| Age | Commit message (Collapse) | Author |
|---|
|
As the possible failure of the allocation, kzalloc() may return NULL
pointer.
Therefore, it should be better to check the 'sgi' in order to prevent
the dereference of NULL pointer.
Fixes: 23ae3a7877718 ("net: dsa: felix: add stream gate settings for psfp").
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220329090800.130106-1-zhengyongjun3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel test robot reported build warnings with a randconfig that
built realtek-{smi,mdio} without CONFIG_OF set. Since both interface
drivers are using OF and will not probe without, add the corresponding
dependency to Kconfig.
Link: https://lore.kernel.org/all/202203231233.Xx73Y40o-lkp@intel.com/
Link: https://lore.kernel.org/all/202203231439.ycl0jg50-lkp@intel.com/
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers")
Fixes: 765c39a4fafe ("net: dsa: realtek: convert subdrivers into modules")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20220323124225.91763-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix switch has 6 ports, 2 of which are internal.
Due to some misunderstanding, my initial suggestion for
vsc9959_port_modes[]:
https://patchwork.kernel.org/project/netdevbpf/patch/20220129220221.2823127-10-colin.foster@in-advantage.com/#24718277
got translated by Colin into a 5-port array, leading to an all-zero port
mode mask for port 5.
Fixes: acf242fc739e ("net: dsa: felix: remove prevalidate_phy_mode interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220318195812.276276-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36b3 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Gain support for port mirroring using tc-matchall by forwarding the
calls to the ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to erratum described in DS80000687C[1]: "Module 2: Link drops with
some EEE link partners.", we need to "Disable the EEE next page
exchange in EEE Global Register 2"
1 - https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220316125529.1489045-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables non-standard MTUs on a per-port basis, with the overall
frame size set based on the CPU port.
When the MTU is not changed, this should have no effect.
Long packets crash the switch with MTUs of greater than 2526, so the
maximum is limited for now. Medium packets are sometimes dropped (e.g.
TCP over 2477, UDP over 2516-2519, ICMP over 2526), Hence an MTU value
of 2400 seems safe.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20220308230457.1599237-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net/dsa/dsa2.c
commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails")
commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master")
https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/
drivers/net/ethernet/intel/ice/ice.h
commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU")
commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device")
https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/
drivers/staging/gdm724x/gdm_lte.c
commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()")
commit 4bcc4249b4cf ("staging: Use netif_rx().")
https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two blamed commits were written/tested individually but not
together.
When put together, commit 90897569beb1 ("net: dsa: felix: start off with
flooding disabled on the CPU port"), which deletes a reinitialization of
PGID_UC/PGID_MC/PGID_BC, is no longer sufficient to ensure that these
port masks don't contain the CPU port module.
This is because commit b903a6bd2e19 ("net: dsa: felix: migrate flood
settings from NPI to tag_8021q CPU port") overwrites the hardware
default settings towards the CPU port module with the settings that used
to be present on the NPI port treated as a regular port. There, flooding
is enabled, so flooding would get enabled on the CPU port module too.
Adding conditional logic somewhere within felix_setup_tag_npi() to
configure either the default no-flood policy or the flood policy
inherited from the tag_8021q CPU port from a previous call to
dsa_port_manage_cpu_flood() is getting complicated. So just let the
migration logic do its thing during initial setup (which will
temporarily turn on flooding), then turn flooding off for the NPI port
after felix_set_tag_protocol() finishes. Here we are in felix_setup(),
so the DSA slave interfaces are not yet created, and this doesn't affect
traffic in any way.
Fixes: 90897569beb1 ("net: dsa: felix: start off with flooding disabled on the CPU port")
Fixes: b903a6bd2e19 ("net: dsa: felix: migrate flood settings from NPI to tag_8021q CPU port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer need the workaround in the felix driver to avoid calling
dsa_port_walk_fdbs() when &dp->fdbs is an uninitialized list, because
that list is now initialized from all call paths of felix_set_tag_protocol().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an apparently incorrect conflict resolution on my part in commit
54c319846086 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet extraction failures over register-based MMIO are silent, and
difficult to pinpoint. Add an error message to remedy this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Automated tools complain that felix_check_xtr_pkt() has logic to drain
the CPU queue on the reception of a PTP packet over Ethernet, yet it
returns an uninitialized error code in the case where the CPU queue was
empty.
