Age | Commit message (Collapse) | Author |
|
After commit e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Two new drivers this cycle and a significant rework of the CMOS driver
make the bulk of the changes.
I also carry powerpc changes with the agreement of Michael.
New drivers:
- Sunplus SP7021 RTC
- Nintendo GameCube, Wii and Wii U RTC
Driver updates:
- cmos: refactor UIP handling and presence check, fix century
- rs5c372: offset correction support, report low voltage
- rv8803: Epson RX8804 support"
* tag 'rtc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
rtc: sunplus: fix return value in sp_rtc_probe()
rtc: cmos: Evaluate century appropriate
rtc: gamecube: Fix an IS_ERR() vs NULL check
rtc: mc146818-lib: fix signedness bug in mc146818_get_time()
dt-bindings: rtc: qcom-pm8xxx-rtc: update register numbers
rtc: pxa: fix null pointer dereference
rtc: ftrtc010: Use platform_get_irq() to get the interrupt
rtc: Move variable into switch case statement
rtc: pcf2127: Fix typo in comment
dt-bindings: rtc: Add Sunplus RTC json-schema
rtc: Add driver for RTC in Sunplus SP7021
rtc: rs5c372: fix incorrect oscillation value on r2221tl
rtc: rs5c372: add offset correction support
rtc: cmos: avoid UIP when writing alarm time
rtc: cmos: avoid UIP when reading alarm time
rtc: mc146818-lib: refactor mc146818_does_rtc_work
rtc: mc146818-lib: refactor mc146818_get_time
rtc: mc146818-lib: extract mc146818_avoid_UIP
rtc: mc146818-lib: fix RTC presence check
rtc: Check return value from mc146818_get_time()
...
|
|
Notice that pm_runtime_put_suppliers() cannot be called with
disabled interrupts, because it may sleep (due to the device
links read locking in the non-SRCU case), and so it can use
spin_lock_irq() and spin_unlock_irq() for the locking.
Update the function accordingly and while at it move the "put"
local variable in it into the inner block where it is used.
This change is not expected to have any visible functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
Commit 2aa36604e824 ("PM: sleep: Avoid calling put_device() under
dpm_list_mtx") forgot to update the while () loop termination
condition to also break the loop if error is nonzero, which
causes the loop to become infinite if device_prepare() returns
an error for one device.
Add the missing !error check.
Fixes: 2aa36604e824 ("PM: sleep: Avoid calling put_device() under dpm_list_mtx")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
|
|
Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.
To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.
This change is not expected to have any visible functional impact.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
|
In some cases (for example, during system-wide suspend and resume of
devices) it is useful to know whether or not runtime PM has ever been
enabled for a given device and, if so, what the runtime PM status of
it had been right before runtime PM was disabled for it last time.
For this reason, introduce a new struct dev_pm_info field called
last_status that will be used for capturing the runtime PM status of
the device when its power.disable_depth counter changes from 0 to 1.
The new field will be set to RPM_INVALID to start with and whenever
power.disable_depth changes from 1 to 0, so it will be valid only
when runtime PM of the device is currently disabled, but it has been
enabled at least once.
Immediately use power.last_status in rpm_resume() to make it handle
the case when PM runtime is disabled for the device, but its runtime
PM status is RPM_ACTIVE more consistently. Namely, make it return 1
if power.last_status is also equal to RPM_ACTIVE in that case (the
idea being that if the status was RPM_ACTIVE last time when
power.disable_depth was changing from 0 to 1 and it is still
RPM_ACTIVE, it can be assumed to reflect what happened to the device
last time when it was using runtime PM) and -EACCES otherwise.
Update the documentation to provide a description of last_status and
change the description of pm_runtime_resume() in it to reflect the
new behavior of rpm_active().
While at it, rearrange the code in pm_runtime_enable() to be more
straightforward and replace the WARN() macro in it with a pr_warn()
invocation which is less disruptive.
Link: https://lore.kernel.org/linux-pm/20211026222626.39222-1-ulf.hansson@linaro.org/t/#u
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are 4 users of mc146818_get_time() and none of them was checking
the return value from this function. Change this.
Print the appropriate warnings in callers of mc146818_get_time() instead
of in the function mc146818_get_time() itself, in order not to add
strings to rtc-mc146818-lib.c, which is kind of a library.
The callers of alpha_rtc_read_time() and cmos_read_time() may use the
contents of (struct rtc_time *) even when the functions return a failure
code. Therefore, set the contents of (struct rtc_time *) to 0x00,
which looks more sensible then 0xff and aligns with the (possibly
stale?) comment in cmos_read_time:
/*
* If pm_trace abused the RTC for storage, set the timespec to 0,
* which tells the caller that this RTC value is unusable.
*/
For consistency, do this in mc146818_get_time().
Note: hpet_rtc_interrupt() may call mc146818_get_time() many times a
second. It is very unlikely, though, that the RTC suddenly stops
working and mc146818_get_time() would consistently fail.
Only compile-tested on alpha.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-alpha@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-4-mat.jonczyk@o2.pl
|
|
It is generally unsafe to call put_device() with dpm_list_mtx held,
because the given device's release routine may carry out an action
depending on that lock which then may deadlock, so modify the
system-wide suspend and resume of devices to always drop dpm_list_mtx
before calling put_device() (and adjust white space somewhat while
at it).
