| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm subsystem from Dan Williams:
"The libnvdimm sub-system introduces, in addition to the
libnvdimm-core, 4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory
devices (NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware
Interface table).
After registering NVDIMMs the NFIT driver then registers "region"
devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block
device (disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of
persistent memory address ranges is re-worked to drive
PMEM-namespaces emitted by the libnvdimm-core.
In this update the PMEM driver, on x86, gains the ability to assert
that writes to persistent memory have been flushed all the way
through the caches and buffers in the platform to persistent media.
See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through
"Block Data Windows" as defined by the NFIT. The primary difference
of this driver to PMEM is that only a small window of persistent
memory is mapped into system address space at any given point in
time.
Per-NVDIMM windows are reprogrammed at run time, per-I/O, to access
different portions of the media. BLK-mode, by definition, does not
support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss).
The sinister aspect of sector tearing is that most applications do
not know they have a atomic sector dependency. At least today's
disk's rarely ever tear sectors and if they do one almost certainly
gets a CRC error on access. NVDIMMs will always tear and always
silently. Until an application is audited to be robust in the
presence of sector-tearing the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore"
* tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm: (33 commits)
arch, x86: pmem api for ensuring durability of persistent memory updates
libnvdimm: Add sysfs numa_node to NVDIMM devices
libnvdimm: Set numa_node to NVDIMM devices
acpi: Add acpi_map_pxm_to_online_node()
libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only
pmem: flag pmem block devices as non-rotational
libnvdimm: enable iostat
pmem: make_request cleanups
libnvdimm, pmem: fix up max_hw_sectors
libnvdimm, blk: add support for blk integrity
libnvdimm, btt: add support for blk integrity
fs/block_dev.c: skip rw_page if bdev has integrity
libnvdimm: Non-Volatile Devices
tools/testing/nvdimm: libnvdimm unit test infrastructure
libnvdimm, nfit, nd_blk: driver for BLK-mode access persistent memory
nd_btt: atomic sector updates
libnvdimm: infrastructure for btt devices
libnvdimm: write blk label set
libnvdimm: write pmem label set
libnvdimm: blk labels and namespace instantiation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest update from Shuah Khan:
"This update adds two new test suites: futex and seccomp.
In addition, it includes fixes for bugs in timers, other tests, and
compile framework. It introduces new quicktest feature to enable
users to choose to run tests that complete in a short time"
* tag 'linux-kselftest-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: add quicktest support
selftests: add seccomp suite
selftest, x86: fix incorrect comment
tools selftests: Fix 'clean' target with make 3.81
selftests/futex: Add .gitignore
kselftest: Add exit code defines
selftests: Add futex tests to the top-level Makefile
selftests/futex: Increment ksft pass and fail counters
selftests/futex: Update Makefile to use lib.mk
selftests: Add futex functional tests
kselftests: timers: Check _ALARM clockids are supported before suspending
kselftests: timers: Ease alarmtimer-suspend unreasonable latency value
kselftests: timers: Increase delay between suspends in alarmtimer-suspend
selftests/exec: do not install subdir as it is already created
selftests/ftrace: install test.d
selftests: copy TEST_DIRS to INSTALL_PATH
Test compaction of mlocked memory
selftests/mount: output WARN messages when mount test skipped
selftests/timers: Make git ignore all binaries in timers test suite
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn,
and a few new drivers as well, one of which I just disabled from the
build a few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues"
* tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1163 commits)
staging: wilc1000: disable driver due to build warnings
Staging: rts5208: fix CHANGE_LINK_STATE value
Staging: sm750fb: ddk750_swi2c.c: Insert spaces before parenthesis
Staging: sm750fb: ddk750_swi2c.c: Place braces on correct lines
Staging: sm750fb: ddk750_swi2c.c: Insert spaces around operators
Staging: sm750fb: ddk750_swi2c.c: Replace spaces with tabs
Staging: sm750fb: ddk750_swi2c.h: Shorten lines to under 80 characters
Staging: sm750fb: ddk750_swi2c.h: Replace spaces with tabs
Staging: sm750fb: modedb.h: Shorten lines to under 80 characters
Staging: sm750fb: modedb.h: Replace spaces with tabs
staging: comedi: addi_apci_3120: rename 'this_board' variables
staging: comedi: addi_apci_1516: rename 'this_board' variables
staging: comedi: ni_atmio: cleanup ni_getboardtype()
staging: comedi: vmk80xx: sanity check context used to get the boardinfo
staging: comedi: vmk80xx: rename 'boardinfo' variables
staging: comedi: dt3000: rename 'this_board' variables
staging: comedi: adv_pci_dio: rename 'this_board' variables
staging: comedi: cb_pcidas64: rename 'thisboard' variables
staging: comedi: cb_pcidas: rename 'thisboard' variables
staging: comedi: me4000: rename 'thisboard' variables
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This patch series contains several clean ups and even a new trace
clock "monitonic raw". Also some enhancements to make the ring buffer
even faster. But the biggest and most noticeable change is the
renaming of the ftrace* files, structures and variables that have to
deal with trace events.
