| Age | Commit message (Collapse) | Author |
|---|
|
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DT provides rs485-term, set termination flag as supported.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 31f6bd7fad3b ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.
Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to be add new flags more cleanly and safely, return -EINVAL
from TIOCSRS485 ioctl for the flags bits which are not among the
current legacy ones.
This might cause a regression for userspace as those non-flag bits do
not currently trigger -EINVAL. However, it would only occur if the
userspace is sending garbage bits so perhaps we'll get away with this
change.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-25-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When SER_RS485_ENABLED is not set, having any other flag/field set in
serial_rs485 struct does not have an effect different from not having
them set. Thus, make the serial_rs485 struct also match the behavior
for all flags, not just SER_RS485_ENABLED.
Some drivers do similar clearing of rs485 struct in their
rs485_config() already, but not all. This change makes the behavior
consistent across drivers.
Don't try to validate rs485 struct further when no RS485 is requested,
this silences some bogus warnings.
This change has (minor) userspace visible impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-24-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sanitize serial_rs485 struct before calling into rs485_setup. The
drivers provide supported_rs485 to help sanitization of the fields.
If neither of SER_RS485_RTS_ON_SEND or SER_RS485_RTS_AFTER_SEND
supported, don't pretend they can be set to sane settings but clear
them both instead. If only one of them is supported it may look
tempting to use the one driver supports to set the other, however, the
userspace does not have that information readily available so it
wouldn't be helpful.
While adjusting the documentation, remove also the claim that
TIOCGRS485 would call driver specific code. In reality, it does nothing
else than copies the stored serial_rs485 structure from uart_port to
userspace.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add uart_sanitize_serial_rs485() function for sanitizing serial_rs485
structure fields.
No functional changes.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.
In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if this callback implementation is present.
In suspend sequence there is a need to perform stop_rx during suspend
sequence to prevent any asynchronous data over rx line. However this
can cause problem to drivers which dont do re-start_rx during set_termios.
Add new callback start_rx and perform stop_rx only when implementation of
start_rx is present. Also add call to start_rx in resume sequence so that
drivers who come across this problem can make use of this framework.
Fixes: c9d2325cdb92 ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1654627965-1461-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
disabled
For the case of console_suspend disabled, if back to back suspend/resume
test is executed, at the end of test, sometimes console would appear to
be frozen not responding to input. This would happen because, during
resume, rx transactions can come in before system is ready, malfunction
of rx happens in turn resulting in console appearing to be stuck.
Do a stop_rx in suspend sequence to prevent this.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1652692810-31148-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Struct uart_port currently stores FIFO timeout. Having character timing
information readily available is useful. Even serial core itself
determines char_time from port->timeout using inverse calculation.
Store frame_time directly into uart_port. Character time is stored in
nanoseconds to have reasonable precision with high rates. To avoid
overflow, 64-bit math is necessary.
It might be possible to determine timeout from frame_time by
multiplying it with fifosize as needed but only part of the users seem
to be protected by a lock. Thus, this patch does not pursue storing
only frame_time in uart_port.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not set timeout to twice the approximate amount of time to send the
entire FIFO if CTS is enabled. If the caller requested no timeout, e.g.
when userspace program called tcdrain(), then wait without any timeout.
Premature return from tcdrain() was observed on imx based system which
has 32 character long transmitter FIFO with hardware CTS handling.
Simple userspace application that reproduces problem has to:
* Open tty device, enable hardware flow control (CRTSCTS)
* Write data, e.g. 26 bytes
* Call tcdrain() to wait for the transmitter
* Close tty device
The other side of serial connection has to:
* Receive some data, e.g. 10 bytes
* Set RTS output (CTS input from sender perspective) inactive for
at least twice the port timeout
* Try to receive remaining data
Without this patch, userspace application will finish without any error
while the other side of connection will never receive remaining data.
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220228054911.1420221-1-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When flow control is enabled, the UART should set RTS to false
during suspend to stop incoming data. Currently, the suspend
routine sets the mctrl register in the uart to zero, but leaves
the shadow version in the uart_port struct alone so that resume
can restore it. This causes a problem later in suspend when
serial8250_do_shutdown() is called which uses the shadow mctrl
register to clear some additional bits but ends up restoring RTS.
The solution is to clear RTS from the shadow version before
serial8250_do_shutdown() is called and restore it after.
Signed-off-by: Al Cooper <alcooperx@comcast.net>
Link: https://lore.kernel.org/r/20220324145620.41573-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Several drivers that support setting the RS485 configuration via userspace
implement one or more of the following tasks:
- in case of an invalid RTS configuration (both RTS after send and RTS on
send set or both unset) fall back to enable RTS on send and disable RTS
after send
- nullify the padding field of the returned serial_rs485 struct
- copy the configuration into the uart port struct
- limit RTS delays to 100 ms
Move these tasks into the serial core to make them generic and to provide
a consistent behaviour among all drivers.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f165f (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The free_page(addr), which becomes free_pages(addr, 0) checks addr
against 0. No need to repeat this check in the callers.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220204152808.10808-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some EXPORT_SYMBOLs are grouped at one location. Some follow functions
they export, but a newline is present before them. Fix all these and
move them where they belong.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
RTS polarity of rs485-enabled ports is currently initialized on uart
open via:
tty_port_open()
tty_port_block_til_ready()
tty_port_raise_dtr_rts() # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts()
There's at least three problems here:
First, if no baud rate is set, RTS polarity is not initialized.