For instance, this prevents the following splat from showing up in
the kernel log after a system resume in certain configurations:
[ 3290.969514] ======================================================
[ 3290.969517] WARNING: possible circular locking dependency detected
[ 3290.969519] 5.15.0+ #2420 Tainted: G S
[ 3290.969523] ------------------------------------------------------
[ 3290.969525] systemd-sleep/4553 is trying to acquire lock:
[ 3290.969529] ffff888117ab1138 ((wq_completion)hci0#2){+.+.}-{0:0}, at: flush_workqueue+0x87/0x4a0
[ 3290.969554]
but task is already holding lock:
[ 3290.969556] ffffffff8280fca8 (dpm_list_mtx){+.+.}-{3:3}, at: dpm_resume+0x12e/0x3e0
[ 3290.969571]
which lock already depends on the new lock.
[ 3290.969573]
the existing dependency chain (in reverse order) is:
[ 3290.969575]
-> #3 (dpm_list_mtx){+.+.}-{3:3}:
[ 3290.969583] __mutex_lock+0x9d/0xa30
[ 3290.969591] device_pm_add+0x2e/0xe0
[ 3290.969597] device_add+0x4d5/0x8f0
[ 3290.969605] hci_conn_add_sysfs+0x43/0xb0 [bluetooth]
[ 3290.969689] hci_conn_complete_evt.isra.71+0x124/0x750 [bluetooth]
[ 3290.969747] hci_event_packet+0xd6c/0x28a0 [bluetooth]
[ 3290.969798] hci_rx_work+0x213/0x640 [bluetooth]
[ 3290.969842] process_one_work+0x2aa/0x650
[ 3290.969851] worker_thread+0x39/0x400
[ 3290.969859] kthread+0x142/0x170
[ 3290.969865] ret_from_fork+0x22/0x30
[ 3290.969872]
-> #2 (&hdev->lock){+.+.}-{3:3}:
[ 3290.969881] __mutex_lock+0x9d/0xa30
[ 3290.969887] hci_event_packet+0xba/0x28a0 [bluetooth]
[ 3290.969935] hci_rx_work+0x213/0x640 [bluetooth]
[ 3290.969978] process_one_work+0x2aa/0x650
[ 3290.969985] worker_thread+0x39/0x400
[ 3290.969993] kthread+0x142/0x170
[ 3290.969999] ret_from_fork+0x22/0x30
[ 3290.970004]
-> #1 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}:
[ 3290.970013] process_one_work+0x27d/0x650
[ 3290.970020] worker_thread+0x39/0x400
[ 3290.970028] kthread+0x142/0x170
[ 3290.970033] ret_from_fork+0x22/0x30
[ 3290.970038]
-> #0 ((wq_completion)hci0#2){+.+.}-{0:0}:
[ 3290.970047] __lock_acquire+0x15cb/0x1b50
[ 3290.970054] lock_acquire+0x26c/0x300
[ 3290.970059] flush_workqueue+0xae/0x4a0
[ 3290.970066] drain_workqueue+0xa1/0x130
[ 3290.970073] destroy_workqueue+0x34/0x1f0
[ 3290.970081] hci_release_dev+0x49/0x180 [bluetooth]
[ 3290.970130] bt_host_release+0x1d/0x30 [bluetooth]
[ 3290.970195] device_release+0x33/0x90
[ 3290.970201] kobject_release+0x63/0x160
[ 3290.970211] dpm_resume+0x164/0x3e0
[ 3290.970215] dpm_resume_end+0xd/0x20
[ 3290.970220] suspend_devices_and_enter+0x1a4/0xba0
[ 3290.970229] pm_suspend+0x26b/0x310
[ 3290.970236] state_store+0x42/0x90
[ 3290.970243] kernfs_fop_write_iter+0x135/0x1b0
[ 3290.970251] new_sync_write+0x125/0x1c0
[ 3290.970257] vfs_write+0x360/0x3c0
[ 3290.970263] ksys_write+0xa7/0xe0
[ 3290.970269] do_syscall_64+0x3a/0x80
[ 3290.970276] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 3290.970284]
other info that might help us debug this:
[ 3290.970285] Chain exists of:
(wq_completion)hci0#2 --> &hdev->lock --> dpm_list_mtx
[ 3290.970297] Possible unsafe locking scenario:
[ 3290.970299] CPU0 CPU1
[ 3290.970300] ---- ----
[ 3290.970302] lock(dpm_list_mtx);
[ 3290.970306] lock(&hdev->lock);
[ 3290.970310] lock(dpm_list_mtx);
[ 3290.970314] lock((wq_completion)hci0#2);
[ 3290.970319]
*** DEADLOCK ***
[ 3290.970321] 7 locks held by systemd-sleep/4553:
[ 3290.970325] #0: ffff888103bcd448 (sb_writers#4){.+.+}-{0:0}, at: ksys_write+0xa7/0xe0
[ 3290.970341] #1: ffff888115a14488 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x103/0x1b0
[ 3290.970355] #2: ffff888100f719e0 (kn->active#233){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x10c/0x1b0
[ 3290.970369] #3: ffffffff82661048 (autosleep_lock){+.+.}-{3:3}, at: state_store+0x12/0x90
[ 3290.970384] #4: ffffffff82658ac8 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x9f/0x310
[ 3290.970399] #5: ffffffff827f2a48 (acpi_scan_lock){+.+.}-{3:3}, at: acpi_suspend_begin+0x4c/0x80
[ 3290.970416] #6: ffffffff8280fca8 (dpm_list_mtx){+.+.}-{3:3}, at: dpm_resume+0x12e/0x3e0
[ 3290.970428]
stack backtrace:
