 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:377 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:592 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:710 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:967 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1292 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1454 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1614 msgid "Extrusion Width" msgstr "Extrusion Width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:269 msgid "" "Set this to a non-zero value to set a manual extrusion width for external " "perimeters. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 200%), it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for external " "perimeters. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 200%), it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:272 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:597 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:715 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:972 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1296 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1458 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1619 msgid "mm or % (leave 0 for default)" msgstr "mm or % (leave 0 for default)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:279 msgid "" "This separate setting will affect the speed of external perimeters (the " "visible ones). If expressed as percentage (for example: 80%) it will be " "calculated on the perimeters speed setting above. Set to zero for auto." msgstr "" "This separate setting will affect the speed of external perimeters (the " "visible ones). If expressed as percentage (for example: 80%) it will be " "calculated on the perimeters speed setting above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:282 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:619 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1255 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1306 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1501 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1631 msgid "mm/s or %" msgstr "mm/s or %" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:289 msgid "External perimeters first" msgstr "External perimeters first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:291 msgid "" "Print contour perimeters from the outermost one to the innermost one instead " "of the default inverse order." msgstr "" "Print contour perimeters from the outermost one to the innermost one instead " "of the default inverse order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:297 msgid "Extra perimeters if needed" msgstr "Extra perimeters if needed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:299 #, no-c-format msgid "" "Add more perimeters when needed for avoiding gaps in sloping walls. Slic3r " "keeps adding perimeters, until more than 70% of the loop immediately above " "is supported." msgstr "" "Add more perimeters when needed for avoiding gaps in sloping walls. Slic3r " "keeps adding perimeters, until more than 70% of the loop immediately above " "is supported." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:309 msgid "" "The extruder to use (unless more specific extruder settings are specified). " "This value overrides perimeter and infill extruders, but not the support " "extruders." msgstr "" "The extruder to use (unless more specific extruder settings are specified). " "This value overrides perimeter and infill extruders, but not the support " "extruders." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:320 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:69 msgid "Height" msgstr "Height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:321 msgid "" "Set this to the vertical distance between your nozzle tip and (usually) the " "X carriage rods. In other words, this is the height of the clearance " "cylinder around your extruder, and it represents the maximum depth the " "extruder can peek before colliding with other printed objects." msgstr "" "Set this to the vertical distance between your nozzle tip and (usually) the " "X carriage rods. In other words, this is the height of the clearance " "cylinder around your extruder, and it represents the maximum depth the " "extruder can peek before colliding with other printed objects." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:331 msgid "Radius" msgstr "Radius" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:332 msgid "" "Set this to the clearance radius around your extruder. If the extruder is " "not centered, choose the largest value for safety. This setting is used to " "check for collisions and to display the graphical preview in the plater." msgstr "" "Set this to the clearance radius around your extruder. If the extruder is " "not centered, choose the largest value for safety. This setting is used to " "check for collisions and to display the graphical preview in the plater." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:342 msgid "Extruder Color" msgstr "Extruder Color" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:343 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:406 msgid "This is only used in the Slic3r interface as a visual help." msgstr "This is only used in the Slic3r interface as a visual help." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:350 msgid "Extruder offset" msgstr "Extruder offset" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:351 msgid "" "If your firmware doesn't handle the extruder displacement you need the G-" "code to take it into account. This option lets you specify the displacement " "of each extruder with respect to the first one. It expects positive " "coordinates (they will be subtracted from the XY coordinate)." msgstr "" "If your firmware doesn't handle the extruder displacement you need the G-" "code to take it into account. This option lets you specify the displacement " "of each extruder with respect to the first one. It expects positive " "coordinates (they will be subtracted from the XY coordinate)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:360 msgid "Extrusion axis" msgstr "Extrusion axis" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:361 msgid "" "Use this option to set the axis letter associated to your printer's extruder " "(usually E but some printers use A)." msgstr "" "Use this option to set the axis letter associated to your printer's extruder " "(usually E but some printers use A)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:367 msgid "Extrusion multiplier" msgstr "Extrusion multiplier" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:368 msgid "" "This factor changes the amount of flow proportionally. You may need to tweak " "this setting to get nice surface finish and correct single wall widths. " "Usual values are between 0.9 and 1.1. If you think you need to change this " "more, check filament diameter and your firmware E steps." msgstr "" "This factor changes the amount of flow proportionally. You may need to tweak " "this setting to get nice surface finish and correct single wall widths. " "Usual values are between 0.9 and 1.1. If you think you need to change this " "more, check filament diameter and your firmware E steps." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:376 msgid "Default extrusion width" msgstr "Default extrusion width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:378 msgid "" "Set this to a non-zero value to allow a manual extrusion width. If left to " "zero, Slic3r derives extrusion widths from the nozzle diameter (see the " "tooltips for perimeter extrusion width, infill extrusion width etc). If " "expressed as percentage (for example: 230%), it will be computed over layer " "height." msgstr "" "Set this to a non-zero value to allow a manual extrusion width. If left to " "zero, Slic3r derives extrusion widths from the nozzle diameter (see the " "tooltips for perimeter extrusion width, infill extrusion width etc). If " "expressed as percentage (for example: 230%), it will be computed over layer " "height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:382 msgid "mm or % (leave 0 for auto)" msgstr "mm or % (leave 0 for auto)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:387 msgid "Keep fan always on" msgstr "Keep fan always on" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:388 msgid "" "If this is enabled, fan will never be disabled and will be kept running at " "least at its minimum speed. Useful for PLA, harmful for ABS." msgstr "" "If this is enabled, fan will never be disabled and will be kept running at " "least at its minimum speed. Useful for PLA, harmful for ABS." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:394 msgid "Enable fan if layer print time is below" msgstr "Enable fan if layer print time is below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:395 msgid "" "If layer print time is estimated below this number of seconds, fan will be " "enabled and its speed will be calculated by interpolating the minimum and " "maximum speeds." msgstr "" "If layer print time is estimated below this number of seconds, fan will be " "enabled and its speed will be calculated by interpolating the minimum and " "maximum speeds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:397 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1242 msgid "approximate seconds" msgstr "approximate seconds" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:405 msgid "Color" msgstr "Color" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:412 msgid "Filament notes" msgstr "Filament notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:413 msgid "You can put your notes regarding the filament here." msgstr "You can put your notes regarding the filament here." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:421 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:817 msgid "Max volumetric speed" msgstr "Max volumetric speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:422 msgid "" "Maximum volumetric speed allowed for this filament. Limits the maximum " "volumetric speed of a print to the minimum of print and filament volumetric " "speed. Set to zero for no limit." msgstr "" "Maximum volumetric speed allowed for this filament. Limits the maximum " "volumetric speed of a print to the minimum of print and filament volumetric " "speed. Set to zero for no limit." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:425 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:820 msgid "mm³/s" msgstr "mm³/s" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:432 msgid "" "Enter your filament diameter here. Good precision is required, so use a " "caliper and do multiple measurements along the filament, then compute the " "average." msgstr "" "Enter your filament diameter here. Good precision is required, so use a " "caliper and do multiple measurements along the filament, then compute the " "average." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:440 msgid "Density" msgstr "Density" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:441 msgid "" "Enter your filament density here. This is only for statistical information. " "A decent way is to weigh a known length of filament and compute the ratio of " "the length to volume. Better is to calculate the volume directly through " "displacement." msgstr "" "Enter your filament density here. This is only for statistical information. " "A decent way is to weigh a known length of filament and compute the ratio of " "the length to volume. Better is to calculate the volume directly through " "displacement." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:444 msgid "g/cm³" msgstr "g/cm³" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:450 msgid "Filament type" msgstr "Filament type" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:451 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1002 msgid "" "If you want to process the output G-code through custom scripts, just list " "their absolute paths here. Separate multiple scripts with a semicolon. " "Scripts will be passed the absolute path to the G-code file as the first " "argument, and they can access the Slic3r config settings by reading " "environment variables." msgstr "" "If you want to process the output G-code through custom scripts, just list " "their absolute paths here. Separate multiple scripts with a semicolon. " "Scripts will be passed the absolute path to the G-code file as the first " "argument, and they can access the Slic3r config settings by reading " "environment variables." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:470 msgid "Soluble material" msgstr "Soluble material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:471 msgid "Soluble material is most likely used for a soluble support." msgstr "Soluble material is most likely used for a soluble support." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:476 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:450 msgid "Cost" msgstr "Cost" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:477 msgid "" "Enter your filament cost per kg here. This is only for statistical " "information." msgstr "" "Enter your filament cost per kg here. This is only for statistical " "information." