| Age | Commit message (Expand) | Author |
|---|
| 2017-08-21 | TMC2130 stallguard improovment - axis load monitoring, autocalibrate Z. | Robert Pelnar |
| 2017-08-17 | PAT9125 I2C, hardware SG homing | Robert Pelnar |
| 2017-07-12 | Merge branch 'MK3' into MK3 | XPila |
| 2017-07-12 | TMC2130 stallguard SW homing improvement - steps delta instead of delay (loop... | Robert Pelnar |
| 2017-07-07 | Merge branch 'MK3' into MK3-michal | michalprusa |
| 2017-07-07 | filament sensor tweaked for 400 step motor. | michalprusa |
| 2017-07-07 | Merge pull request #20 from XPila/MK3 | XPila |
| 2017-07-07 | SG homing - fixed bug - set sg_homing_delay to zero before move. | Robert Pelnar |
| 2017-07-07 | PAT9125 finally able to turn off | michalprusa |
| 2017-07-07 | PAT9125 init result print | michalprusa |
| 2017-07-07 | Merge remote-tracking branch 'origin/MK3-michal' into MK3-michal | michalprusa |
| 2017-07-07 | Merge branch 'MK3' into MK3-michal | XPila |
| 2017-07-07 | Power panic improved by turning off Z steppers | michalprusa |
| 2017-07-07 | Merge pull request #16 from XPila/MK3 | XPila |
| 2017-07-07 | pat9125 filament sensor | Robert Pelnar |
| 2017-07-07 | Merge remote-tracking branch 'origin/MK3' into MK3-michal | michalprusa |
| 2017-07-07 | Linear Advance | michalprusa |
| 2017-07-07 | power panic: extrusion to stabilize pressure, waiting for temperature in homi... | PavelSindler |
| 2017-07-06 | status message during print recovery | PavelSindler |
| 2017-07-06 | updated z recovery in power panic, added test to main menu | PavelSindler |
| 2017-07-06 | changed Z axis recovery in power panic | PavelSindler |
| 2017-07-06 | power panic - fixed z axis recovery | PavelSindler |
| 2017-07-06 | Merge pull request #10 from XPila/MK3 | XPila |
| 2017-07-06 | Changed jerks, disabled oversampling, debug code, commands for seting pwm_amp... | Robert Pelnar |
| 2017-07-06 | Merge branch 'MK3' into MK3 | XPila |
| 2017-07-05 | current feedrate and fan speed stored to eeprom in power panic, number of blo... | PavelSindler |
| 2017-07-05 | fixed SD card restore position (power panic) | PavelSindler |
| 2017-07-04 | power panic: Z axis is lowered in position where print starts (is recovered) | PavelSindler |
| 2017-07-04 | Merge branch 'MK3' of github.com:prusa3d/Prusa-Firmware-DEV into MK3 | Andre Sklenar |
| 2017-07-04 | Init LCD ASAP for a nice UX | Andre Sklenar |
| 2017-07-04 | DEBUG defines, variant files for MK3 | Robert Pelnar |
| 2017-07-04 | recover print | PavelSindler |
| 2017-07-03 | Merge remote-tracking branch 'upstream/MK3' into MK3 | PavelSindler |
| 2017-07-03 | added debug messages for serial | PavelSindler |
| 2017-07-03 | TMC2130 stallguard homing - sg_thrs_x and sg_thrs_y - command M916, lcd_silen... | Robert Pelnar |
| 2017-07-03 | TMC2130 tuning, silent/high power mode | Robert Pelnar |
| 2017-07-03 | TMC2130 tunning, overtemp | Robert Pelnar |
| 2017-07-02 | saving/restoring filename and current position in bytes to eeprom, UVLO changed | PavelSindler |
| 2017-07-02 | position saving and restoring in UVLO | PavelSindler |
| 2017-07-01 | sync with upstream | PavelSindler |
| 2017-07-01 | uvlo initial version | PavelSindler |
| 2017-07-01 | TMC2130 + software SG homing + LF lineendings + tmc2130 debug M-Codes | Robert Pelnar |
| 2017-06-29 | 3.0.12-RC2 sync | PavelSindler |
| 2017-06-28 | fan speed check initial version, selftest updated | PavelSindler |
| 2017-06-17 | Filament sensor PAT9125 implemented | michalprusa |
| 2017-06-17 | StallGuard homing implemented, working | michalprusa |
| 2017-06-17 | Johhny Firmware sync | michalprusa |
| 2017-03-24 | 3.0.10 sync | michalprusa |
| 2016-09-01 | Fixed a missing SD card error on start up, if the setup was blocked | bubnikv |
| 2016-09-01 | Removed the non-working pressure advance feature. | bubnikv |