[ 3290.970431] CPU: 3 PID: 4553 Comm: systemd-sleep Tainted: G S 5.15.0+ #2420
[ 3290.970438] Hardware name: Dell Inc. XPS 13 9380/0RYJWW, BIOS 1.5.0 06/03/2019
[ 3290.970441] Call Trace:
[ 3290.970446] dump_stack_lvl+0x44/0x57
[ 3290.970454] check_noncircular+0x105/0x120
[ 3290.970468] ? __lock_acquire+0x15cb/0x1b50
[ 3290.970474] __lock_acquire+0x15cb/0x1b50
[ 3290.970487] lock_acquire+0x26c/0x300
[ 3290.970493] ? flush_workqueue+0x87/0x4a0
[ 3290.970503] ? __raw_spin_lock_init+0x3b/0x60
[ 3290.970510] ? lockdep_init_map_type+0x58/0x240
[ 3290.970519] flush_workqueue+0xae/0x4a0
[ 3290.970526] ? flush_workqueue+0x87/0x4a0
[ 3290.970544] ? drain_workqueue+0xa1/0x130
[ 3290.970552] drain_workqueue+0xa1/0x130
[ 3290.970561] destroy_workqueue+0x34/0x1f0
[ 3290.970572] hci_release_dev+0x49/0x180 [bluetooth]
[ 3290.970624] bt_host_release+0x1d/0x30 [bluetooth]
[ 3290.970687] device_release+0x33/0x90
[ 3290.970695] kobject_release+0x63/0x160
[ 3290.970705] dpm_resume+0x164/0x3e0
[ 3290.970710] ? dpm_resume_early+0x251/0x3b0
[ 3290.970718] dpm_resume_end+0xd/0x20
[ 3290.970723] suspend_devices_and_enter+0x1a4/0xba0
[ 3290.970737] pm_suspend+0x26b/0x310
[ 3290.970746] state_store+0x42/0x90
[ 3290.970755] kernfs_fop_write_iter+0x135/0x1b0
[ 3290.970764] new_sync_write+0x125/0x1c0
[ 3290.970777] vfs_write+0x360/0x3c0
[ 3290.970785] ksys_write+0xa7/0xe0
[ 3290.970794] do_syscall_64+0x3a/0x80
[ 3290.970803] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 3290.970811] RIP: 0033:0x7f41b1328164
[ 3290.970819] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 80 00 00 00 00 8b 05 4a d2 2c 00 48 63 ff 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 f3 c3 66 90 55 53 48 89 d5 48 89 f3 48 83
[ 3290.970824] RSP: 002b:00007ffe6ae21b28 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 3290.970831] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007f41b1328164
[ 3290.970836] RDX: 0000000000000004 RSI: 000055965e651070 RDI: 0000000000000004
[ 3290.970839] RBP: 000055965e651070 R08: 000055965e64f390 R09: 00007f41b1e3d1c0
[ 3290.970843] R10: 000000000000000a R11: 0000000000000246 R12: 0000000000000004
[ 3290.970846] R13: 0000000000000001 R14: 000055965e64f2b0 R15: 0000000000000004
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the cpuidle-psci case, runtime PM in combination with the generic PM
domain (genpd), may be used when entering/exiting a shared idlestate. More
precisely, genpd relies on runtime PM to be enabled for the attached device
(in this case it belongs to a CPU), to properly manage the reference
counting of its PM domain.
This works fine most of the time, but during system suspend in
dpm_suspend_late(), the PM core disables runtime PM for all devices. Beyond
this point, calls to pm_runtime_get_sync() to runtime resume a device may
fail and therefore it could also mess up the reference counting in genpd.
To fix this problem, let's call wake_up_all_idle_cpus() in
dpm_suspend_late(), prior to disabling runtime PM. In this way a device
that belongs to a CPU, becomes runtime resumed through cpuidle-psci and
stays like that, because the runtime PM usage count has been bumped in
device_prepare().
Diagnosed-by: Maulik Shah <mkshah@codeaurora.org>
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge updates related to system sleep for 5.16-rc1:
- Clean up hib_wait_io() (Falla Coulibaly).
- Fix sparse warnings in hibernation-related code (Anders Roxell).
- Use vzalloc() and kzalloc() instead of their open-coded
equivalents in hibernation-related code (Cai Huoqing).
- Prevent user space from crashing the kernel by attempting to
restore the system state from a swap partition in use (Ye Bin).
- Do not let "syscore" devices runtime-suspend during system PM
transitions (Rafael Wysocki).
- Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).
- Pause cpuidle later and resume it earlier during system PM
transitions (Rafael Wysocki).
- Make system suspend code use valid_state() consistently (Rafael
Wysocki).
- Add support for enabling wakeup IRQs after invoking the
->runtime_suspend() callback and make two drivers use it (Chunfeng
Yun).