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:478 msgid "money/kg" msgstr "money/kg" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:487 msgid "Fill angle" msgstr "Fill angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:489 msgid "" "Default base angle for infill orientation. Cross-hatching will be applied to " "this. Bridges will be infilled using the best direction Slic3r can detect, " "so this setting does not affect them." msgstr "" "Default base angle for infill orientation. Cross-hatching will be applied to " "this. Bridges will be infilled using the best direction Slic3r can detect, " "so this setting does not affect them." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:501 msgid "Fill density" msgstr "Fill density" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:503 #, no-c-format msgid "Density of internal infill, expressed in the range 0% - 100%." msgstr "Density of internal infill, expressed in the range 0% - 100%." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:539 msgid "Fill pattern" msgstr "Fill pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:541 msgid "Fill pattern for general low-density infill." msgstr "Fill pattern for general low-density infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:573 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:582 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:591 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:625 msgid "First layer" msgstr "First layer" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:574 msgid "" "This is the acceleration your printer will use for first layer. Set zero to " "disable acceleration control for first layer." msgstr "" "This is the acceleration your printer will use for first layer. Set zero to " "disable acceleration control for first layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:583 msgid "" "Heated build plate temperature for the first layer. Set this to zero to " "disable bed temperature control commands in the output." msgstr "" "Heated build plate temperature for the first layer. Set this to zero to " "disable bed temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:593 msgid "" "Set this to a non-zero value to set a manual extrusion width for first " "layer. You can use this to force fatter extrudates for better adhesion. If " "expressed as percentage (for example 120%) it will be computed over first " "layer height. If set to zero, it will use the default extrusion width." msgstr "" "Set this to a non-zero value to set a manual extrusion width for first " "layer. You can use this to force fatter extrudates for better adhesion. If " "expressed as percentage (for example 120%) it will be computed over first " "layer height. If set to zero, it will use the default extrusion width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:603 msgid "First layer height" msgstr "First layer height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:605 msgid "" "When printing with very low layer heights, you might still want to print a " "thicker bottom layer to improve adhesion and tolerance for non perfect build " "plates. This can be expressed as an absolute value or as a percentage (for " "example: 150%) over the default layer height." msgstr "" "When printing with very low layer heights, you might still want to print a " "thicker bottom layer to improve adhesion and tolerance for non perfect build " "plates. This can be expressed as an absolute value or as a percentage (for " "example: 150%) over the default layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:609 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:740 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1390 msgid "mm or %" msgstr "mm or %" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:615 msgid "First layer speed" msgstr "First layer speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:616 msgid "" "If expressed as absolute value in mm/s, this speed will be applied to all " "the print moves of the first layer, regardless of their type. If expressed " "as a percentage (for example: 40%) it will scale the default speeds." msgstr "" "If expressed as absolute value in mm/s, this speed will be applied to all " "the print moves of the first layer, regardless of their type. If expressed " "as a percentage (for example: 40%) it will scale the default speeds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:626 msgid "" "Extruder temperature for first layer. If you want to control temperature " "manually during print, set this to zero to disable temperature control " "commands in the output file." msgstr "" "Extruder temperature for first layer. If you want to control temperature " "manually during print, set this to zero to disable temperature control " "commands in the output file." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:634 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:145 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:87 msgid "Gap fill" msgstr "Gap fill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:636 msgid "" "Speed for filling small gaps using short zigzag moves. Keep this reasonably " "low to avoid too much shaking and resonance issues. Set zero to disable gaps " "filling." msgstr "" "Speed for filling small gaps using short zigzag moves. Keep this reasonably " "low to avoid too much shaking and resonance issues. Set zero to disable gaps " "filling." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:644 msgid "Verbose G-code" msgstr "Verbose G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:645 msgid "" "Enable this to get a commented G-code file, with each line explained by a " "descriptive text. If you print from SD card, the additional weight of the " "file could make your firmware slow down." msgstr "" "Enable this to get a commented G-code file, with each line explained by a " "descriptive text. If you print from SD card, the additional weight of the " "file could make your firmware slow down." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:652 msgid "G-code flavor" msgstr "G-code flavor" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:653 msgid "" "Some G/M-code commands, including temperature control and others, are not " "universal. Set this option to your printer's firmware to get a compatible " "output. The \"No extrusion\" flavor prevents Slic3r from exporting any " "extrusion value at all." msgstr "" "Some G/M-code commands, including temperature control and others, are not " "universal. Set this option to your printer's firmware to get a compatible " "output. The \"No extrusion\" flavor prevents Slic3r from exporting any " "extrusion value at all." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:682 msgid "" "This is the acceleration your printer will use for infill. Set zero to " "disable acceleration control for infill." msgstr "" "This is the acceleration your printer will use for infill. Set zero to " "disable acceleration control for infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:690 msgid "Combine infill every" msgstr "Combine infill every" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:692 msgid "" "This feature allows to combine infill and speed up your print by extruding " "thicker infill layers while preserving thin perimeters, thus accuracy." msgstr "" "This feature allows to combine infill and speed up your print by extruding " "thicker infill layers while preserving thin perimeters, thus accuracy." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:696 msgid "Combine infill every n layers" msgstr "Combine infill every n layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:701 msgid "Infill extruder" msgstr "Infill extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:703 msgid "The extruder to use when printing infill." msgstr "The extruder to use when printing infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:711 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. You may want to use fatter extrudates to speed " "up the infill and make your parts stronger. If expressed as percentage (for " "example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. You may want to use fatter extrudates to speed " "up the infill and make your parts stronger. If expressed as percentage (for " "example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:720 msgid "Infill before perimeters" msgstr "Infill before perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:721 msgid "" "This option will switch the print order of perimeters and infill, making the " "latter first." msgstr "" "This option will switch the print order of perimeters and infill, making the " "latter first." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:726 msgid "Only infill where needed" msgstr "Only infill where needed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:728 msgid "" "This option will limit infill to the areas actually needed for supporting " "ceilings (it will act as internal support material). If enabled, slows down " "the G-code generation due to the multiple checks involved." msgstr "" "This option will limit infill to the areas actually needed for supporting " "ceilings (it will act as internal support material). If enabled, slows down " "the G-code generation due to the multiple checks involved." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:735 msgid "Infill/perimeters overlap" msgstr "Infill/perimeters overlap" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:737 msgid "" "This setting applies an additional overlap between infill and perimeters for " "better bonding. Theoretically this shouldn't be needed, but backlash might " "cause gaps. If expressed as percentage (example: 15%) it is calculated over " "perimeter extrusion width." msgstr "" "This setting applies an additional overlap between infill and perimeters for " "better bonding. Theoretically this shouldn't be needed, but backlash might " "cause gaps. If expressed as percentage (example: 15%) it is calculated over " "perimeter extrusion width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:748 msgid "Speed for printing the internal fill. Set to zero for auto." msgstr "Speed for printing the internal fill. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:757 msgid "Interface shells" msgstr "Interface shells" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:758 msgid "" "Force the generation of solid shells between adjacent materials/volumes. " "Useful for multi-extruder prints with translucent materials or manual " "soluble support material." msgstr "" "Force the generation of solid shells between adjacent materials/volumes. " "Useful for multi-extruder prints with translucent materials or manual " "soluble support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:767 msgid "" "This custom code is inserted at every layer change, right after the Z move " "and before the extruder moves to the first layer point. Note that you can " "use placeholder variables for all Slic3r settings as well as [layer_num] and " "[layer_z]." msgstr "" "This custom code is inserted at every layer change, right after the Z move " "and before the extruder moves to the first layer point. Note that you can " "use placeholder variables for all Slic3r settings as well as [layer_num] and " "[layer_z]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:779 msgid "" "This setting controls the height (and thus the total number) of the slices/" "layers. Thinner layers give better accuracy but take more time to print." msgstr "" "This setting controls the height (and thus the total number) of the slices/" "layers. Thinner layers give better accuracy but take more time to print." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:787 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:796 msgid "Max" msgstr "Max" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:788 msgid "This setting represents the maximum speed of your fan." msgstr "This setting represents the maximum speed of your fan." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:797 #, no-c-format msgid "" "This is the highest printable layer height for this extruder, used to cap " "the variable layer height and support layer height. Maximum recommended " "layer height is 75% of the extrusion width to achieve reasonable inter-layer " "adhesion. If set to 0, layer height is limited to 75% of the nozzle diameter." msgstr "" "This is the highest printable layer height for this extruder, used to cap " "the variable layer height and support layer height. Maximum recommended " "layer height is 75% of the extrusion width to achieve reasonable inter-layer " "adhesion. If set to 0, layer height is limited to 75% of the nozzle diameter." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:807 msgid "Max print speed" msgstr "Max print speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:808 msgid "" "When setting other speed settings to 0 Slic3r will autocalculate the optimal " "speed in order to keep constant extruder pressure. This experimental setting " "is used to set the highest print speed you want to allow." msgstr "" "When setting other speed settings to 0 Slic3r will autocalculate the optimal " "speed in order to keep constant extruder pressure. This experimental setting " "is used to set the highest print speed you want to allow." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:818 msgid "" "This experimental setting is used to set the maximum volumetric speed your " "extruder supports." msgstr "" "This experimental setting is used to set the maximum volumetric speed your " "extruder supports." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:826 msgid "Max volumetric slope positive" msgstr "Max volumetric slope positive" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:827 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:838 msgid "" "This experimental setting is used to limit the speed of change in extrusion " "rate. A value of 1.8 mm³/s² ensures, that a change from the extrusion rate " "of 1.8 mm³/s (0.45mm extrusion width, 0.2mm extrusion height, feedrate 20 mm/" "s) to 5.4 mm³/s (feedrate 60 mm/s) will take at least 2 seconds." msgstr "" "This experimental setting is used to limit the speed of change in extrusion " "rate. A value of 1.8 mm³/s² ensures, that a change from the extrusion rate " "of 1.8 mm³/s (0.45mm extrusion width, 0.2mm extrusion height, feedrate 20 mm/" "s) to 5.4 mm³/s (feedrate 60 mm/s) will take at least 2 seconds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:831 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:842 msgid "mm³/s²" msgstr "mm³/s²" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:837 msgid "Max volumetric slope negative" msgstr "Max volumetric slope negative" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:848 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:857 msgid "Min" msgstr "Min" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:849 msgid "This setting represents the minimum PWM your fan needs to work." msgstr "This setting represents the minimum PWM your fan needs to work." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:858 msgid "" "This is the lowest printable layer height for this extruder and limits the " "resolution for variable layer height. Typical values are between 0.05 mm and " "0.1 mm." msgstr "" "This is the lowest printable layer height for this extruder and limits the " "resolution for variable layer height. Typical values are between 0.05 mm and " "0.1 mm." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:866 msgid "Min print speed" msgstr "Min print speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:867 msgid "Slic3r will not scale speed down below this speed." msgstr "Slic3r will not scale speed down below this speed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:874 msgid "Minimum extrusion length" msgstr "Minimum extrusion length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:875 msgid "" "Generate no less than the number of skirt loops required to consume the " "specified amount of filament on the bottom layer. For multi-extruder " "machines, this minimum applies to each extruder." msgstr "" "Generate no less than the number of skirt loops required to consume the " "specified amount of filament on the bottom layer. For multi-extruder " "machines, this minimum applies to each extruder." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:884 msgid "Configuration notes" msgstr "Configuration notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:885 msgid "" "You can put here your personal notes. This text will be added to the G-code " "header comments." msgstr "" "You can put here your personal notes. This text will be added to the G-code " "header comments." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:894 msgid "Nozzle diameter" msgstr "Nozzle diameter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:895 msgid "" "This is the diameter of your extruder nozzle (for example: 0.5, 0.35 etc.)" msgstr "" "This is the diameter of your extruder nozzle (for example: 0.5, 0.35 etc.)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:901 msgid "API Key" msgstr "API Key" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:902 msgid "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "API Key required for authentication." msgstr "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "API Key required for authentication." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:908 msgid "Host or IP" msgstr "Host or IP" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:909 msgid "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "hostname or IP address of the OctoPrint instance." msgstr "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "hostname or IP address of the OctoPrint instance." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:915 msgid "Only retract when crossing perimeters" msgstr "Only retract when crossing perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:916 msgid "" "Disables retraction when the travel path does not exceed the upper layer's " "perimeters (and thus any ooze will be probably invisible)." msgstr "" "Disables retraction when the travel path does not exceed the upper layer's " "perimeters (and thus any ooze will be probably invisible)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:923 msgid "" "This option will drop the temperature of the inactive extruders to prevent " "oozing. It will enable a tall skirt automatically and move extruders outside " "such skirt when changing temperatures." msgstr "" "This option will drop the temperature of the inactive extruders to prevent " "oozing. It will enable a tall skirt automatically and move extruders outside " "such skirt when changing temperatures." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:930 msgid "Output filename format" msgstr "Output filename format" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:931 msgid "" "You can use all configuration options as variables inside this template. For " "example: [layer_height], [fill_density] etc. You can also use [timestamp], " "[year], [month], [day], [hour], [minute], [second], [version], " "[input_filename], [input_filename_base]." msgstr "" "You can use all configuration options as variables inside this template. For " "example: [layer_height], [fill_density] etc. You can also use [timestamp], " "[year], [month], [day], [hour], [minute], [second], [version], " "[input_filename], [input_filename_base]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:940 msgid "Detect bridging perimeters" msgstr "Detect bridging perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:942 msgid "" "Experimental option to adjust flow for overhangs (bridge flow will be used), " "to apply bridge speed to them and enable fan." msgstr "" "Experimental option to adjust flow for overhangs (bridge flow will be used), " "to apply bridge speed to them and enable fan." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:948 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:966 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:978 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:988 msgid "Perimeters" msgstr "Perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:949 msgid "" "This is the acceleration your printer will use for perimeters. A high value " "like 9000 usually gives good results if your hardware is up to the job. Set " "zero to disable acceleration control for perimeters." msgstr "" "This is the acceleration your printer will use for perimeters. A high value " "like 9000 usually gives good results if your hardware is up to the job. Set " "zero to disable acceleration control for perimeters." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:957 msgid "Perimeter extruder" msgstr "Perimeter extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:959 msgid "" "The extruder to use when printing perimeters and brim. First extruder is 1." msgstr "" "The extruder to use when printing perimeters and brim. First extruder is 1." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:968 msgid "" "Set this to a non-zero value to set a manual extrusion width for perimeters. " "You may want to use thinner extrudates to get more accurate surfaces. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. If expressed as percentage (for example 200%) " "it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for perimeters. " "You may want to use thinner extrudates to get more accurate surfaces. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. If expressed as percentage (for example 200%) " "it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:980 msgid "" "Speed for perimeters (contours, aka vertical shells). Set to zero for auto." msgstr "" "Speed for perimeters (contours, aka vertical shells). Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:990 msgid "" "This option sets the number of perimeters to generate for each layer. Note " "that Slic3r may increase this number automatically when it detects sloping " "surfaces which benefit from a higher number of perimeters if the Extra " "Perimeters option is enabled." msgstr "" "This option sets the number of perimeters to generate for each layer. Note " "that Slic3r may increase this number automatically when it detects sloping " "surfaces which benefit from a higher number of perimeters if the Extra " "Perimeters option is enabled." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:994 msgid "(minimum)" msgstr "(minimum)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1014 msgid "Printer notes" msgstr "Printer notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1015 msgid "You can put your notes regarding the printer here." msgstr "You can put your notes regarding the printer here." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1029 msgid "Raft layers" msgstr "Raft layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1031 msgid "" "The object will be raised by this number of layers, and support material " "will be generated under it." msgstr "" "The object will be raised by this number of layers, and support material " "will be generated under it." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1039 msgid "Resolution" msgstr "Resolution" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1040 msgid "" "Minimum detail resolution, used to simplify the input file for speeding up " "the slicing job and reducing memory usage. High-resolution models often " "carry more detail than printers can render. Set to zero to disable any " "simplification and use full resolution from input." msgstr "" "Minimum detail resolution, used to simplify the input file for speeding up " "the slicing job and reducing memory usage. High-resolution models often " "carry more detail than printers can render. Set to zero to disable any " "simplification and use full resolution from input." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1050 msgid "Minimum travel after retraction" msgstr "Minimum travel after retraction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1051 msgid "" "Retraction is not triggered when travel moves are shorter than this length." msgstr "" "Retraction is not triggered when travel moves are shorter than this length." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1057 msgid "Retract amount before wipe" msgstr "Retract amount before wipe" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1058 msgid "" "With bowden extruders, it may be wise to do some amount of quick retract " "before doing the wipe movement." msgstr "" "With bowden extruders, it may be wise to do some amount of quick retract " "before doing the wipe movement." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1065 msgid "Retract on layer change" msgstr "Retract on layer change" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1066 msgid "This flag enforces a retraction whenever a Z move is done." msgstr "This flag enforces a retraction whenever a Z move is done." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1071 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1080 msgid "Length" msgstr "Length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1072 msgid "Retraction Length" msgstr "Retraction Length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1073 msgid "" "When retraction is triggered, filament is pulled back by the specified " "amount (the length is measured on raw filament, before it enters the " "extruder)." msgstr "" "When retraction is triggered, filament is pulled back by the specified " "amount (the length is measured on raw filament, before it enters the " "extruder)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1075 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1085 msgid "mm (zero to disable)" msgstr "mm (zero to disable)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1081 msgid "Retraction Length (Toolchange)" msgstr "Retraction Length (Toolchange)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1082 msgid "" "When retraction is triggered before changing tool, filament is pulled back " "by the specified amount (the length is measured on raw filament, before it " "enters the extruder)." msgstr "" "When retraction is triggered before changing tool, filament is pulled back " "by the specified amount (the length is measured on raw filament, before it " "enters the extruder)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1090 msgid "Lift Z" msgstr "Lift Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1091 msgid "" "If you set this to a positive value, Z is quickly raised every time a " "retraction is triggered. When using multiple extruders, only the setting for " "the first extruder will be considered." msgstr "" "If you set this to a positive value, Z is quickly raised every time a " "retraction is triggered. When using multiple extruders, only the setting for " "the first extruder will be considered." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1099 msgid "Above Z" msgstr "Above Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1100 msgid "Only lift Z above" msgstr "Only lift Z above" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1101 msgid "" "If you set this to a positive value, Z lift will only take place above the " "specified absolute Z. You can tune this setting for skipping lift on the " "first layers." msgstr "" "If you set this to a positive value, Z lift will only take place above the " "specified absolute Z. You can tune this setting for skipping lift on the " "first layers." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1108 msgid "Below Z" msgstr "Below Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1109 msgid "Only lift Z below" msgstr "Only lift Z below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1110 msgid "" "If you set this to a positive value, Z lift will only take place below the " "specified absolute Z. You can tune this setting for limiting lift to the " "first layers." msgstr "" "If you set this to a positive value, Z lift will only take place below the " "specified absolute Z. You can tune this setting for limiting lift to the " "first layers." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1118 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1126 msgid "Extra length on restart" msgstr "Extra length on restart" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1119 msgid "" "When the retraction is compensated after the travel move, the extruder will " "push this additional amount of filament. This setting is rarely needed." msgstr "" "When the retraction is compensated after the travel move, the extruder will " "push this additional amount of filament. This setting is rarely needed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1127 msgid "" "When the retraction is compensated after changing tool, the extruder will " "push this additional amount of filament." msgstr "" "When the retraction is compensated after changing tool, the extruder will " "push this additional amount of filament." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1134 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1135 msgid "Retraction Speed" msgstr "Retraction Speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1136 msgid "The speed for retractions (it only applies to the extruder motor)." msgstr "The speed for retractions (it only applies to the extruder motor)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1142 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1143 msgid "Deretraction Speed" msgstr "Deretraction Speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1144 msgid "" "The speed for loading of a filament into extruder after retraction (it only " "applies to the extruder motor). If left to zero, the retraction speed is " "used." msgstr "" "The speed for loading of a filament into extruder after retraction (it only " "applies to the extruder motor). If left to zero, the retraction speed is " "used." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1151 msgid "Seam position" msgstr "Seam position" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1153 msgid "Position of perimeters starting points." msgstr "Position of perimeters starting points." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1169 msgid "Direction" msgstr "Direction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1171 msgid "Preferred direction of the seam" msgstr "Preferred direction of the seam" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1172 msgid "Seam preferred direction" msgstr "Seam preferred direction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1180 msgid "Jitter" msgstr "Jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1182 msgid "Seam preferred direction jitter" msgstr "Seam preferred direction jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1183 msgid "Preferred direction of the seam - jitter" msgstr "Preferred direction of the seam - jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1194 msgid "USB/serial port for printer connection." msgstr "USB/serial port for printer connection." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1202 msgid "Serial port speed" msgstr "Serial port speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1203 msgid "Speed (baud) of USB/serial port for printer connection." msgstr "Speed (baud) of USB/serial port for printer connection." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1212 msgid "Distance from object" msgstr "Distance from object" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1213 msgid "" "Distance between skirt and object(s). Set this to zero to attach the skirt " "to the object(s) and get a brim for better adhesion." msgstr "" "Distance between skirt and object(s). Set this to zero to attach the skirt " "to the object(s) and get a brim for better adhesion." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1221 msgid "Skirt height" msgstr "Skirt height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1222 msgid "" "Height of skirt expressed in layers. Set this to a tall value to use skirt " "as a shield against drafts." msgstr "" "Height of skirt expressed in layers. Set this to a tall value to use skirt " "as a shield against drafts." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1229 msgid "Loops (minimum)" msgstr "Loops (minimum)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1230 msgid "Skirt Loops" msgstr "Skirt Loops" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1231 msgid "" "Number of loops for the skirt. If the Minimum Extrusion Length option is " "set, the number of loops might be greater than the one configured here. Set " "this to zero to disable skirt completely." msgstr "" "Number of loops for the skirt. If the Minimum Extrusion Length option is " "set, the number of loops might be greater than the one configured here. Set " "this to zero to disable skirt completely." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1239 msgid "Slow down if layer print time is below" msgstr "Slow down if layer print time is below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1240 msgid "" "If layer print time is estimated below this number of seconds, print moves " "speed will be scaled down to extend duration to this value." msgstr "" "If layer print time is estimated below this number of seconds, print moves " "speed will be scaled down to extend duration to this value." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1250 msgid "Small perimeters" msgstr "Small perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1252 msgid "" "This separate setting will affect the speed of perimeters having radius <= " "6.5mm (usually holes). If expressed as percentage (for example: 80%) it will " "be calculated on the perimeters speed setting above. Set to zero for auto." msgstr "" "This separate setting will affect the speed of perimeters having radius <= " "6.5mm (usually holes). If expressed as percentage (for example: 80%) it will " "be calculated on the perimeters speed setting above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1262 msgid "Solid infill threshold area" msgstr "Solid infill threshold area" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1264 msgid "" "Force solid infill for regions having a smaller area than the specified " "threshold." msgstr "" "Force solid infill for regions having a smaller area than the specified " "threshold." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1265 msgid "mm²" msgstr "mm²" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1271 msgid "Solid infill extruder" msgstr "Solid infill extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1273 msgid "The extruder to use when printing solid infill." msgstr "The extruder to use when printing solid infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1279 msgid "Solid infill every" msgstr "Solid infill every" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1281 msgid "" "This feature allows to force a solid layer every given number of layers. " "Zero to disable. You can set this to any value (for example 9999); Slic3r " "will automatically choose the maximum possible number of layers to combine " "according to nozzle diameter and layer height." msgstr "" "This feature allows to force a solid layer every given number of layers. " "Zero to disable. You can set this to any value (for example 9999); Slic3r " "will automatically choose the maximum possible number of layers to combine " "according to nozzle diameter and layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1291 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1301 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:142 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:84 msgid "Solid infill" msgstr "Solid infill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1293 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill for " "solid surfaces. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill for " "solid surfaces. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1303 msgid "" "Speed for printing solid regions (top/bottom/internal horizontal shells). " "This can be expressed as a percentage (for example: 80%) over the default " "infill speed above. Set to zero for auto." msgstr "" "Speed for printing solid regions (top/bottom/internal horizontal shells). " "This can be expressed as a percentage (for example: 80%) over the default " "infill speed above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1315 msgid "Number of solid layers to generate on top and bottom surfaces." msgstr "Number of solid layers to generate on top and bottom surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1322 msgid "Spiral vase" msgstr "Spiral vase" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1323 msgid "" "This feature will raise Z gradually while printing a single-walled object in " "order to remove any visible seam. This option requires a single perimeter, " "no infill, no top solid layers and no support material. You can still set " "any number of bottom solid layers as well as skirt/brim loops. It won't work " "when printing more than an object." msgstr "" "This feature will raise Z gradually while printing a single-walled object in " "order to remove any visible seam. This option requires a single perimeter, " "no infill, no top solid layers and no support material. You can still set " "any number of bottom solid layers as well as skirt/brim loops. It won't work " "when printing more than an object." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1332 msgid "Temperature variation" msgstr "Temperature variation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1333 msgid "" "Temperature difference to be applied when an extruder is not active. Enables " "a full-height \"sacrificial\" skirt on which the nozzles are periodically " "wiped." msgstr "" "Temperature difference to be applied when an extruder is not active. Enables " "a full-height \"sacrificial\" skirt on which the nozzles are periodically " "wiped." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1343 msgid "" "This start procedure is inserted at the beginning, after bed has reached the " "target temperature and extruder just started heating, and before extruder " "has finished heating. If Slic3r detects M104 or M190 in your custom codes, " "such commands will not be prepended automatically so you're free to " "customize the order of heating commands and other custom actions. Note that " "you can use placeholder variables for all Slic3r settings, so you can put a " "\"M109 S[first_layer_temperature]\" command wherever you want." msgstr "" "This start procedure is inserted at the beginning, after bed has reached the " "target temperature and extruder just started heating, and before extruder " "has finished heating. If Slic3r detects M104 or M190 in your custom codes, " "such commands will not be prepended automatically so you're free to " "customize the order of heating commands and other custom actions. Note that " "you can use placeholder variables for all Slic3r settings, so you can put a " "\"M109 S[first_layer_temperature]\" command wherever you want." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1358 msgid "" "This start procedure is inserted at the beginning, after any printer start " "gcode. This is used to override settings for a specific filament. If Slic3r " "detects M104, M109, M140 or M190 in your custom codes, such commands will " "not be prepended automatically so you're free to customize the order of " "heating commands and other custom actions. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want. If you have multiple " "extruders, the gcode is processed in extruder order." msgstr "" "This start procedure is inserted at the beginning, after any printer start " "gcode. This is used to override settings for a specific filament. If Slic3r " "detects M104, M109, M140 or M190 in your custom codes, such commands will " "not be prepended automatically so you're free to customize the order of " "heating commands and other custom actions. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want. If you have multiple " "extruders, the gcode is processed in extruder order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1373 msgid "Single Extruder Multi Material" msgstr "Single Extruder Multi Material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1374 msgid "The printer multiplexes filaments into a single hot end." msgstr "The printer multiplexes filaments into a single hot end." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1379 msgid "Generate support material" msgstr "Generate support material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1381 msgid "Enable support material generation." msgstr "Enable support material generation." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1386 msgid "XY separation between an object and its support" msgstr "XY separation between an object and its support" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1388 msgid "" "XY separation between an object and its support. If expressed as percentage " "(for example 50%), it will be calculated over external perimeter width." msgstr "" "XY separation between an object and its support. If expressed as percentage " "(for example 50%), it will be calculated over external perimeter width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1398 msgid "Pattern angle" msgstr "Pattern angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1400 msgid "" "Use this setting to rotate the support material pattern on the horizontal " "plane." msgstr "" "Use this setting to rotate the support material pattern on the horizontal " "plane." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1408 msgid "Support on build plate only" msgstr "Support on build plate only" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1410 msgid "" "Only create support if it lies on a build plate. Don't create support on a " "print." msgstr "" "Only create support if it lies on a build plate. Don't create support on a " "print." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1416 msgid "Contact Z distance" msgstr "Contact Z distance" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1418 msgid "" "The vertical distance between object and support material interface. Setting " "this to 0 will also prevent Slic3r from using bridge flow and speed for the " "first object layer." msgstr "" "The vertical distance between object and support material interface. Setting " "this to 0 will also prevent Slic3r from using bridge flow and speed for the " "first object layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1431 msgid "Enforce support for the first" msgstr "Enforce support for the first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1433 msgid "" "Generate support material for the specified number of layers counting from " "bottom, regardless of whether normal support material is enabled or not and " "regardless of any angle threshold. This is useful for getting more adhesion " "of objects having a very thin or poor footprint on the build plate." msgstr "" "Generate support material for the specified number of layers counting from " "bottom, regardless of whether normal support material is enabled or not and " "regardless of any angle threshold. This is useful for getting more adhesion " "of objects having a very thin or poor footprint on the build plate." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1439 msgid "Enforce support for the first n layers" msgstr "Enforce support for the first n layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1444 msgid "Support material/raft/skirt extruder" msgstr "Support material/raft/skirt extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1446 msgid "" "The extruder to use when printing support material, raft and skirt (1+, 0 to " "use the current extruder to minimize tool changes)." msgstr "" "The extruder to use when printing support material, raft and skirt (1+, 0 to " "use the current extruder to minimize tool changes)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1455 msgid "" "Set this to a non-zero value to set a manual extrusion width for support " "material. If left zero, default extrusion width will be used if set, " "otherwise nozzle diameter will be used. If expressed as percentage (for " "example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for support " "material. If left zero, default extrusion width will be used if set, " "otherwise nozzle diameter will be used. If expressed as percentage (for " "example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1463 msgid "Interface loops" msgstr "Interface loops" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1465 msgid "" "Cover the top contact layer of the supports with loops. Disabled by default." msgstr "" "Cover the top contact layer of the supports with loops. Disabled by default." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1470 msgid "Support material/raft interface extruder" msgstr "Support material/raft interface extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1472 msgid "" "The extruder to use when printing support material interface (1+, 0 to use " "the current extruder to minimize tool changes). This affects raft too." msgstr "" "The extruder to use when printing support material interface (1+, 0 to use " "the current extruder to minimize tool changes). This affects raft too." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1479 msgid "Interface layers" msgstr "Interface layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1481 msgid "" "Number of interface layers to insert between the object(s) and support " "material." msgstr "" "Number of interface layers to insert between the object(s) and support " "material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1488 msgid "Interface pattern spacing" msgstr "Interface pattern spacing" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1490 msgid "Spacing between interface lines. Set zero to get a solid interface." msgstr "Spacing between interface lines. Set zero to get a solid interface." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1497 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:148 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:90 msgid "Support material interface" msgstr "Support material interface" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1499 msgid "" "Speed for printing support material interface layers. If expressed as " "percentage (for example 50%) it will be calculated over support material " "speed." msgstr "" "Speed for printing support material interface layers. If expressed as " "percentage (for example 50%) it will be calculated over support material " "speed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1508 msgid "Pattern" msgstr "Pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1510 msgid "Pattern used to generate support material." msgstr "Pattern used to generate support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1524 msgid "Pattern spacing" msgstr "Pattern spacing" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1526 msgid "Spacing between support material lines." msgstr "Spacing between support material lines." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1535 msgid "Speed for printing support material." msgstr "Speed for printing support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1542 msgid "Synchronize with object layers" msgstr "Synchronize with object layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1544 msgid "" "Synchronize support layers with the object print layers. This is useful with " "multi-material printers, where the extruder switch is expensive." msgstr "" "Synchronize support layers with the object print layers. This is useful with " "multi-material printers, where the extruder switch is expensive." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1550 msgid "Overhang threshold" msgstr "Overhang threshold" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1552 msgid "" "Support material will not be generated for overhangs whose slope angle (90° " "= vertical) is above the given threshold. In other words, this value " "represent the most horizontal slope (measured from the horizontal plane) " "that you can print without support material. Set to zero for automatic " "detection (recommended)." msgstr "" "Support material will not be generated for overhangs whose slope angle (90° " "= vertical) is above the given threshold. In other words, this value " "represent the most horizontal slope (measured from the horizontal plane) " "that you can print without support material. Set to zero for automatic " "detection (recommended)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1564 msgid "With sheath around the support" msgstr "With sheath around the support" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1566 msgid "" "Add a sheath (a single perimeter line) around the base support. This makes " "the support more reliable, but also more difficult to remove." msgstr "" "Add a sheath (a single perimeter line) around the base support. This makes " "the support more reliable, but also more difficult to remove." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1573 msgid "" "Extruder temperature for layers after the first one. Set this to zero to " "disable temperature control commands in the output." msgstr "" "Extruder temperature for layers after the first one. Set this to zero to " "disable temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1576 msgid "Temperature" msgstr "Temperature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1582 msgid "Detect thin walls" msgstr "Detect thin walls" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1584 msgid "" "Detect single-width walls (parts where two extrusions don't fit and we need " "to collapse them into a single trace)." msgstr "" "Detect single-width walls (parts where two extrusions don't fit and we need " "to collapse them into a single trace)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1590 msgid "Threads" msgstr "Threads" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1591 msgid "" "Threads are used to parallelize long-running tasks. Optimal threads number " "is slightly above the number of available cores/processors." msgstr "" "Threads are used to parallelize long-running tasks. Optimal threads number " "is slightly above the number of available cores/processors." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1603 msgid "" "This custom code is inserted right before every extruder change. Note that " "you can use placeholder variables for all Slic3r settings as well as " "[previous_extruder] and [next_extruder]." msgstr "" "This custom code is inserted right before every extruder change. Note that " "you can use placeholder variables for all Slic3r settings as well as " "[previous_extruder] and [next_extruder]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1613 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1624 #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:143 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:85 msgid "Top solid infill" msgstr "Top solid infill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1615 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill for " "top surfaces. You may want to use thinner extrudates to fill all narrow " "regions and get a smoother finish. If left zero, default extrusion width " "will be used if set, otherwise nozzle diameter will be used. If expressed as " "percentage (for example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill for " "top surfaces. You may want to use thinner extrudates to fill all narrow " "regions and get a smoother finish. If left zero, default extrusion width " "will be used if set, otherwise nozzle diameter will be used. If expressed as " "percentage (for example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1626 msgid "" "Speed for printing top solid layers (it only applies to the uppermost " "external layers and not to their internal solid layers). You may want to " "slow down this to get a nicer surface finish. This can be expressed as a " "percentage (for example: 80%) over the solid infill speed above. Set to zero " "for auto." msgstr "" "Speed for printing top solid layers (it only applies to the uppermost " "external layers and not to their internal solid layers). You may want to " "slow down this to get a nicer surface finish. This can be expressed as a " "percentage (for example: 80%) over the solid infill speed above. Set to zero " "for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1638 #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:369 msgid "Top" msgstr "Top" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1640 msgid "Number of solid layers to generate on top surfaces." msgstr "Number of solid layers to generate on top surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1642 msgid "Top solid layers" msgstr "Top solid layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1647 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:95 msgid "Travel" msgstr "Travel" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1648 msgid "Speed for travel moves (jumps between distant extrusion points)." msgstr "Speed for travel moves (jumps between distant extrusion points)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1656 msgid "Use firmware retraction" msgstr "Use firmware retraction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1657 msgid "" "This experimental setting uses G10 and G11 commands to have the firmware " "handle the retraction. This is only supported in recent Marlin." msgstr "" "This experimental setting uses G10 and G11 commands to have the firmware " "handle the retraction. This is only supported in recent Marlin." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1663 msgid "Use relative E distances" msgstr "Use relative E distances" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1664 msgid "" "If your firmware requires relative E values, check this, otherwise leave it " "unchecked. Most firmwares use absolute values." msgstr "" "If your firmware requires relative E values, check this, otherwise leave it " "unchecked. Most firmwares use absolute values." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1670 msgid "Use volumetric E" msgstr "Use volumetric E" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1671 msgid "" "This experimental setting uses outputs the E values in cubic millimeters " "instead of linear millimeters. If your firmware doesn't already know " "filament diameter(s), you can put commands like 'M200 D[filament_diameter_0] " "T0' in your start G-code in order to turn volumetric mode on and use the " "filament diameter associated to the filament selected in Slic3r. This is " "only supported in recent Marlin." msgstr "" "This experimental setting uses outputs the E values in cubic millimeters " "instead of linear millimeters. If your firmware doesn't already know " "filament diameter(s), you can put commands like 'M200 D[filament_diameter_0] " "T0' in your start G-code in order to turn volumetric mode on and use the " "filament diameter associated to the filament selected in Slic3r. This is " "only supported in recent Marlin." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1681 msgid "Enable variable layer height feature" msgstr "Enable variable layer height feature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1682 msgid "" "Some printers or printer setups may have difficulties printing with a " "variable layer height. Enabled by default." msgstr "" "Some printers or printer setups may have difficulties printing with a " "variable layer height. Enabled by default." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1688 msgid "Wipe while retracting" msgstr "Wipe while retracting" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1689 msgid "" "This flag will move the nozzle while retracting to minimize the possible " "blob on leaky extruders." msgstr "" "This flag will move the nozzle while retracting to minimize the possible " "blob on leaky extruders." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1696 msgid "" "Multi material printers may need to prime or purge extruders on tool " "changes. Extrude the excess material into the wipe tower." msgstr "" "Multi material printers may need to prime or purge extruders on tool " "changes. Extrude the excess material into the wipe tower." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1702 msgid "Position X" msgstr "Position X" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1703 msgid "X coordinate of the left front corner of a wipe tower" msgstr "X coordinate of the left front corner of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1709 msgid "Position Y" msgstr "Position Y" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1710 msgid "Y coordinate of the left front corner of a wipe tower" msgstr "Y coordinate of the left front corner of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1716 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:70 msgid "Width" msgstr "Width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1717 msgid "Width of a wipe tower" msgstr "Width of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1723 msgid "Per color change depth" msgstr "Per color change depth" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1724 msgid "" "Depth of a wipe color per color change. For N colors, there will be maximum " "(N-1) tool switches performed, therefore the total depth of the wipe tower " "will be (N-1) times this value." msgstr "" "Depth of a wipe color per color change. For N colors, there will be maximum " "(N-1) tool switches performed, therefore the total depth of the wipe tower " "will be (N-1) times this value." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1732 msgid "XY Size Compensation" msgstr "XY Size Compensation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1734 msgid "" "The object will be grown/shrunk in the XY plane by the configured value " "(negative = inwards, positive = outwards). This might be useful for fine-" "tuning hole sizes." msgstr "" "The object will be grown/shrunk in the XY plane by the configured value " "(negative = inwards, positive = outwards). This might be useful for fine-" "tuning hole sizes." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1742 msgid "Z offset" msgstr "Z offset" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1743 msgid "" "This value will be added (or subtracted) from all the Z coordinates in the " "output G-code. It is used to compensate for bad Z endstop position: for " "example, if your endstop zero actually leaves the nozzle 0.3mm far from the " "print bed, set this to -0.3 (or fix your endstop)." msgstr "" "This value will be added (or subtracted) from all the Z coordinates in the " "output G-code. It is used to compensate for bad Z endstop position: for " "example, if your endstop zero actually leaves the nozzle 0.3mm far from the " "print bed, set this to -0.3 (or fix your endstop)." #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:137 msgid "None" msgstr "None" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:138 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:80 msgid "Perimeter" msgstr "Perimeter" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:139 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:81 msgid "External perimeter" msgstr "External perimeter" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:140 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:82 msgid "Overhang perimeter" msgstr "Overhang perimeter" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:141 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:83 msgid "Internal infill" msgstr "Internal infill" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:144 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:86 msgid "Bridge infill" msgstr "Bridge infill" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:151 msgid "Mixed" msgstr "Mixed" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:330 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:68 msgid "Feature type" msgstr "Feature type" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:332 msgid "Height (mm)" msgstr "Height (mm)" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:334 msgid "Width (mm)" msgstr "Width (mm)" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:336 msgid "Speed (mm/s)" msgstr "Speed (mm/s)" #: c:\src\Slic3r\xs\src\libslic3r\GCode\PreviewData.cpp:338 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:72 msgid "Tool" msgstr "Tool" #: c:\src\Slic3r\lib\Slic3r\GUI.pm:286 msgid "Choose one or more files (STL/OBJ/AMF/3MF/PRUSA):" msgstr "Choose one or more files (STL/OBJ/AMF/3MF/PRUSA):" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:66 msgid "Version " msgstr "Version " #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:66 msgid "" " - Remember to check for updates at http://github.com/prusa3d/slic3r/releases" msgstr "" " - Remember to check for updates at http://github.com/prusa3d/slic3r/releases" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:118 msgid "Plater" msgstr "Plater" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:120 msgid "Controller" msgstr "Controller" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:192 msgid "No Bonjour device found" msgstr "No Bonjour device found" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:192 msgid "Device Browser" msgstr "Device Browser" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:211 msgid "Connection to OctoPrint works correctly." msgstr "Connection to OctoPrint works correctly." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:214 msgid "I wasn't able to connect to OctoPrint (" msgstr "I wasn't able to connect to OctoPrint (" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:215 msgid "). Check hostname and OctoPrint version (at least 1.1.0 is required)." msgstr "). Check hostname and OctoPrint version (at least 1.1.0 is required)." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:251 msgid "Open STL/OBJ/AMF…\tCtrl+O" msgstr "Open STL/OBJ/AMF…\tCtrl+O" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:251 msgid "Open a model" msgstr "Open a model" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:254 msgid "&Load Config…\tCtrl+L" msgstr "&Load Config…\tCtrl+L" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:254 msgid "Load exported configuration file" msgstr "Load exported configuration file" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:257 msgid "&Export Config…\tCtrl+E" msgstr "&Export Config…\tCtrl+E" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:257 msgid "Export current configuration to file" msgstr "Export current configuration to file" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:260 msgid "&Load Config Bundle…" msgstr "&Load Config Bundle…" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:260 msgid "Load presets from a bundle" msgstr "Load presets from a bundle" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:263 msgid "&Export Config Bundle…" msgstr "&Export Config Bundle…" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:263 msgid "Export all presets to file" msgstr "Export all presets to file" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:268 msgid "Q&uick Slice…\tCtrl+U" msgstr "Q&uick Slice…\tCtrl+U" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:268 msgid "Slice a file into a G-code" msgstr "Slice a file into a G-code" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:274 msgid "Quick Slice and Save &As…\tCtrl+Alt+U" msgstr "Quick Slice and Save &As…\tCtrl+Alt+U" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:274 msgid "Slice a file into a G-code, save as" msgstr "Slice a file into a G-code, save as" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:280 msgid "&Repeat Last Quick Slice\tCtrl+Shift+U" msgstr "&Repeat Last Quick Slice\tCtrl+Shift+U" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:280 msgid "Repeat last quick slice" msgstr "Repeat last quick slice" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:287 msgid "Slice to SV&G…\tCtrl+G" msgstr "Slice to SV&G…\tCtrl+G" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:287 msgid "Slice file to a multi-layer SVG" msgstr "Slice file to a multi-layer SVG" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:291 msgid "(&Re)Slice Now\tCtrl+S" msgstr "(&Re)Slice Now\tCtrl+S" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:291 msgid "Start new slicing process" msgstr "Start new slicing process" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:294 msgid "Repair STL file…" msgstr "Repair STL file…" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:294 msgid "Automatically repair an STL file" msgstr "Automatically repair an STL file" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:299 msgid "Preferences…\tCtrl+," msgstr "Preferences…\tCtrl+," #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:299 msgid "Application preferences" msgstr "Application preferences" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:304 msgid "&Quit" msgstr "&Quit" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:304 msgid "Quit Slic3r" msgstr "Quit Slic3r" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:314 msgid "Export G-code..." msgstr "Export G-code..." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:314 msgid "Export current plate as G-code" msgstr "Export current plate as G-code" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:317 msgid "Export plate as STL..." msgstr "Export plate as STL..." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:317 msgid "Export current plate as STL" msgstr "Export current plate as STL" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:320 msgid "Export plate as AMF..." msgstr "Export plate as AMF..." