blob: d59761a1229bcd025555d51b1ba42019291d4b76 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*****************************************************************
* EINY Rambo 0.3a Pin Assignments
******************************************************************/
#define ELECTRONICS "EINY_03a"
#define KNOWN_BOARD
#ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu.
#endif
#define TMC2130
#define PAT9125
#define SWI2C // enable software i2c
#define SWI2C_A8 // 8bit address functions
#define PAT9125_SWI2C
#define PAT9125_SWI2C_SDA 20 //SDA on P3
#define PAT9125_SWI2C_SCL 21 //SCL on P3
#define PAT9125_SWI2C_CFG 0xb1 //2us clock delay, 2048 cycles timeout
//#define SWSPI_MISO 16 //RX2
//#define SWSPI_MOSI 16 //RX2
//#define SWSPI_SCK 17 //TX2
//#define SWSPI_CS 20 //SDA
////#define SWI2C_SDA 20 //SDA
////#define SWI2C_SCL 21 //SCL
//#define SWI2C_SDA 16 //RX2
//#define SWI2C_SCL 17 //TX2
#define X_TMC2130_CS 41
#define X_TMC2130_DIAG 40
#define X_STEP_PIN 37
#define X_DIR_PIN 49
//#define X_MIN_PIN 12
//#define X_MAX_PIN 30
#define X_MIN_PIN X_TMC2130_DIAG
#define X_MAX_PIN X_TMC2130_DIAG
#define X_ENABLE_PIN 29
#define X_MS1_PIN -1
#define X_MS2_PIN -1
#define Y_TMC2130_CS 39
#define Y_TMC2130_DIAG 69
#define Y_STEP_PIN 36
#define Y_DIR_PIN 48
//#define Y_MIN_PIN 11
//#define Y_MAX_PIN 24
#define Y_MIN_PIN Y_TMC2130_DIAG
#define Y_MAX_PIN Y_TMC2130_DIAG
#define Y_ENABLE_PIN 28
#define Y_MS1_PIN -1
#define Y_MS2_PIN -1
#define Z_TMC2130_CS 67
#define Z_TMC2130_DIAG 68
#define Z_STEP_PIN 35
#define Z_DIR_PIN 47
#define Z_MIN_PIN 10
#define Z_MAX_PIN 23
//#define Z_MAX_PIN Z_TMC2130_DIAG
#define Z_ENABLE_PIN 27
#define Z_MS1_PIN -1
#define Z_MS2_PIN -1
#define HEATER_BED_PIN 4
#define TEMP_BED_PIN 2
#define HEATER_0_PIN 3
#define TEMP_0_PIN 0
#define HEATER_1_PIN 7
#define TEMP_1_PIN 1
#ifdef BARICUDA
#define HEATER_2_PIN 6
#else
#define HEATER_2_PIN -1
#endif
#define TEMP_2_PIN -1
#define E0_TMC2130_CS 66
#define E0_TMC2130_DIAG 65
#define E0_STEP_PIN 34
#define E0_DIR_PIN 43
#define E0_ENABLE_PIN 26
#define E0_MS1_PIN -1
#define E0_MS2_PIN -1
#define MOTOR_CURRENT_PWM_XY_PIN 46
#define MOTOR_CURRENT_PWM_Z_PIN 45
#define MOTOR_CURRENT_PWM_E_PIN 44
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 6
#define FAN_1_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1 // 80 with Smart Controller LCD
#define SUICIDE_PIN -1 // PIN that has to be turned on right after start, to keep power flowing.
#ifdef ULTRA_LCD
//#define KILL_PIN 32
#ifdef NEWPANEL
#define BEEPER 84 // Beeper on AUX-4
#define LCD_PINS_RS 82
#define LCD_PINS_ENABLE 18
#define LCD_PINS_D4 19
#define LCD_PINS_D5 70
#define LCD_PINS_D6 85
#define LCD_PINS_D7 71
//buttons are directly attached using AUX-2
#define BTN_EN1 72
#define BTN_EN2 14
#define BTN_ENC 9 // the click
#define SDCARDDETECT 15
#define TACH_0 81
#define TACH_1 80
#endif //NEWPANEL
#endif //ULTRA_LCD
|