Over the years I've had several developers tell me about their
confusion with what ftrace is compared to events. Technically,
"ftrace" is the infrastructure to do the function hooks, which include
tracing and also helps with live kernel patching. But the trace
events are a separate entity altogether, and the files that affect the
trace events should not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled() -> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not
heard a single complaint about this rename breaking anything. Mostly
because these functions, variables and structures are mostly internal
to the tracing system and are seldom (if ever) used by anything
external to that"
* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
ring_buffer: Allow to exit the ring buffer benchmark immediately
ring-buffer-benchmark: Fix the wrong type
ring-buffer-benchmark: Fix the wrong param in module_param
ring-buffer: Add enum names for the context levels
ring-buffer: Remove useless unused tracing_off_permanent()
ring-buffer: Give NMIs a chance to lock the reader_lock
ring-buffer: Add trace_recursive checks to ring_buffer_write()
ring-buffer: Allways do the trace_recursive checks
ring-buffer: Move recursive check to per_cpu descriptor
ring-buffer: Add unlikelys to make fast path the default
tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
tracing: Rename ftrace_event_name() to trace_event_name()
tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
...
|
|
Upon detection of an unarmed dimm in a region, arrange for descendant
BTT, PMEM, or BLK instances to be read-only. A dimm is primarily marked
"unarmed" via flags passed by platform firmware (NFIT).
The flags in the NFIT memory device sub-structure indicate the state of
the data on the nvdimm relative to its energy source or last "flush to
persistence". For the most part there is nothing the driver can do but
advertise the state of these flags in sysfs and emit a message if
firmware indicates that the contents of the device may be corrupted.
However, for the case of ACPI_NFIT_MEM_ARMED, the driver can arrange for
the block devices incorporating that nvdimm to be marked read-only.
This is a safe default as the data is still available and new writes are
held off until the administrator either forces read-write mode, or the
energy source becomes armed.
A 'read_only' attribute is added to REGION devices to allow for
overriding the default read-only policy of all descendant block devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
'libnvdimm' is the first driver sub-system in the kernel to implement
mocking for unit test coverage. The nfit_test module gets built as an
external module and arranges for external module replacements of nfit,
libnvdimm, nd_pmem, and nd_blk. These replacements use the linker
--wrap option to redirect calls to ioremap() + request_mem_region() to
custom defined unit test resources. The end result is a fully
functional nvdimm_bus, as far as userspace is concerned, but with the
capability to perform otherwise destructive tests on emulated resources.
Q: Why not use QEMU for this emulation?
QEMU is not suitable for unit testing. QEMU's role is to faithfully
emulate the platform. A unit test's role is to unfaithfully implement
the platform with the goal of triggering bugs in the corners of the
sub-system implementation. As bugs are discovered in platforms, or the
sub-system itself, the unit tests are extended to backstop a fix with a
reproducer unit test.
Another problem with QEMU is that it would require coordination of 3
software projects instead of 2 (kernel + libndctl [1]) to maintain and
execute the tests. The chances for bit rot and the difficulty of
getting the tests running goes up non-linearly the more components
involved.
Q: Why submit this to the kernel tree instead of external modules in
libndctl?
Simple, to alleviate the same risk that out-of-tree external modules
face. Updates to drivers/nvdimm/ can be immediately evaluated to see if
they have any impact on tools/testing/nvdimm/.
Q: What are the negative implications of merging this?
