diff options
Diffstat (limited to 'Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h')
| -rw-r--r-- | Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h | 29 |
1 files changed, 16 insertions, 13 deletions
diff --git a/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h b/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h index ff4340148..129ec848c 100644 --- a/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h +++ b/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h @@ -67,11 +67,10 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o //#define DEFAULT_MAX_FEEDRATE {400, 400, 12, 120} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {500, 500, 12, 120} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {2000, 2000, 250, 5000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for retracts +#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts #define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) //#define MAX_SILENT_FEEDRATE 2700 // @@ -83,8 +82,10 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o #define DEBUG_DISABLE_STARTMSGS //no startup messages #define DEBUG_DISABLE_MINTEMP //mintemp error ignored #define DEBUG_DISABLE_SWLIMITS //sw limits ignored +#define DEBUG_DISABLE_LCD_STATUS_LINE //sw limits ignored #define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed -#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) +#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages +//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) //#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) //#define DEBUG_BLINK_ACTIVE #endif @@ -118,22 +119,22 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o #define TMC2130_PWM_FREQ_E 2 // PWMCONF */ -//#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk) +//#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410) +#define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410) +#define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk) -#define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode -#define TMC2130_THIGH 0 // THIGH - unused +#define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode +#define TMC2130_THIGH 0 // THIGH - unused #define TMC2130_TCOOLTHRS 239 // TCOOLTHRS - coolstep treshold #define TMC2130_SG_HOMING 1 // stallguard homing -#define TMC2130_SG_HOMING_SW 1 // stallguard "software" homing +//#define TMC2130_SG_HOMING_SW 1 // stallguard "software" homing #define TMC2130_SG_THRS_X 30 // stallguard sensitivity for X axis #define TMC2130_SG_THRS_Y 30 // stallguard sensitivity for Y axis -#define TMC2130_SG_DELTA 128 // stallguard delta [usteps] (minimum usteps before stallguard readed) +#define TMC2130_SG_DELTA 128 // stallguard delta [usteps] (minimum usteps before stallguard readed - SW homing) -//new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right +//new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right (Z axis only) #define TMC2130_CURRENTS_H {3, 3, 5, 8} // default holding currents for all axes #define TMC2130_CURRENTS_R {13, 13, 20, 20} // default running currents for all axes @@ -464,4 +465,6 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o #define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print #endif +#define UVLO_Z_AXIS_SHIFT 2 + #endif //__CONFIGURATION_PRUSA_H |