* pm-sleep:
usb: mtu3: enable wake-up interrupt after runtime_suspend called
usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
PM / wakeirq: support enabling wake-up irq after runtime_suspend called
PM: suspend: Use valid_state() consistently
PM: sleep: Pause cpuidle later and resume it earlier during system transitions
PM: suspend: Do not pause cpuidle in the suspend-to-idle path
PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
PM: hibernate: Get block device exclusively in swsusp_check()
PM: hibernate: swap: Use vzalloc() and kzalloc()
PM: hibernate: fix sparse warnings
Revert "PM: sleep: Do not assume that "mem" is always present"
PM: hibernate: Remove blk_status_to_errno in hib_wait_io
PM: sleep: Do not assume that "mem" is always present
|
|
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 8651f97bd951 ("PM / cpuidle: System resume hang fix with
cpuidle") that introduced cpuidle pausing during system suspend
did that to work around a platform firmware issue causing systems
to hang during resume if CPUs were allowed to enter idle states
in the system suspend and resume code paths.
However, pausing cpuidle before the last phase of suspending
devices is the source of an otherwise arbitrary difference between
the suspend-to-idle path and other system suspend variants, so it is
cleaner to do that later, before taking secondary CPUs offline (it
is still safer to take secondary CPUs offline with cpuidle paused,
though).
Modify the code accordingly, but in order to avoid code duplication,
introduce new wrapper functions, pm_sleep_disable_secondary_cpus()
and pm_sleep_enable_secondary_cpus(), to combine cpuidle_pause()
and cpuidle_resume(), respectively, with the handling of secondary
CPUs during system-wide transitions to sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is pointless to pause cpuidle in the suspend-to-idle path,
because it is going to be resumed in the same path later and
pausing it does not serve any particular purpose in that case.
Rework the code to avoid doing that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
transitions
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a1268f ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- The first hunk of a Xen swiotlb fixup series fixing multiple minor
issues and doing some small cleanups
- Some further Xen related fixes avoiding WARN() splats when running as
Xen guests or dom0
- A Kconfig fix allowing the pvcalls frontend to be built as a module
* tag 'for-linus-5.15b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
swiotlb-xen: drop DEFAULT_NSLABS
swiotlb-xen: arrange to have buffer info logged
swiotlb-xen: drop leftover __ref
swiotlb-xen: limit init retries
swiotlb-xen: suppress certain init retries
swiotlb-xen: maintain slab count properly
swiotlb-xen: fix late init retry
swiotlb-xen: avoid double free
xen/pvcalls: backend can be a module
xen: fix usage of pmd_populate in mremap for pv guests
xen: reset legacy rtc flag for PV domU
PM: base: power: don't try to use non-existing RTC for storing data
xen/balloon: use a kernel thread instead a workqueue
|
|
If there is no legacy RTC device, don't try to use it for storing trace
data across suspend/resume.
Cc: <stable@vger.kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20210903084937.19392-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
* pm-cpufreq:
cpufreq: intel_pstate: hybrid: Rework HWP calibration
ACPI: CPPC: Introduce cppc_get_nominal_perf()
* pm-sleep:
PM: sleep: core: Avoid setting power.must_resume to false
PM: sleep: wakeirq: drop useless parameter from dev_pm_attach_wake_irq()
* pm-em:
Documentation: power: include kernel-doc in Energy Model doc
PM: EM: fix kernel-doc comments
|
|
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d461 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This function has the 'irq' parameter which isn't ever used, so drop it.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
|
|
|
|
If CONFIG_PM_OPP=n, of_get_required_opp_performance_state() always
returns -EOPNOTSUPP, and all drivers for devices that are part of a PM
Domain fail to probe with:
failed to set required performance state for power-domain foo: -95
probe of bar failed with error -95
Fix this by treating -EOPNOTSUPP the same as -ENODEV.
Fixes: c016baf7dc58e77a ("PM: domains: Add support for 'required-opps' to set default perf state")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A typical code pattern for pm_clk_create() call is to call it in the
_probe function and to call pm_clk_destroy() both from _probe error path
and from _remove function. For some drivers the whole remove function
would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_clk_create() removes the need for calling pm_clk_destroy() both
in the probe()'s error path and in the remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-3-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
A typical code pattern for pm_runtime_enable() call is to call it in the
_probe function and to call pm_runtime_disable() both from _probe error
path and from _remove function. For some drivers the whole remove
function would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_runtime_enable() removes the need for calling
pm_runtime_disable() both in the probe()'s error path and in the
remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-2-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
GENPD core doesn't support handling performance state changes while
consumer device is runtime-suspended or when runtime PM is disabled.
GENPD core may override performance state that was configured by device
driver while RPM of the device was disabled or device was RPM-suspended.
Let's close that gap by allowing drivers to control performance state
while RPM of a consumer device is disabled and to set up performance
state of RPM-suspended device that will be applied by GENPD core on
RPM-resume of the device.
Fixes: 5937c3ce2122 ("PM: domains: Drop/restore performance state votes for devices at runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some devices within power domains with performance states do not
support DVFS, but still need to vote on a default/static state
while they are active. They can express this using the 'required-opps'
property in device tree, which points to the phandle of the OPP
supported by the corresponding power-domains.