It is a unique maintenance burden because the purpose of mocking an
interface to enable a unit test is to purposefully short circuit the
semantics of a routine to enable testing. For example
__wrap_ioremap_cache() fakes the pmem driver into "ioremap()'ing" a test
resource buffer allocated by dma_alloc_coherent(). The future
maintenance burden hits when someone changes the semantics of
ioremap_cache() and wonders what the implications are for the unit test.
[1]: https://github.com/pmem/ndctl
Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull documentation updates from Jonathan Corbet:
"The main thing here is Ingo's big subdirectory documenting feature
support for each architecture. Beyond that, it's the usual pile of
fixes, tweaks, and small additions"
* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6: (79 commits)
doc:md: fix typo in md.txt.
Documentation/mic/mpssd: don't build x86 userspace when cross compiling
Documentation/prctl: don't build tsc tests when cross compiling
Documentation/vDSO: don't build tests when cross compiling
Doc:ABI/testing: Fix typo in sysfs-bus-fcoe
Doc: Docbook: Change wikipedia's URL from http to https in scsi.tmpl
Doc: Change wikipedia's URL from http to https
Documentation/kernel-parameters: add missing pciserial to the earlyprintk
Doc:pps: Fix typo in pps.txt
kbuild : Fix documentation of INSTALL_HDR_PATH
Documentation: filesystems: updated struct file_operations documentation in vfs.txt
kbuild: edit explanation of clean-files variable
Doc: ja_JP: Fix typo in HOWTO
Move freefall program from Documentation/ to tools/
Documentation: ARM: EXYNOS: Describe boot loaders interface
Doc:nfc: Fix typo in nfc-hci.txt
vfs: Minor documentation fix
Doc: networking: txtimestamp: fix printf format warning
Documentation, intel_pstate: Improve legacy mode internal governors description
Documentation: extend use case for EXPORT_SYMBOL_GPL()
...
|
|
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
|
|
Add quicktest support to enable users to choose to run
tests that complete in a short time. Choosing this option
excludes tests that take longer time complete e.g: timers.
User can specify quicktest option from kernel top level or
selftests directory.
Kernel top level directory:
make quicktest=1 kselftest
tools/testing/selftests directory:
make quicktest=1 run_tests
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather largish update for everything time and timer related:
- Cache footprint optimizations for both hrtimers and timer wheel
- Lower the NOHZ impact on systems which have NOHZ or timer migration
disabled at runtime.
- Optimize run time overhead of hrtimer interrupt by making the clock
offset updates smarter
- hrtimer cleanups and removal of restrictions to tackle some
problems in sched/perf
- Some more leap second tweaks
- Another round of changes addressing the 2038 problem
- First step to change the internals of clock event devices by
introducing the necessary infrastructure
- Allow constant folding for usecs/msecs_to_jiffies()
- The usual pile of clockevent/clocksource driver updates
The hrtimer changes contain updates to sched, perf and x86 as they
depend on them plus changes all over the tree to cleanup API changes
and redundant code, which got copied all over the place. The y2038
changes touch s390 to remove the last non 2038 safe code related to
boot/persistant clock"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
clocksource: Increase dependencies of timer-stm32 to limit build wreckage
timer: Minimize nohz off overhead
timer: Reduce timer migration overhead if disabled
timer: Stats: Simplify the flags handling
timer: Replace timer base by a cpu index
timer: Use hlist for the timer wheel hash buckets
timer: Remove FIFO "guarantee"
timers: Sanitize catchup_timer_jiffies() usage
hrtimer: Allow hrtimer::function() to free the timer
seqcount: Introduce raw_write_seqcount_barrier()
seqcount: Rename write_seqcount_barrier()
hrtimer: Fix hrtimer_is_queued() hole
hrtimer: Remove HRTIMER_STATE_MIGRATE
selftest: Timers: Avoid signal deadlock in leap-a-day
timekeeping: Copy the shadow-timekeeper over the real timekeeper last
clockevents: Check state instead of mode in suspend/resume path
selftests: timers: Add leap-second timer edge testing to leap-a-day.c
ntp: Do leapsecond adjustment in adjtimex read path
time: Prevent early expiry of hrtimers[CLOCK_REALTIME] at the leap second edge
ntp: Introduce and use SECS_PER_DAY macro instead of 86400