This is not likely to happen (/possible if hardware works correctly),
but it isn't a fatal condition either. The PTP packet will be dequeued
from the CPU queue when the next PTP packet arrives. So initialize "err"
to 0 for the case where nothing was dequeued during this iteration.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA ->port_rxtstamp() function is never called for PTP_CLASS_NONE:
dsa_skb_defer_rx_timestamp:
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
So practically, the argument is unused, so remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This assignment is redundant, since ocelot->npi has already been set to
-1 by felix_npi_port_deinit(). Call path:
felix_change_tag_protocol
-> felix_del_tag_protocol(DSA_TAG_PROTO_OCELOT)
-> felix_teardown_tag_npi
-> felix_npi_port_deinit
-> felix_set_tag_protocol(DSA_TAG_PROTO_OCELOT_8021Q)
-> felix_setup_tag_8021q
-> felix_8021q_cpu_port_init
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
felix_migrate_flood_to_tag_8021q_port() takes care of clearing the
flooding bits on the old CPU port (which was the CPU port module), so
manually clearing this bit from PGID_UC, PGID_MC, PGID_BC is redundant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver probes with all ports as standalone, and it supports unicast
filtering. So DSA will call port_fdb_add() for all necessary addresses
on the current CPU port. We also handle migrations when the CPU port
hardware resource changes (on tagging protocol change), so there should
not be any unknown address that we have to receive while not promiscuous.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the tagging protocol changes from "ocelot" to "ocelot-8021q" or in
reverse, the DSA promiscuity setting that was applied for the old CPU
port must be transferred to the new one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for direct RMII MAC mode. This allows hardware with CPU port
connected in direct 100M fixed link to work properly.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/a962d1ccbeec42daa10dd8aff0e66e31f0faf1eb.1646050203.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the given cmode has no serdes, mv88e6xxx_serdes_get_lane() returns
-NODEV. Earlier in the same function the code skips serdes handing in
this case. Do the same after cmode set.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/cd95cf3422ae8daf297a01fa9ec3931b203cdf45.1646050203.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All users of the felix driver were creating their own prevalidate_phy_mode
function. The same logic can be performed in a more general way by using a
simple array of bit fields.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For sja1105, to enforce FDB isolation simply means to turn on
Independent VLAN Learning unconditionally, and to remap VLAN-unaware FDB
and MDB entries towards the private VLAN allocated by tag_8021q for each
bridge.
Standalone ports each have their own standalone tag_8021q VLAN. No
learning happens in that VLAN due to:
- learning being disabled on standalone user ports
- learning being disabled on the CPU port (we use
assisted_learning_on_cpu_port which only installs bridge FDBs)
VLAN-aware ports learn FDB entries with the bridge VLANs.
VLAN-unaware bridge ports learn with the tag_8021q VLAN for bridging.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_8021q_bridge_tx_fwd_offload_vid is no longer used just for
bridge TX forwarding offload, it is the private VLAN reserved for
VLAN-unaware bridging in a way that is compatible with FDB isolation.
So just rename it dsa_tag_8021q_bridge_vid.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the old Shared VLAN Learning mode of operation that tag_8021q
previously used for forwarding, we needed to have distinct concepts for
an RX and a TX VLAN.
An RX VLAN could be installed on all ports that were members of a given
bridge, so that autonomous forwarding could still work, while a TX VLAN
was dedicated for precise packet steering, so it just contained the CPU
port and one egress port.
Now that tag_8021q uses Independent VLAN Learning and imprecise RX/TX
all over, those lines have been blurred and we no longer have the need
to do precise TX towards a port that is in a bridge. As for standalone
ports, it is fine to use the same VLAN ID for both RX and TX.
This patch changes the tag_8021q format by shifting the VLAN range it
reserves, and halving it. Previously, our DIR bits were encoding the
VLAN direction (RX/TX) and were set to either 1 or 2. This meant that
tag_8021q reserved 2K VLANs, or 50% of the available range.
Change the DIR bits to a hardcoded value of 3 now, which makes tag_8021q
reserve only 1K VLANs, and a different range now (the last 1K). This is
done so that we leave the old format in place in case we need to return
to it.
In terms of code, the vid_is_dsa_8021q_rxvlan and vid_is_dsa_8021q_txvlan
functions go away. Any vid_is_dsa_8021q is both a TX and an RX VLAN, and
they are no longer distinct. For example, felix which did different
things for different VLAN types, now needs to handle the RX and the TX
logic for the same VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix driver, which also has a tagging protocol implementation based
on tag_8021q, does not care about adding the RX VLAN that is pvid on one
port on the other ports that are in the same bridge with it. It simply
doesn't need that, because in its implementation, the RX VLAN that is
pvid of a port is only used to install a TCAM rule that pushes that VLAN
ID towards the CPU port.
Now that tag_8021q no longer performs Shared VLAN Learning based
forwarding, the RX VLANs are actually segregated into two types:
standalone VLANs and VLAN-unaware bridging VLANs. Since you actually
have to call dsa_tag_8021q_bridge_join() to get a bridging VLAN from
tag_8021q, and felix does not do that because it doesn't need it, it
means that it only gets standalone port VLANs from tag_8021q. Which is
perfect because this means it can drop its workarounds that avoid the
VLANs it does not need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot DSA driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs, and removes the need to set the PCS
in the mac_config() callback, delving into the higher DSA levels to do
so.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the supported interfaces bitmap is populated, phylink will itself
check that the interface mode is present in this bitmap. Drivers no
longer need to perform this check themselves. Remove these checks.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