Add support to parse this information from DT and then set the
specified performance state during attach and drop it on detach.
runtime suspend/resume callbacks already have logic to drop/set
the vote as needed and should take care of dropping the default
perf state vote on runtime suspend and restore it back on runtime
resume.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Resolve following checkpatch issue,
Replace symbolic permissions with octal permissions
Signed-off-by: Jinchao Wang <wjc@cdjrlc.com>
Link: https://lore.kernel.org/r/20210626094606.53152-1-wjc@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* pm-cpuidle:
cpuidle: qcom: Add SPM register data for MSM8226
dt-bindings: arm: msm: Add SAW2 for MSM8226
* pm-sleep:
PM: sleep: Use ktime_us_delta() in initcall_debug_report()
* pm-domains:
PM: domains: Shrink locking area of the gpd_list_lock
|
|
On trogdor devices I see the following lockdep splat when stopping
youtube with lockdep enabled in the kernel.
======================================================
WARNING: possible circular locking dependency detected
5.13.0-rc2 #71 Not tainted
------------------------------------------------------
ThreadPoolSingl/3969 is trying to acquire lock:
ffffff80d4d5c080 (&inst->lock#3){+.+.}-{3:3}, at: vdec_buf_cleanup+0x3c/0x17c [venus_dec]
but task is already holding lock:
ffffff80d3c3c4f8 (&q->mmap_lock){+.+.}-{3:3}, at: vb2_core_reqbufs+0xe4/0x390 [videobuf2_common]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #5 (&q->mmap_lock){+.+.}-{3:3}:
__mutex_lock_common+0xcc/0xb88
mutex_lock_nested+0x5c/0x68
vb2_mmap+0xf4/0x290 [videobuf2_common]
v4l2_m2m_fop_mmap+0x44/0x50 [v4l2_mem2mem]
v4l2_mmap+0x5c/0xa4
mmap_region+0x310/0x5a4
do_mmap+0x348/0x43c
vm_mmap_pgoff+0xfc/0x178
ksys_mmap_pgoff+0x84/0xfc
__arm64_compat_sys_aarch32_mmap2+0x2c/0x38
invoke_syscall+0x54/0x110
el0_svc_common+0x88/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
-> #4 (&mm->mmap_lock){++++}-{3:3}:
__might_fault+0x60/0x88
filldir64+0x124/0x3a0
dcache_readdir+0x7c/0x1ec
iterate_dir+0xc4/0x184
__arm64_sys_getdents64+0x78/0x170
invoke_syscall+0x54/0x110
el0_svc_common+0xa8/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
-> #3 (&sb->s_type->i_mutex_key#3){++++}-{3:3}:
down_write+0x94/0x1f4
start_creating+0xb0/0x174
debugfs_create_dir+0x28/0x138
opp_debug_register+0x88/0xc0
_add_opp_dev+0x84/0x9c
_add_opp_table_indexed+0x16c/0x310
_of_add_table_indexed+0x70/0xb5c
dev_pm_opp_of_add_table_indexed+0x20/0x2c
of_genpd_add_provider_onecell+0xc4/0x1c8
rpmhpd_probe+0x21c/0x278
platform_probe+0xb4/0xd4
really_probe+0x140/0x35c
driver_probe_device+0x90/0xcc
__device_attach_driver+0xa4/0xc0
bus_for_each_drv+0x8c/0xd8
__device_attach+0xc4/0x150
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
device_add+0x22c/0x3fc
of_device_add+0x44/0x54
of_platform_device_create_pdata+0xb0/0xf4
of_platform_bus_create+0x1d0/0x350
of_platform_populate+0x80/0xd4
devm_of_platform_populate+0x64/0xb0
rpmh_rsc_probe+0x378/0x3dc
platform_probe+0xb4/0xd4
really_probe+0x140/0x35c
driver_probe_device+0x90/0xcc
__device_attach_driver+0xa4/0xc0
bus_for_each_drv+0x8c/0xd8
__device_attach+0xc4/0x150
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
device_add+0x22c/0x3fc
of_device_add+0x44/0x54
of_platform_device_create_pdata+0xb0/0xf4
of_platform_bus_create+0x1d0/0x350
of_platform_bus_create+0x21c/0x350
of_platform_populate+0x80/0xd4
of_platform_default_populate_init+0xb8/0xd4
do_one_initcall+0x1b4/0x400
do_initcall_level+0xa8/0xc8
do_initcalls+0x5c/0x9c
do_basic_setup+0x2c/0x38
kernel_init_freeable+0x1a4/0x1ec
kernel_init+0x20/0x118
ret_from_fork+0x10/0x30
-> #2 (gpd_list_lock){+.+.}-{3:3}:
__mutex_lock_common+0xcc/0xb88
mutex_lock_nested+0x5c/0x68
__genpd_dev_pm_attach+0x70/0x18c
genpd_dev_pm_attach_by_id+0xe4/0x158
genpd_dev_pm_attach_by_name+0x48/0x60
dev_pm_domain_attach_by_name+0x2c/0x38
dev_pm_opp_attach_genpd+0xac/0x160
vcodec_domains_get+0x94/0x14c [venus_core]
core_get_v4+0x150/0x188 [venus_core]
venus_probe+0x138/0x444 [venus_core]
platform_probe+0xb4/0xd4
really_probe+0x140/0x35c