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"These are the left over fixes from the v4.1 cycle"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix build breakage if prefix= is specified
perf/x86: Honor the architectural performance monitoring version
perf/x86/intel: Fix PMI handling for Intel PT
perf/x86/intel/bts: Fix DS area sharing with x86_pmu events
perf/x86: Add more Broadwell model numbers
perf: Fix ring_buffer_attach() RCU sync, again
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes mostly consist of work on x86 PMU drivers:
- x86 Intel PT (hardware CPU tracer) improvements (Alexander
Shishkin)
- x86 Intel CQM (cache quality monitoring) improvements (Thomas
Gleixner)
- x86 Intel PEBSv3 support (Peter Zijlstra)
- x86 Intel PEBS interrupt batching support for lower overhead
sampling (Zheng Yan, Kan Liang)
- x86 PMU scheduler fixes and improvements (Peter Zijlstra)
There's too many tooling improvements to list them all - here are a
few select highlights:
'perf bench':
- Introduce new 'perf bench futex' benchmark: 'wake-parallel', to
measure parallel waker threads generating contention for kernel
locks (hb->lock). (Davidlohr Bueso)
'perf top', 'perf report':
- Allow disabling/enabling events dynamicaly in 'perf top':
a 'perf top' session can instantly become a 'perf report'
one, i.e. going from dynamic analysis to a static one,
returning to a dynamic one is possible, to toogle the
modes, just press 'f' to 'freeze/unfreeze' the sampling. (Arnaldo Carvalho de Melo)
- Make Ctrl-C stop processing on TUI, allowing interrupting the load of big
perf.data files (Namhyung Kim)
'perf probe': (Masami Hiramatsu)
- Support glob wildcards for function name
- Support $params special probe argument: Collect all function arguments
- Make --line checks validate C-style function name.
- Add --no-inlines option to avoid searching inline functions
- Greatly speed up 'perf probe --list' by caching debuginfo.
- Improve --filter support for 'perf probe', allowing using its arguments
on other commands, as --add, --del, etc.
'perf sched':
- Add option in 'perf sched' to merge like comms to lat output (Josef Bacik)
Plus tons of infrastructure work - in particular preparation for
upcoming threaded perf report support, but also lots of other work -
and fixes and other improvements. See (much) more details in the
shortlog and in the git log"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (305 commits)
perf tools: Configurable per thread proc map processing time out
perf tools: Add time out to force stop proc map processing
perf report: Fix sort__sym_cmp to also compare end of symbol
perf hists browser: React to unassigned hotkey pressing
perf top: Tell the user how to unfreeze events after pressing 'f'
perf hists browser: Honour the help line provided by builtin-{top,report}.c
perf hists browser: Do not exit when 'f' is pressed in 'report' mode
perf top: Replace CTRL+z with 'f' as hotkey for enable/disable events
perf annotate: Rename source_line_percent to source_line_samples
perf annotate: Display total number of samples with --show-total-period
perf tools: Ensure thread-stack is flushed
perf top: Allow disabling/enabling events dynamicly
perf evlist: Add toggle_enable() method
perf trace: Fix race condition at the end of started workloads
perf probe: Speed up perf probe --list by caching debuginfo
perf probe: Show usage even if the last event is skipped
perf tools: Move libtraceevent dynamic list to separated LDFLAGS variable
perf tools: Fix a problem when opening old perf.data with different byte order
perf tools: Ignore .config-detected in .gitignore
perf probe: Fix to return error if no probe is added
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
- Continued initialization/Kconfig updates: hide most Kconfig options
from unsuspecting users.
There's now a single high level configuration option:
*
* RCU Subsystem
*
Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)
Which if answered in the negative, leaves us with a single
interactive configuration option:
Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)
All the rest of the RCU options are configured automatically. Later
on we'll remove this single leftover configuration option as well.
- Remove all uses of RCU-protected array indexes: replace the
rcu_[access|dereference]_index_check() APIs with READ_ONCE() and
rcu_lockdep_assert()
- RCU CPU-hotplug cleanups
- Updates to Tiny RCU: a race fix and further code shrinkage.
- RCU torture-testing updates: fixes, speedups, cleanups and
documentation updates.
