PAT9125 I2C, hardware SG homing

separate pin configuration file for each board
changed board codes:
RAMBO =100, MiniRambo1.0 =200, MiniRambo1.3 = 203, Einy03 =303, Einy04 =304

1 files changed, 102 insertions, 0 deletions

diff --git a/Firmware/pins_Rambo_1_3.h b/Firmware/pins_Rambo_1_3.h
new file mode 100644
index 000000000..3e9c45dae
--- /dev/null
+++ b/Firmware/pins_Rambo_1_3.h
@@ -0,0 +1,102 @@
+/*****************************************************************
+* Rambo mini 1.3 Pin Assignments
+******************************************************************/
+
+#define ELECTRONICS "RAMBo13a"
+
+#define KNOWN_BOARD
+#ifndef __AVR_ATmega2560__
+  #error Oops!  Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
+#endif
+
+#define FR_SENS                21
+
+#define X_STEP_PIN             37
+#define X_DIR_PIN              48
+#define X_MIN_PIN              12
+#define X_MAX_PIN              30
+#define X_ENABLE_PIN           29
+#define X_MS1_PIN              40
+#define X_MS2_PIN              41
+#define Y_STEP_PIN             36
+#define Y_DIR_PIN              49
+#define Y_MIN_PIN              11
+#define Y_MAX_PIN              24
+#define Y_ENABLE_PIN           28
+#define Y_MS1_PIN              69
+#define Y_MS2_PIN              39
+#define Z_STEP_PIN             35
+#define Z_DIR_PIN              47
+#define Z_MIN_PIN              10
+#define Z_MAX_PIN              23
+#define Z_ENABLE_PIN           27
+#define Z_MS1_PIN              68
+#define Z_MS2_PIN              67
+#define TEMP_BED_PIN            2
+#define TEMP_0_PIN              0
+#define HEATER_1_PIN            7
+#define TEMP_1_PIN              1
+#define TEMP_2_PIN             -1
+
+#ifdef SNMM 
+  #define E_MUX0_PIN           17
+  #define E_MUX1_PIN           16
+  #define E_MUX2_PIN           84
+#endif
+
+#ifdef DIS
+  #define D_REQUIRE            30
+  #define D_DATA               20
+  #define D_DATACLOCK          21
+#endif
+
+// The SDSS pin uses a different pin mapping from file Sd2PinMap.h
+#define SDSS                   53
+
+#ifndef SDSUPPORT
+// these pins are defined in the SD library if building with SD support
+  #define SCK_PIN              52
+  #define MISO_PIN             50
+  #define MOSI_PIN             51
+#endif
+
+#define BEEPER                 84
+
+#define BTN_EN1                72
+#define BTN_EN2                14
+#define BTN_ENC                 9
+
+#define SDCARDDETECT           15
+
+#define LCD_PINS_RS            82
+#define LCD_PINS_ENABLE        18
+#define LCD_PINS_D4            19
+#define LCD_PINS_D5            70
+#define LCD_PINS_D6            85
+#define LCD_PINS_D7            71
+
+#define E0_STEP_PIN            34
+#define E0_DIR_PIN             43
+#define E0_ENABLE_PIN          26
+#define E0_MS1_PIN             65
+#define E0_MS2_PIN             66
+#define LED_PIN                13
+
+#ifdef THREEMM_PRINTER
+  #define FAN_PIN               8
+#else
+  #define FAN_PIN               6
+#endif
+
+#define KILL_PIN               -1 //80 with Smart Controller LCD
+#define SUICIDE_PIN            -1  //PIN that has to be turned on right after start, to keep power flowing.
+#define SDPOWER                -1
+#define HEATER_2_PIN           -1
+
+#define HEATER_0_PIN            3
+#define HEATER_BED_PIN          4
+#define FAN_1_PIN              -1 //6
+#define PS_ON_PIN              71
+#define MOTOR_CURRENT_PWM_XY_PIN   46
+#define MOTOR_CURRENT_PWM_Z_PIN    45
+#define MOTOR_CURRENT_PWM_E_PIN    44