driver_probe_device+0x90/0xcc
device_driver_attach+0x58/0x7c
__driver_attach+0xc8/0xe0
bus_for_each_dev+0x88/0xd4
driver_attach+0x30/0x3c
bus_add_driver+0x10c/0x1e0
driver_register+0x70/0x108
__platform_driver_register+0x30/0x3c
0xffffffde113e1044
do_one_initcall+0x1b4/0x400
do_init_module+0x64/0x1fc
load_module+0x17f4/0x1958
__arm64_sys_finit_module+0xb4/0xf0
invoke_syscall+0x54/0x110
el0_svc_common+0x88/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
-> #1 (&opp_table->genpd_virt_dev_lock){+.+.}-{3:3}:
__mutex_lock_common+0xcc/0xb88
mutex_lock_nested+0x5c/0x68
_set_required_opps+0x74/0x120
_set_opp+0x94/0x37c
dev_pm_opp_set_rate+0xa0/0x194
core_clks_set_rate+0x28/0x58 [venus_core]
load_scale_v4+0x228/0x2b4 [venus_core]
session_process_buf+0x160/0x198 [venus_core]
venus_helper_vb2_buf_queue+0xcc/0x130 [venus_core]
vdec_vb2_buf_queue+0xc4/0x140 [venus_dec]
__enqueue_in_driver+0x164/0x188 [videobuf2_common]
vb2_core_qbuf+0x13c/0x47c [videobuf2_common]
vb2_qbuf+0x88/0xec [videobuf2_v4l2]
v4l2_m2m_qbuf+0x84/0x15c [v4l2_mem2mem]
v4l2_m2m_ioctl_qbuf+0x24/0x30 [v4l2_mem2mem]
v4l_qbuf+0x54/0x68
__video_do_ioctl+0x2bc/0x3bc
video_usercopy+0x558/0xb04
video_ioctl2+0x24/0x30
v4l2_ioctl+0x58/0x68
v4l2_compat_ioctl32+0x84/0xa0
__arm64_compat_sys_ioctl+0x12c/0x140
invoke_syscall+0x54/0x110
el0_svc_common+0x88/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
-> #0 (&inst->lock#3){+.+.}-{3:3}:
__lock_acquire+0x248c/0x2d6c
lock_acquire+0x240/0x314
__mutex_lock_common+0xcc/0xb88
mutex_lock_nested+0x5c/0x68
vdec_buf_cleanup+0x3c/0x17c [venus_dec]
__vb2_queue_free+0x98/0x204 [videobuf2_common]
vb2_core_reqbufs+0x14c/0x390 [videobuf2_common]
vb2_reqbufs+0x58/0x74 [videobuf2_v4l2]
v4l2_m2m_reqbufs+0x58/0x90 [v4l2_mem2mem]
v4l2_m2m_ioctl_reqbufs+0x24/0x30 [v4l2_mem2mem]
v4l_reqbufs+0x58/0x6c
__video_do_ioctl+0x2bc/0x3bc
video_usercopy+0x558/0xb04
video_ioctl2+0x24/0x30
v4l2_ioctl+0x58/0x68
v4l2_compat_ioctl32+0x84/0xa0
__arm64_compat_sys_ioctl+0x12c/0x140
invoke_syscall+0x54/0x110
el0_svc_common+0x88/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
other info that might help us debug this:
Chain exists of:
&inst->lock#3 --> &mm->mmap_lock --> &q->mmap_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&q->mmap_lock);
lock(&mm->mmap_lock);
lock(&q->mmap_lock);
lock(&inst->lock#3);
*** DEADLOCK ***
1 lock held by ThreadPoolSingl/3969:
#0: ffffff80d3c3c4f8 (&q->mmap_lock){+.+.}-{3:3}, at: vb2_core_reqbufs+0xe4/0x390 [videobuf2_common]
stack backtrace:
CPU: 2 PID: 3969 Comm: ThreadPoolSingl Not tainted 5.13.0-rc2 #71
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Call trace:
dump_backtrace+0x0/0x1b4
show_stack+0x24/0x30
dump_stack+0xe0/0x15c
print_circular_bug+0x32c/0x388
check_noncircular+0x138/0x140
__lock_acquire+0x248c/0x2d6c
lock_acquire+0x240/0x314
__mutex_lock_common+0xcc/0xb88
mutex_lock_nested+0x5c/0x68
vdec_buf_cleanup+0x3c/0x17c [venus_dec]
__vb2_queue_free+0x98/0x204 [videobuf2_common]
vb2_core_reqbufs+0x14c/0x390 [videobuf2_common]
vb2_reqbufs+0x58/0x74 [videobuf2_v4l2]
v4l2_m2m_reqbufs+0x58/0x90 [v4l2_mem2mem]
v4l2_m2m_ioctl_reqbufs+0x24/0x30 [v4l2_mem2mem]
v4l_reqbufs+0x58/0x6c
__video_do_ioctl+0x2bc/0x3bc
video_usercopy+0x558/0xb04
video_ioctl2+0x24/0x30
v4l2_ioctl+0x58/0x68
v4l2_compat_ioctl32+0x84/0xa0
__arm64_compat_sys_ioctl+0x12c/0x140
invoke_syscall+0x54/0x110
el0_svc_common+0x88/0xf0
do_el0_svc_compat+0x28/0x34
el0_svc_compat+0x24/0x34
el0_sync_compat_handler+0xc0/0xf0
el0_sync_compat+0x19c/0x1c0
The 'gpd_list_lock' is nominally named as such to protect the 'gpd_list'
from concurrent access and mutation. Unfortunately, holding that mutex
around various OPP framework calls leads to lockdep splats because now
we're doing various operations in OPP core such as registering with
debugfs while holding the list lock. We don't need to hold any list
mutex while we're calling into OPP, so let's shrink the locking area of
the 'gpd_list_lock' so that lockdep isn't triggered. This also helps
reduce contention on this lock, which probably doesn't matter much but
at least is nice to have.