- Miscellaneous fixes
- Documentation updates
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
rcutorture: Allow repetition factors in Kconfig-fragment lists
rcutorture: Display "make oldconfig" errors
rcutorture: Update TREE_RCU-kconfig.txt
rcutorture: Make rcutorture scripts force RCU_EXPERT
rcutorture: Update configuration fragments for rcutree.rcu_fanout_exact
rcutorture: TASKS_RCU set directly, so don't explicitly set it
rcutorture: Test SRCU cleanup code path
rcutorture: Replace barriers with smp_store_release() and smp_load_acquire()
locktorture: Change longdelay_us to longdelay_ms
rcutorture: Allow negative values of nreaders to oversubscribe
rcutorture: Exchange TREE03 and TREE08 NR_CPUS, speed up CPU hotplug
rcutorture: Exchange TREE03 and TREE04 geometries
locktorture: fix deadlock in 'rw_lock_irq' type
rcu: Correctly handle non-empty Tiny RCU callback list with none ready
rcutorture: Test both RCU-sched and RCU-bh for Tiny RCU
rcu: Further shrink Tiny RCU by making empty functions static inlines
rcu: Conditionally compile RCU's eqs warnings
rcu: Remove prompt for RCU implementation
rcu: Make RCU able to tolerate undefined CONFIG_RCU_KTHREAD_PRIO
rcu: Make RCU able to tolerate undefined CONFIG_RCU_FANOUT_LEAF
...
|
|
The time out to limit the individual proc map processing was hard code
to 500ms. This patch introduce a new option --proc-map-timeout to make
the time limit configurable.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ying Huang <ying.huang@intel.com>
Link: http://lkml.kernel.org/r/1434549071-25611-2-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
System wide sampling like 'perf top' or 'perf record -a' read all
threads /proc/xxx/maps before sampling. If there are any threads which
generating a keeping growing huge maps, perf will do infinite loop
during synthesizing. Nothing will be sampled.
This patch fixes this issue by adding per-thread timeout to force stop
this kind of endless proc map processing.
PERF_RECORD_MISC_PROC_MAP_PARSE_TIME_OUT is introduced to indicate that
the mmap record are truncated by time out. User will get warning
notification when truncated mmap records are detected.
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ying Huang <ying.huang@intel.com>
Link: http://lkml.kernel.org/r/1434549071-25611-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When using a map file from a JIT, due to memory reuse, we can obtain
multiple symbols with the same start address but a different length.
The symbols__find does check for the end so not doing it in
sort__sym_cmp was causing the hist_entry in the annotate part of a
report to match to the wrong entry, causing a fatal error.
Signed-off-by: Yannick Brosseau <scientist@fb.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/1434584470-17771-1-git-send-email-scientist@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When that happens we were just ignoring the key press, now this
message is presented in the bottom line (the help line):
"Press '?' for help on key bindings"
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-iyma2j5kj3q9i1stl4mfh90n@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When the user presses 'f' to disable events the visual cues are, well,
the percentages not changing and the number of events freezing.
Be more explicit by changing the help line at the bottom of the screen
to show the following messages when 'f' is pressed:
"Press 'f' again to re-enable the events"
And then, when 'f' is pressed again:
"Press 'f' to disable the events or 'h'
Suggested-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-uhiswg9a9rxm5gxg7ptjskjn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The hists_browser was replacing whatever helpline provided by 'top' or
'report' with a static "Press '?' for help on key bindings", fix it.
Now the message passed by top appears at the bottom of the screen:
"For a higher level overview, try: perf top --sort comm,dso"
As well the message that will be added when the user presses 'f' to
disable the events, something along the lines of "press f again to
re-enable...".