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:320 msgid "Export current plate as AMF" msgstr "Export current plate as AMF" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:323 msgid "Export plate as 3MF..." msgstr "Export plate as 3MF..." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:323 msgid "Export current plate as 3MF" msgstr "Export current plate as 3MF" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:336 msgid "Select &Plater Tab\tCtrl+1" msgstr "Select &Plater Tab\tCtrl+1" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:336 msgid "Show the plater" msgstr "Show the plater" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:342 msgid "Select &Controller Tab\tCtrl+T" msgstr "Select &Controller Tab\tCtrl+T" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:342 msgid "Show the printer controller" msgstr "Show the printer controller" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:350 msgid "Select P&rint Settings Tab\tCtrl+2" msgstr "Select P&rint Settings Tab\tCtrl+2" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:350 msgid "Show the print settings" msgstr "Show the print settings" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:353 msgid "Select &Filament Settings Tab\tCtrl+3" msgstr "Select &Filament Settings Tab\tCtrl+3" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:353 msgid "Show the filament settings" msgstr "Show the filament settings" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:356 msgid "Select Print&er Settings Tab\tCtrl+4" msgstr "Select Print&er Settings Tab\tCtrl+4" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:356 msgid "Show the printer settings" msgstr "Show the printer settings" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:368 msgid "Iso" msgstr "Iso" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:368 msgid "Iso View" msgstr "Iso View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:369 msgid "Top View" msgstr "Top View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:370 msgid "Bottom View" msgstr "Bottom View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:371 msgid "Front" msgstr "Front" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:371 msgid "Front View" msgstr "Front View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:372 msgid "Rear" msgstr "Rear" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:372 msgid "Rear View" msgstr "Rear View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:373 msgid "Left" msgstr "Left" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:373 msgid "Left View" msgstr "Left View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:374 msgid "Right" msgstr "Right" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:374 msgid "Right View" msgstr "Right View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:380 msgid "&Configuration " msgstr "&Configuration " #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:380 msgid "Run Configuration " msgstr "Run Configuration " #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:385 msgid "Prusa 3D Drivers" msgstr "Prusa 3D Drivers" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:385 msgid "Open the Prusa3D drivers download page in your browser" msgstr "Open the Prusa3D drivers download page in your browser" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:388 msgid "Prusa Edition Releases" msgstr "Prusa Edition Releases" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:388 msgid "Open the Prusa Edition releases page in your browser" msgstr "Open the Prusa Edition releases page in your browser" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:395 msgid "Slic3r &Website" msgstr "Slic3r &Website" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:395 msgid "Open the Slic3r website in your browser" msgstr "Open the Slic3r website in your browser" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:398 msgid "Slic3r &Manual" msgstr "Slic3r &Manual" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:398 msgid "Open the Slic3r manual in your browser" msgstr "Open the Slic3r manual in your browser" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:402 msgid "System Info" msgstr "System Info" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:402 msgid "Show system information" msgstr "Show system information" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:405 msgid "Report an Issue" msgstr "Report an Issue" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:405 msgid "Report an issue on the Slic3r Prusa Edition" msgstr "Report an issue on the Slic3r Prusa Edition" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:408 msgid "&About Slic3r" msgstr "&About Slic3r" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:408 msgid "Show about dialog" msgstr "Show about dialog" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:418 msgid "&File" msgstr "&File" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:419 msgid "&Plater" msgstr "&Plater" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:420 msgid "&Object" msgstr "&Object" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:421 msgid "&Window" msgstr "&Window" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:422 msgid "&View" msgstr "&View" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:426 msgid "&Help" msgstr "&Help" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:457 msgid "Choose a file to slice (STL/OBJ/AMF/3MF/PRUSA):" msgstr "Choose a file to slice (STL/OBJ/AMF/3MF/PRUSA):" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:469 msgid "No previously sliced file." msgstr "No previously sliced file." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:474 msgid "Previously sliced file (" msgstr "Previously sliced file (" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:474 msgid ") not found." msgstr ") not found." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:475 msgid "File Not Found" msgstr "File Not Found" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:514 msgid "SVG" msgstr "SVG" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:514 msgid "G-code" msgstr "G-code" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:514 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1645 msgid " file as:" msgstr " file as:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:528 msgid "Slicing…" msgstr "Slicing…" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:528 msgid "Processing " msgstr "Processing " #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:548 msgid " was successfully sliced." msgstr " was successfully sliced." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:550 msgid "Slicing Done!" msgstr "Slicing Done!" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:566 msgid "Select the STL file to repair:" msgstr "Select the STL file to repair:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:580 msgid "Save OBJ file (less prone to coordinate errors than STL) as:" msgstr "Save OBJ file (less prone to coordinate errors than STL) as:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:594 msgid "Your file was repaired." msgstr "Your file was repaired." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:594 msgid "Repair" msgstr "Repair" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:605 msgid "Save configuration as:" msgstr "Save configuration as:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:623 #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:667 msgid "Select configuration to load:" msgstr "Select configuration to load:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:646 msgid "Save presets bundle as:" msgstr "Save presets bundle as:" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:687 #, perl-format msgid "%d presets successfully imported." msgstr "%d presets successfully imported." #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:749 msgid "You have unsaved changes " msgstr "You have unsaved changes " #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:749 msgid ". Discard changes and continue anyway?" msgstr ". Discard changes and continue anyway?" #: c:\src\Slic3r\lib\Slic3r\GUI\MainFrame.pm:750 msgid "Unsaved Presets" msgstr "Unsaved Presets" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:104 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2124 msgid "3D" msgstr "3D" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:138 msgid "2D" msgstr "2D" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:157 msgid "Layers" msgstr "Layers" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:177 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:195 msgid "Add…" msgstr "Add…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:179 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:197 msgid "Delete All" msgstr "Delete All" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:180 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:198 msgid "Arrange" msgstr "Arrange" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:182 msgid "More" msgstr "More" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:183 msgid "Fewer" msgstr "Fewer" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:185 msgid "45° ccw" msgstr "45° ccw" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:186 msgid "45° cw" msgstr "45° cw" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:187 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:203 msgid "Scale…" msgstr "Scale…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:188 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:204 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2099 msgid "Split" msgstr "Split" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:189 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:205 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2102 msgid "Cut…" msgstr "Cut…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:191 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:206 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2106 msgid "Settings…" msgstr "Settings…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:192 msgid "Layer Editing" msgstr "Layer Editing" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:207 msgid "Layer editing" msgstr "Layer editing" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:220 msgid "Name" msgstr "Name" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:221 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:900 msgid "Copies" msgstr "Copies" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:222 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1056 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1061 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2068 msgid "Scale" msgstr "Scale" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:236 msgid "Export G-code…" msgstr "Export G-code…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:237 msgid "Slice now" msgstr "Slice now" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:238 msgid "Print…" msgstr "Print…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:239 msgid "Send to printer" msgstr "Send to printer" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:240 msgid "Export STL…" msgstr "Export STL…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:367 msgid "Print settings" msgstr "Print settings" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:369 msgid "Printer" msgstr "Printer" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:398 msgid "Info" msgstr "Info" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:409 msgid "Volume" msgstr "Volume" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:410 msgid "Facets" msgstr "Facets" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:411 msgid "Materials" msgstr "Materials" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:412 msgid "Manifold" msgstr "Manifold" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:438 msgid "Sliced Info" msgstr "Sliced Info" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:447 msgid "Used Filament (m)" msgstr "Used Filament (m)" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:448 msgid "Used Filament (mm³)" msgstr "Used Filament (mm³)" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:449 msgid "Used Filament (g)" msgstr "Used Filament (g)" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:451 msgid "Estimated printing time" msgstr "Estimated printing time" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:629 msgid "Loading…" msgstr "Loading…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:629 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:643 msgid "Processing input file\n" msgstr "Processing input file\n" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:663 msgid "" "This file contains several objects positioned at multiple heights. Instead " "of considering them as multiple objects, should I consider\n" "this file as a single object having multiple parts?\n" msgstr "" "This file contains several objects positioned at multiple heights. Instead " "of considering them as multiple objects, should I consider\n" "this file as a single object having multiple parts?