That's the right thing to do for rs232, but not for rs485, which
requires that RTS is deasserted unconditionally.
Second, if the DeviceTree property "linux,rs485-enabled-at-boot-time" is
present, RTS should be deasserted as early as possible, i.e. on probe.
Otherwise it may remain asserted until first open.
Third, even though RTS is deasserted on open and close, it may
subsequently be asserted by uart_throttle(), uart_unthrottle() or
uart_set_termios() because those functions aren't rs485-aware.
(Only uart_tiocmset() is.)
To address these issues, move RTS initialization from uart_port_dtr_rts()
to uart_configure_port(). Prevent subsequent modification of RTS
polarity by moving the existing rs485 check from uart_tiocmget() to
uart_update_mctrl().
That way, RTS is initialized on probe and then remains unmodified unless
the uart transmits data. If rs485 is enabled at runtime (instead of at
boot) through a TIOCSRS485 ioctl(), RTS is initialized by the uart
driver's ->rs485_config() callback and then likewise remains unmodified.
The PL011 driver initializes RTS on uart open and prevents subsequent
modification in its ->set_mctrl() callback. That code is obsoleted by
the present commit, so drop it.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2d2acaf3a69e89b7bf687c912022b11fd29dfa1e.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a6845e1e1b78 ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b78 ("serial: core: Consider rs485 settings to drive RTS")
Cc: stable@vger.kernel.org # v4.14+
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit f45709df7731 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df7731 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are two consequent checks of uport != NULL in
uart_port_shutdown(). Join these two under a single block.
De-multiline the comments when shuffling with them anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68ed9 (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Report extra baud rates supported above the base rate for ports with the
UPF_MAGIC_MULTIPLIER property, so that people have a way to find out
that they can be used with their system, e.g.:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
serial8250.0: ttyS0 extra baud rates supported: 230400, 460800
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS1 extra baud rates supported: 230400, 460800
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Otherwise there is no clear way to figure this out, as the feature is
only reported as an obscure TTY flag in bit 16:
$ cat /sys/class/tty/ttyS[0-2]/flags
0x10010040
0x10010040
0x90000040
$
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260334170.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* make parameters const (as they are only read)
* return bool (as comparison results are returned)
* add \n before final return
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from drivers that got this wrong.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519092541.10137-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit that added this check did so in a very strange way - first
security_locked_down() is called, its value stored into retval, and if
it's nonzero, then an additional check is made for (change_irq ||
change_port), and if this is true, the function returns. However, if
the goto exit branch is not taken, the code keeps the retval value and
continues executing the function. Then, depending on whether
uport->ops->verify_port is set, the retval value may or may not be reset
to zero and eventually the error value from security_locked_down() may
abort the function a few lines below.
I will go out on a limb and assume that this isn't the intended behavior
and that an error value from security_locked_down() was supposed to
abort the function only in case (change_irq || change_port) is true.
Note that security_locked_down() should be called last in any series of
checks, since the SELinux implementation of this hook will do a check
against the policy and generate an audit record in case of denial. If
the operation was to carry on after calling security_locked_down(), then
the SELinux denial record would be bogus.
See commit 59438b46471a ("security,lockdown,selinux: implement SELinux
lockdown") for how SELinux implements this hook.
Fixes: 794edf30ee6c ("lockdown: Lock down TIOCSSERIAL")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210507115719.140799-1-omosnace@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
Fixes: a5f276f10ff7 ("serial_core: Handle TIOC[GS]RS485 ioctls.")
Fixes: ad8c0eaa0a41 ("tty/serial_core: add ISO7816 infrastructure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 5099d234a52a ("serial_core: switch to ->[sg]et_serial()")
the serial structure passed to uart_get_info() has already have been
cleared by the tty layer so drop the redundant memset.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usage of in_interrupt() in drivers is phased out for various
reasons.
In both exported functions where BUG_ON(in_interrupt()) is invoked,
there is a mutex_lock() afterwards. mutex_lock() contains a
might_sleep() which will already trigger a stack trace if the target
functions is called from atomic context.
Remove the BUG_ON() and add a "Context: " in the kernel-doc instead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210208181615.381861-3-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The main purpose of tty_port::low_latency was removed in commit
a9c3f68f3cd8 (tty: Fix low_latency BUG) back in 2014. It was left in
place for drivers as an optional tune knob. But only one driver has been
using it until the previous commit. So remove this misconcept
completely, given there are no users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the port-lock initialisation regression introduced by commit
a3cb39d258ef ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3ec ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit f743061a85f5 ("serial: core: Initialise spin lock before use in
uart_configure_port()") tried to work around a breakage introduced by
commit a3cb39d258ef ("serial: core: Allow detach and attach serial
device for console") by adding a second initialisation of the port lock
when registering the port.
As reported by the build robots [1], this doesn't really solve the
regression introduced by the console-detach changes and also adds a
second redundant initialisation of the lock for normal ports.
Start cleaning up this mess by removing the redundant initialisation and
making sure that the port lock is again initialised once-only for ports
that aren't already in use as a console.
[1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian
Fixes: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