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-dacaja70mbfz3a0yj1n180gx@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The 'f' hotkey is only used when in 'top', dynamic mode, to
enable/disable events, currently not making sense in the 'report',
static mode, where we can't go from showing the histogram entries
created from a perf.data file to adding more events after recreating the
evlist created from the perf.data file, albeit possible, this is not
implemented right now.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-lholzf472pu98dkkijggwx2m@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
I.e. 'freeze'/'unfreeze', this is because CTRL+z has a well known
action, i.e. suspend the app, perf needs to follow that convention, that
will be done on a separate patch, tho.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-oedcl6ovohara4koig14ayip@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Invoking Makefile.perf with prefix= breaks the build since Makefile.perf
hands that variable down to Makefile.build where it overrides
prefix := $(subst ./,,$(OUTPUT)$(dir)/)
leading to errors like this:
No rule to make target '/usrabspath.o', needed by '/usrlibperf-in.o'
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Fixes: c819e2cf2eb6f65d3208d195d7a0edef6108d5
Link: http://lkml.kernel.org/r/5582c48a.84a22b0a.a918.5285SMTPIN_ADDED_MISSING@mx.google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To better reflect the purpose of this struct, that is to hold
info about samples, its total number and is percentage.
Cc: Martin Liska <mliska@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/n/tip-6bf8gwcl975uurl0ttpvtk69@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To compare two records on an instruction base, with --show-total-period
option provided, display total number of samples that belong to a line
in assembly language.
New hot key 't' is introduced for 'perf annotate' TUI.
Signed-off-by: Martin Liska <mliska@suse.cz>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/5583E26D.1040407@suse.cz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The thread-stack represents a thread's current stack. When a thread
exits there can still be many functions on the stack e.g. exit() can be
called many levels deep, so all the callers will never return. To get
that information output, the thread-stack must be flushed.
Previously it was assumed the thread-stack would be flushed when the
struct thread was deleted. With thread ref-counting it is no longer
clear when that will be, if ever. So instead explicitly flush all the
thread-stacks at the end of a session.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1432906425-9911-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return very early without
performing the syscall and keeping side effects to a minimum (no CPU
accounting or system call tracing is performed). Also included is a
new HWCAP2 bit, PPC_FEATURE2_HTM_NOSC, to indicate this
behaviour to userspace.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality as
syscalls will still be performed after tsuspend; it just requires that
the transaction be explicitly suspended. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c indicate the cost of
a normal (non-aborted) system call increases by about 0.25%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
* pnp:
PNP / ACPI: use unsigned int in pnpacpi_encode_resources()
PNP / ACPI: use u8 instead of int in acpi_resource_extended_irq context
* pm-tools:
cpupower: mperf monitor: fix output in MAX_FREQ_SYSFS mode
|
|
In 0c4a5fc95b1df (Add leap-second timer edge testing to
leap-a-day.c), we added a timer to the test which checks to make
sure timers near the leapsecond edge behave correctly.
However, the output generated from the timer uses ctime_r, which
isn't async-signal safe, and should that signal land while the
main test is using ctime_r to print its output, its possible for
the test to deadlock on glibc internal locks.
Thus this patch reworks the output to avoid using ctime_r in
the signal handler.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1434565003-3386-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This imports the existing seccomp test suite into the kernel's selftests
tree. It contains extensive testing of seccomp features and corner cases.
There remain additional tests to move into the kernel tree, but they have
not yet been ported to all the architectures seccomp supports:
https://github.com/redpig/seccomp/tree/master/tests
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Now it is possible to press CTRL+z at anytime and that will disable the
events being monitored, essentially turning 'top' into 'report', with
pressing CTRL+z again making it enable the events again, returning to
the 'top' behaviour, i.e. dynamic + decaying of older samples.
One may want, for instance, play with:
-d, --delay <n> number of seconds to delay between refreshes
and:
-z, --zero zero history across updates
Plus CTRL+z to see only the events since last zeroing, etc.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-zq7tnh5462blt2yda0bcxh5b@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
For an upcoming feature in 'perf top' we will have a hotkey to
enable/disable events, so remember if the events in the list are
enabled or disabled and allows toggling this state using a new
method.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-64c4jvdl5feg2zhimxvokqka@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
I get following crash on multiple systems and across several releases
(at least since v3.18).
Core was generated by `/tmp/perf trace sleep 0.2 '.
Program terminated with signal SIGSEGV, Segmentation fault.