\n" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:666 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:683 msgid "Multi-part object detected" msgstr "Multi-part object detected" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:680 msgid "" "Multiple objects were loaded for a multi-material printer.\n" "Instead of considering them as multiple objects, should I consider\n" "these files to represent a single object having multiple parts?\n" msgstr "" "Multiple objects were loaded for a multi-material printer.\n" "Instead of considering them as multiple objects, should I consider\n" "these files to represent a single object having multiple parts?\n" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:692 msgid "Loaded " msgstr "Loaded " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:744 msgid "" "Your object appears to be too large, so it was automatically scaled down to " "fit your print bed." msgstr "" "Your object appears to be too large, so it was automatically scaled down to " "fit your print bed." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:745 msgid "Object too large?" msgstr "Object too large?" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:900 msgid "Enter the number of copies of the selected object:" msgstr "Enter the number of copies of the selected object:" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:927 msgid "" "\n" "Non-positive value." msgstr "" "\n" "Non-positive value." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:928 msgid "" "\n" "Not a numeric value." msgstr "" "\n" "Not a numeric value." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:929 msgid "Slic3r Error" msgstr "Slic3r Error" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:950 msgid "Enter the rotation angle:" msgstr "Enter the rotation angle:" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:950 msgid "Rotate around " msgstr "Rotate around " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:950 msgid "Invalid rotation angle entered" msgstr "Invalid rotation angle entered" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1030 #, perl-format msgid "Enter the new size for the selected object (print bed: %smm):" msgstr "Enter the new size for the selected object (print bed: %smm):" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1031 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1035 msgid "Scale along " msgstr "Scale along " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1031 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1035 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1056 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1061 msgid "Invalid scaling value entered" msgstr "Invalid scaling value entered" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1035 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1061 #, no-perl-format msgid "Enter the scale % for the selected object:" msgstr "Enter the scale % for the selected object:" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1056 msgid "Enter the new max size for the selected object:" msgstr "Enter the new max size for the selected object:" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1112 msgid "" "The selected object can't be split because it contains more than one volume/" "material." msgstr "" "The selected object can't be split because it contains more than one volume/" "material." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1121 msgid "" "The selected object couldn't be split because it contains only one part." msgstr "" "The selected object couldn't be split because it contains only one part." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1286 msgid "Slicing cancelled" msgstr "Slicing cancelled" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1300 msgid "Another export job is currently running." msgstr "Another export job is currently running." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1445 msgid "File added to print queue" msgstr "File added to print queue" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1448 msgid "Sending G-code file to the OctoPrint server..." msgstr "Sending G-code file to the OctoPrint server..." #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1451 msgid "G-code file exported to " msgstr "G-code file exported to " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1454 msgid "Export failed" msgstr "Export failed" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1524 msgid "G-code file successfully uploaded to the OctoPrint server" msgstr "G-code file successfully uploaded to the OctoPrint server" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1526 msgid "Error while uploading to the OctoPrint server: " msgstr "Error while uploading to the OctoPrint server: " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1539 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1581 msgid "STL file exported to " msgstr "STL file exported to " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1592 msgid "AMF file exported to " msgstr "AMF file exported to " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1596 msgid "Error exporting AMF file " msgstr "Error exporting AMF file " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1608 msgid "3MF file exported to " msgstr "3MF file exported to " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1612 msgid "Error exporting 3MF file " msgstr "Error exporting 3MF file " #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1958 #, perl-format msgid "%d (%d shells)" msgstr "%d (%d shells)" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1960 #, perl-format msgid "Auto-repaired (%d errors)" msgstr "Auto-repaired (%d errors)" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1965 #, perl-format msgid "" "%d degenerate facets, %d edges fixed, %d facets removed, %d facets added, %d " "facets reversed, %d backwards edges" msgstr "" "%d degenerate facets, %d edges fixed, %d facets removed, %d facets added, %d " "facets reversed, %d backwards edges" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:1970 msgid "Yes" msgstr "Yes" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2021 msgid "Remove the selected object" msgstr "Remove the selected object" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2024 msgid "Increase copies" msgstr "Increase copies" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2024 msgid "Place one more copy of the selected object" msgstr "Place one more copy of the selected object" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2027 msgid "Decrease copies" msgstr "Decrease copies" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2027 msgid "Remove one copy of the selected object" msgstr "Remove one copy of the selected object" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2030 msgid "Set number of copies…" msgstr "Set number of copies…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2030 msgid "Change the number of copies of the selected object" msgstr "Change the number of copies of the selected object" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2034 msgid "Rotate 45° clockwise" msgstr "Rotate 45° clockwise" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2034 msgid "Rotate the selected object by 45° clockwise" msgstr "Rotate the selected object by 45° clockwise" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2037 msgid "Rotate 45° counter-clockwise" msgstr "Rotate 45° counter-clockwise" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2037 msgid "Rotate the selected object by 45° counter-clockwise" msgstr "Rotate the selected object by 45° counter-clockwise" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2042 msgid "Rotate" msgstr "Rotate" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2042 msgid "Rotate the selected object by an arbitrary angle" msgstr "Rotate the selected object by an arbitrary angle" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2044 msgid "Around X axis…" msgstr "Around X axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2044 msgid "Rotate the selected object by an arbitrary angle around X axis" msgstr "Rotate the selected object by an arbitrary angle around X axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2047 msgid "Around Y axis…" msgstr "Around Y axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2047 msgid "Rotate the selected object by an arbitrary angle around Y axis" msgstr "Rotate the selected object by an arbitrary angle around Y axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2050 msgid "Around Z axis…" msgstr "Around Z axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2050 msgid "Rotate the selected object by an arbitrary angle around Z axis" msgstr "Rotate the selected object by an arbitrary angle around Z axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2055 msgid "Mirror" msgstr "Mirror" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2055 msgid "Mirror the selected object" msgstr "Mirror the selected object" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2057 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2073 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2089 msgid "Along X axis…" msgstr "Along X axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2057 msgid "Mirror the selected object along the X axis" msgstr "Mirror the selected object along the X axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2060 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2076 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2092 msgid "Along Y axis…" msgstr "Along Y axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2060 msgid "Mirror the selected object along the Y axis" msgstr "Mirror the selected object along the Y axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2063 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2079 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2095 msgid "Along Z axis…" msgstr "Along Z axis…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2063 msgid "Mirror the selected object along the Z axis" msgstr "Mirror the selected object along the Z axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2068 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2084 msgid "Scale the selected object along a single axis" msgstr "Scale the selected object along a single axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2070 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2086 msgid "Uniformly…" msgstr "Uniformly…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2070 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2086 msgid "Scale the selected object along the XYZ axes" msgstr "Scale the selected object along the XYZ axes" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2073 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2089 msgid "Scale the selected object along the X axis" msgstr "Scale the selected object along the X axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2076 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2092 msgid "Scale the selected object along the Y axis" msgstr "Scale the selected object along the Y axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2079 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2095 msgid "Scale the selected object along the Z axis" msgstr "Scale the selected object along the Z axis" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2084 msgid "Scale to size" msgstr "Scale to size" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2099 msgid "Split the selected object into individual parts" msgstr "Split the selected object into individual parts" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2102 msgid "Open the 3D cutting tool" msgstr "Open the 3D cutting tool" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2106 msgid "Open the object editor dialog" msgstr "Open the object editor dialog" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2110 msgid "Reload from Disk" msgstr "Reload from Disk" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2110 msgid "Reload the selected file from Disk" msgstr "Reload the selected file from Disk" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2113 msgid "Export object as STL…" msgstr "Export object as STL…" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater.pm:2113 msgid "Export this single object as STL file" msgstr "Export this single object as STL file" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\2D.pm:131 msgid "What do you want to print today? ™" msgstr "What do you want to print today? ™" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\2D.pm:132 msgid "Drag your objects here" msgstr "Drag your objects here" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:63 msgid "1 Layer" msgstr "1 Layer" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:65 msgid "View" msgstr "View" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:75 msgid "Show" msgstr "Show" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:78 #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:79 msgid "Feature types" msgstr "Feature types" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:96 msgid "Retractions" msgstr "Retractions" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:97 msgid "Unretractions" msgstr "Unretractions" #: c:\src\Slic3r\lib\Slic3r\GUI\Plater\3DPreview.pm:98 msgid "Shells" msgstr "Shells"