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-pm@vger.kernel.org>
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use ktime_us_delta() to make the debug log more precise instead of
shifting the return value of ktime_to_ns() applied to a ktime_sub()
result by 10 bit positions to the right.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
[ rjw: Changelog rewrite, subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-domains:
PM: domains: Drop/restore performance state votes for devices at runtime PM
PM: domains: Return early if perf state is already set for the device
PM: domains: Split code in dev_pm_genpd_set_performance_state()
PM: domains: fix some kernel-doc issues
* pm-devfreq:
PM / devfreq: passive: Fix get_target_freq when not using required-opp
dt-bindings: devfreq: tegra30-actmon: Add cooling-cells
dt-bindings: devfreq: tegra30-actmon: Convert to schema
PM / devfreq: userspace: Use DEVICE_ATTR_RW macro
PM / devfreq: imx8m-ddrc: Remove DEVFREQ_GOV_SIMPLE_ONDEMAND dependency
PM / devfreq: tegra30: Support thermal cooling
PM / devfreq: imx-bus: Remove imx_bus_get_dev_status
PM / devfreq: Add missing error code in devfreq_add_device()
|
|
* pm-core:
PM: runtime: Clarify documentation when callbacks are unassigned
PM: runtime: Allow unassigned ->runtime_suspend|resume callbacks
PM: runtime: Improve path in rpm_idle() when no callback
PM: runtime: document common mistake with pm_runtime_get_sync()
* pm-sleep:
PM: hibernate: remove leading spaces before tabs
PM: sleep: remove trailing spaces and tabs
PM: hibernate: fix spelling mistakes
PM: wakeirq: Set IRQF_NO_AUTOEN when requesting the IRQ
|
|
We are currently allowing ->runtime_idle() callbacks to be unassigned
without returning an error code from rpm_idle(). This has been useful to
avoid boilerplate code in drivers. Let's take this approach a step further,
by allowing also unassigned ->runtime_suspend|resume() callbacks.
In this way, a consumer/supplier device link can be used to let a consumer
device be power managed through its supplier device, without requiring
assigned ->runtime_suspend|resume() callbacks for the consumer device, for
example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When pm_runtime_no_callbacks() has been called for a struct device to set
the dev->power.no_callbacks flag for it, it enables rpm_idle() to take a
slightly quicker path by assuming that a ->runtime_idle() callback would
have returned 0 to indicate success.
A device that does not have the dev->power.no_callbacks flag set for it,
may still be missing a corresponding ->runtime_idle() callback, in which
case the slower path in rpm_idle() is taken. Let's improve the behaviour
for this case, by aligning code to the quicker path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A subsystem/driver that need to manage OPPs for its device, should
typically drop its vote for the OPP when the device becomes runtime
suspended. In this way, the corresponding aggregation of the performance
state votes that is managed in genpd for the attached PM domain, may find
that the aggregated vote can be decreased. Hence, it may allow genpd to set
the lower performance state for the PM domain, thus avoiding to waste
energy.
To accomplish this, typically a subsystem/driver would need to call
dev_pm_opp_set_rate|opp() for its device from its ->runtime_suspend()
callback, to drop the vote for the OPP. Accordingly, it needs another call
to dev_pm_opp_set_rate|opp() to restore the vote for the OPP from its
->runtime_resume() callback.
To avoid boilerplate code in subsystems/driver to deal with these things,
let's instead manage this internally in genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When dev_pm_genpd_set_performance_state() gets called to set a new
performance state for the device, let's take a quicker path by doing an
early return, if it turns out that the new state is already set for the
device.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To prepare some of the code in dev_pm_genpd_set_performance_state() to be
re-used from subsequent changes, let's split it up into two functions.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix the following make W=1 kernel build warnings:
drivers/base/power/domain_governor.c:259: warning: Function parameter or member 'now' not described in '_default_power_down_ok'
drivers/base/power/domain.c:581: warning: Function parameter or member 'depth' not described in 'genpd_power_off'
drivers/base/power/domain.c:2520: warning: Function parameter or member 'np' not described in 'of_genpd_remove_last'
drivers/base/power/domain.c:2520: warning: Excess function parameter 'provider' description in 'of_genpd_remove_last'
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
request_irq() after setting IRQ_NOAUTOEN as below
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
can be replaced by request_irq() with IRQF_NO_AUTOEN flag.
This change is just to simplify the code, no actual functional
changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As pm_runtime_need_not_resume() relies also on usage_count, it can return
a different value in pm_runtime_force_suspend() compared to when called in
pm_runtime_force_resume(). Different return values can happen if anything
calls PM runtime functions in between, and causes the parent child_count
to increase on every resume.