#0 perf_mmap__read_head (mm=0x3fff9bf30070) at util/evlist.h:195
195 u64 head = ACCESS_ONCE(pc->data_head);
(gdb) bt
#0 perf_mmap__read_head (mm=0x3fff9bf30070) at util/evlist.h:195
#1 perf_evlist__mmap_read (evlist=0x10027f11910, idx=<optimized out>)
at util/evlist.c:637
#2 0x000000001003ce4c in trace__run (argv=<optimized out>,
argc=<optimized out>, trace=0x3fffd7b28288) at builtin-trace.c:2259
#3 cmd_trace (argc=<optimized out>, argv=<optimized out>,
prefix=<optimized out>) at builtin-trace.c:2799
#4 0x00000000100657b8 in run_builtin (p=0x10176798 <commands+480>, argc=3,
argv=0x3fffd7b2b550) at perf.c:370
#5 0x00000000100063e8 in handle_internal_command (argv=0x3fffd7b2b550, argc=3)
at perf.c:429
#6 run_argv (argv=0x3fffd7b2af70, argcp=0x3fffd7b2af7c) at perf.c:473
#7 main (argc=3, argv=0x3fffd7b2b550) at perf.c:588
The problem seems to be a race condition, when the application has just
exited. Some/all fds associated with the perf-events (tracepoints) go
into a POLLHUP/ POLLERR state and the mmap region associated with those
events are unmapped (in perf_evlist__filter_pollfd()).
But we go back and do a perf_evlist__mmap_read() which assumes that the
mmaps are still valid and we hit the crash.
If the mapping for an event is released, its refcnt is 0 (and ->base
is NULL), so ensure we have non-zero refcount before accessing the map.
Note that perf-record has a similar logic but unlike perf-trace, the
record__mmap_read_all() checks the evlist->mmap[i].base before accessing
the map.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Li Zhang <zhlcindy@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20150612060003.GA19913@us.ibm.com
[ Fixed it up to use atomic_read() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Speed up the "perf probe --list" by caching the last used debuginfo.
perf probe --list always open and load debuginfo for each entry of probe
list. This takes very a long time.
E.g. with vfs_* events (total 96 probes)
[root@localhost perf]# time ./perf probe -l &> /dev/null
real 0m25.376s
user 0m24.381s
sys 0m1.012s
To solve this issue, this adds debuginfo_cache to cache the
last used debuginfo on memory.
With this fix, the perf-probe --list significantly improves
its speed.
[root@localhost perf]# time ./perf probe -l &> /dev/null
real 0m0.161s
user 0m0.136s
sys 0m0.025s
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naohiro Aota <naota@elisp.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150617145854.19715.15314.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When the last part of converted events are blacklisted or out-of-text,
those are skipped and perf probe doesn't show usage examples. This
fixes it to show the example even if the last part of event list is
skipped.
E.g. without this patch, events are added, but suddenly end:
# perf probe vfs_*
vfs_caches_init_early is out of .text, skip it.
vfs_caches_init is out of .text, skip it.
Added new events:
probe:vfs_fallocate (on vfs_*)
probe:vfs_open (on vfs_*)
...
probe:vfs_dentry_acceptable (on vfs_*)
probe:vfs_load_quota_inode (on vfs_*)
#
With this fix:
# perf probe vfs_*
vfs_caches_init_early is out of .text, skip it.
vfs_caches_init is out of .text, skip it.
Added new events:
probe:vfs_fallocate (on vfs_*)
...
probe:vfs_load_quota_inode (on vfs_*)
You can now use it in all perf tools, such as:
perf record -e probe:vfs_load_quota_inode -aR sleep 1
Note that this can be reproduced ONLY IF the vfs_caches_init* is the
last part of matched symbol list. I've checked this happens on
"3.19.0-generic #18-Ubuntu" kernel binary.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naohiro Aota <naota@elisp.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150616115057.19906.5502.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit e3d09ec8126fe2c9a3ade661e2126e215ca27a80 ("tools lib traceevent:
Export dynamic symbols used by traceevent plugins") adds libtraceevent
dynamic list directly into LDFLAGS, which makes all targets depend on
that list through LDFLAGS.
This is not good since some of targets like libgtk.so doesn't use plugin
at all, but require the existance of that list because of linker
options.
