1 files changed, 130 insertions, 0 deletions
diff --git a/Firmware/pins_Einy_0_3.h b/Firmware/pins_Einy_0_3.h
new file mode 100644
index 000000000..d59761a12
--- /dev/null
+++ b/Firmware/pins_Einy_0_3.h
@@ -0,0 +1,130 @@
+/*****************************************************************
+* EINY Rambo 0.3a Pin Assignments
+******************************************************************/
+
+#define ELECTRONICS "EINY_03a"
+
+#define KNOWN_BOARD
+#ifndef __AVR_ATmega2560__
+  #error Oops!  Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu.
+#endif
+
+#define TMC2130
+#define PAT9125
+
+#define SWI2C                    // enable software i2c
+#define SWI2C_A8                 // 8bit address functions
+
+#define PAT9125_SWI2C
+#define PAT9125_SWI2C_SDA   20 //SDA on P3
+#define PAT9125_SWI2C_SCL   21 //SCL on P3
+#define PAT9125_SWI2C_CFG   0xb1 //2us clock delay, 2048 cycles timeout
+
+//#define SWSPI_MISO          16 //RX2
+//#define SWSPI_MOSI          16 //RX2
+//#define SWSPI_SCK           17 //TX2
+//#define SWSPI_CS            20 //SDA
+
+////#define SWI2C_SDA           20 //SDA
+////#define SWI2C_SCL           21 //SCL
+//#define SWI2C_SDA           16 //RX2
+//#define SWI2C_SCL           17 //TX2
+
+#define X_TMC2130_CS        41
+#define X_TMC2130_DIAG      40
+#define X_STEP_PIN          37
+#define X_DIR_PIN           49
+//#define X_MIN_PIN           12
+//#define X_MAX_PIN           30
+#define X_MIN_PIN           X_TMC2130_DIAG
+#define X_MAX_PIN           X_TMC2130_DIAG
+#define X_ENABLE_PIN        29
+#define X_MS1_PIN           -1
+#define X_MS2_PIN           -1
+
+#define Y_TMC2130_CS        39
+#define Y_TMC2130_DIAG      69
+#define Y_STEP_PIN          36
+#define Y_DIR_PIN           48
+//#define Y_MIN_PIN           11
+//#define Y_MAX_PIN           24
+#define Y_MIN_PIN           Y_TMC2130_DIAG
+#define Y_MAX_PIN           Y_TMC2130_DIAG
+#define Y_ENABLE_PIN        28
+#define Y_MS1_PIN           -1
+#define Y_MS2_PIN           -1
+
+#define Z_TMC2130_CS        67
+#define Z_TMC2130_DIAG      68
+#define Z_STEP_PIN          35
+#define Z_DIR_PIN           47
+#define Z_MIN_PIN           10
+#define Z_MAX_PIN           23
+//#define Z_MAX_PIN           Z_TMC2130_DIAG
+#define Z_ENABLE_PIN        27
+#define Z_MS1_PIN           -1
+#define Z_MS2_PIN           -1
+
+#define HEATER_BED_PIN       4
+#define TEMP_BED_PIN         2
+
+#define HEATER_0_PIN         3
+#define TEMP_0_PIN           0
+
+#define HEATER_1_PIN         7
+#define TEMP_1_PIN           1
+
+#ifdef BARICUDA
+#define HEATER_2_PIN         6
+#else
+#define HEATER_2_PIN        -1
+#endif
+
+#define TEMP_2_PIN          -1
+
+#define E0_TMC2130_CS       66
+#define E0_TMC2130_DIAG     65
+#define E0_STEP_PIN         34
+#define E0_DIR_PIN          43
+#define E0_ENABLE_PIN       26
+#define E0_MS1_PIN          -1
+#define E0_MS2_PIN          -1
+
+#define MOTOR_CURRENT_PWM_XY_PIN 46
+#define MOTOR_CURRENT_PWM_Z_PIN  45
+#define MOTOR_CURRENT_PWM_E_PIN  44
+#define SDPOWER             -1
+#define SDSS                53
+#define LED_PIN             13
+#define FAN_PIN              6
+#define FAN_1_PIN           -1
+#define PS_ON_PIN           -1
+#define KILL_PIN            -1  // 80 with Smart Controller LCD
+#define SUICIDE_PIN         -1  // PIN that has to be turned on right after start, to keep power flowing.
+
+#ifdef ULTRA_LCD
+
+//#define KILL_PIN            32
+
+#ifdef NEWPANEL
+
+#define BEEPER              84  // Beeper on AUX-4
+#define LCD_PINS_RS         82
+#define LCD_PINS_ENABLE     18
+#define LCD_PINS_D4         19
+#define LCD_PINS_D5         70
+#define LCD_PINS_D6         85
+#define LCD_PINS_D7         71
+
+//buttons are directly attached using AUX-2
+#define BTN_EN1             72
+#define BTN_EN2             14
+#define BTN_ENC              9  // the click
+
+#define SDCARDDETECT        15
+
+#define TACH_0              81
+#define TACH_1              80 
+
+#endif //NEWPANEL
+#endif //ULTRA_LCD