So far I've seen the issue only for omapdrm that does complicated things
with PM runtime calls during system suspend for legacy reasons:
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
pm_runtime_force_suspend() for 58000000.dss, !pm_runtime_need_not_resume()
__update_runtime_status()
system suspended
pm_runtime_force_resume() for 58000000.dss, pm_runtime_need_not_resume()
pm_runtime_enable() only called because of pm_runtime_need_not_resume()
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
...
rpm_suspend for 58000000.dss but parent child_count is now unbalanced
Let's fix the issue by adding a flag for needs_force_resume and use it in
pm_runtime_force_resume() instead of pm_runtime_need_not_resume().
Additionally omapdrm system suspend could be simplified later on to avoid
lots of unnecessary PM runtime calls and the complexity it adds. The
driver can just use internal functions that are shared between the PM
runtime and system suspend related functions.
Fixes: 4918e1f87c5f ("PM / runtime: Rework pm_runtime_force_suspend/resume()")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-docs:
PM: clk: remove kernel-doc warning
PM: wakeup: fix kernel-doc warnings and fix typos
PM: runtime: remove kernel-doc warnings
* pm-tools:
pm-graph: Fix typo "accesible"
|
|
* pm-core:
PM: runtime: Add documentation for pm_runtime_resume_and_get()
PM: runtime: Replace inline function pm_runtime_callbacks_present()
PM: core: Remove duplicate declaration from header file
* pm-pci:
PCI: PM: Do not read power state in pci_enable_device_flags()
* pm-sleep:
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
PM: wakeup: use dev_set_name() directly
PM: sleep: fix typos in comments
freezer: Remove unused inline function try_to_freeze_nowarn()
* pm-domains:
PM: domains: Don't runtime resume devices at genpd_prepare()
* powercap:
powercap: RAPL: Fix struct declaration in header file
MAINTAINERS: Add DTPM subsystem maintainer
powercap: Add Hygon Fam18h RAPL support
|
|
The variable retval is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have open coded dev_set_name() implementation, replace that
with a direct call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove make W=1 warning:
drivers/base/power/clock_ops.c:148: warning: expecting prototype for
pm_clk_enable(). Prototype was for __pm_clk_enable() instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove make W=1 warnings and fit 'Itereates' typos
drivers/base/power/wakeup.c:403: warning: wrong kernel-doc identifier on line:
* device_wakeup_arm_wake_irqs(void)
drivers/base/power/wakeup.c:419: warning: wrong kernel-doc identifier on line:
* device_wakeup_disarm_wake_irqs(void)
drivers/base/power/wakeup.c:537: warning: Function parameter or member
'enable' not described in 'device_set_wakeup_enable'
drivers/base/power/wakeup.c:592: warning: expecting prototype for
wakup_source_activate(). Prototype was for wakeup_source_activate()
instead
drivers/base/power/wakeup.c:697: warning: expecting prototype for
wakup_source_deactivate(). Prototype was for
wakeup_source_deactivate() instead
drivers/base/power/wakeup.c:795: warning: Function parameter or member
't' not described in 'pm_wakeup_timer_fn'
drivers/base/power/wakeup.c:795: warning: Excess function parameter
'data' description in 'pm_wakeup_timer_fn'
drivers/base/power/wakeup.c:1027: warning: Function parameter or
member 'set' not described in 'pm_wakep_autosleep_enabled'
drivers/base/power/wakeup.c:1027: warning: Excess function parameter
'enabled' description in 'pm_wakep_autosleep_enabled'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
remove make W=1 warnings
drivers/base/power/runtime.c:926: warning: Function parameter or
member 'timer' not described in 'pm_suspend_timer_fn'
drivers/base/power/runtime.c:926: warning: Excess function parameter
'data' description in 'pm_suspend_timer_fn'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pm_runtime_put_suppliers() must not decrement rpm_active unless the
consumer is suspended. That is because, otherwise, it could suspend
suppliers for an active consumer.
That can happen as follows:
static int driver_probe_device(struct device_driver *drv, struct device *dev)
{
int ret = 0;
if (!device_is_registered(dev))
return -ENODEV;
dev->can_match = true;
pr_debug("bus: '%s': %s: matched device %s with driver %s\n",
drv->bus->name, __func__, dev_name(dev), drv->name);
pm_runtime_get_suppliers(dev);
if (dev->parent)
pm_runtime_get_sync(dev->parent);
At this point, dev can runtime suspend so rpm_put_suppliers() can run,
rpm_active becomes 1 (the lowest value).
pm_runtime_barrier(dev);
if (initcall_debug)
ret = really_probe_debug(dev, drv);
else
ret = really_probe(dev, drv);
Probe callback can have runtime resumed dev, and then runtime put
so dev is awaiting autosuspend, but rpm_active is 2.
pm_request_idle(dev);
if (dev->parent)
pm_runtime_put(dev->parent);
pm_runtime_put_suppliers(dev);
Now pm_runtime_put_suppliers() will put the supplier
i.e. rpm_active 2 -> 1, but consumer can still be active.
return ret;
}
Fix by checking the runtime status. For any status other than
RPM_SUSPENDED, rpm_active can be considered to be "owned" by
rpm_[get/put]_suppliers() and pm_runtime_put_suppliers() need do nothing.
Reported-by: Asutosh Das <asutoshd@codeaurora.org>
Fixes: 4c06c4e6cf63 ("driver core: Fix possible supplier PM-usage counter imbalance")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|