This patch isolates the -Xlink option into LIBTRACEEVENT_DYNAMIC_LIST_LDFLAGS,
makes only perf and perf.so use it.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: He Kuang <hekuang@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1434552389-89144-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Following error occurs when trying to use 'perf report' on x86_64 to
cross analysis a perf.data generated by an old perf on a big-endian
machine:
# perf report
*** Error in `/home/w00229757/perf': free(): invalid next size (fast): 0x00000000032c99f0 ***
======= Backtrace: =========
/lib64/libc.so.6(+0x6eeef)[0x7ff6ff7e2eef]
/lib64/libc.so.6(+0x78cae)[0x7ff6ff7eccae]
/lib64/libc.so.6(+0x79987)[0x7ff6ff7ed987]
/path/to/perf[0x4ac734]
/path/to/perf[0x4ac829]
/path/to/perf(perf_header__process_sections+0x129)[0x4ad2c9]
/path/to/perf(perf_session__read_header+0x2e1)[0x4ad9e1]
/path/to/perf(perf_session__new+0x168)[0x4bd458]
/path/to/perf(cmd_report+0xfa0)[0x43eb70]
/path/to/perf[0x47adc3]
/path/to/perf(main+0x5f6)[0x42fd06]
/lib64/libc.so.6(__libc_start_main+0xf5)[0x7ff6ff795bd5]
/path/to/perf[0x42fe35]
======= Memory map: ========
[SNIP]
The bug is in perf_event__attr_swap(). It swaps all fields in 'struct
perf_event_attr' without checking whether the swapped field exist or
not. In addition, in read_event_desc() allocs memory for attr according
to size read from perf.data.
Therefore, if the perf.data is collected by an old perf (without
aux_watermark, for example), when perf_event__attr_swap() swaping
attr->aux_watermark it destroy malloc's metadata.
This patch introduces boundary checking in perf_event__attr_swap(). It
adds macros bswap_field_64 and bswap_field_32 into
perf_event__attr_swap() to make it only swap exist fields.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1434534999-85347-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit fcfd6611fbccdbf2593bd949097a5c0e45cd96da ("tools build: Add
detected config support") dynamically creates .config-detected. Add it
to .gitignore.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/1434542358-5430-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix perf probe to return an error if no probe is added due to the given
probe point being on the blacklist.
To fix this problem, this moves the blacklist checking to right after
finding symbols/probe-points and marks them as skipped.
If all the symbols are skipped, "perf probe" returns an error as it
fails to find the corresponding probe address.
E.g. currently if a blacklisted probe is given:
# perf probe do_trap && echo 'succeed'
Added new event:
Warning: Skipped probing on blacklisted function: sync_regs
succeed
No! It must fail! With this patch, it correctly fails:
# perf probe do_trap && echo 'succeed'
do_trap is blacklisted function, skip it.
Probe point 'do_trap' not found.
Error: Failed to add events.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naohiro Aota <naota@elisp.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150616115055.19906.31359.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When libunwind is on, there is a compile error as :
util/unwind-libunwind.c:363:21: error: 'dso' undeclared (first use in this function)
dso__data_put_fd(dso);
This patch fixes it.
Signed-off-by: Hou Pengyang <houpengyang@huawei.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 4bb11d012ab248d0 ("perf tools: Add dso__data_get/put_fd()")
Link: http://lkml.kernel.org/r/1434453395-10560-1-git-send-email-houpengyang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Move 'struct perf_counts' allocation|free|reset code into separate
functions.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1434269985-521-13-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
It's stat specific. Updating python build objects with stat.c.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1434269985-521-12-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
In order to have 'struct thread_map' allocation on single place and can
change it easily in following patch.
Using alloc|realloc for static helpers, because thread_map__new is
already used in public interface.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1434269985-521-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To zero all the xyarray contents. It will be used in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1434269985-521-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Since commit 5e17b28f1e24 ("perf probe: Add --quiet option to
suppress output result message") have replaced printf with pr_info,
perf probe -l outputs its result in stderr. However, that is not
what the commit expected.
E.g.:
# perf probe -l > /dev/null
probe:vfs_read (on vfs_read@ksrc/linux-3/fs/read_write.c)
With this fix:
# perf probe -l > list
# cat list
probe:vfs_read (on vfs_read@ksrc/linux-3/fs/read_write.c)
Of course, --quiet(-q) still works on --add/--del.
# perf probe -q vfs_write
# perf probe -l
probe:vfs_read (on vfs_read@ksrc/linux-3/fs/read_write.c)
probe:vfs_write (on vfs_write@ksrc/linux-3/fs/read_write.c)
-----
Reported-by: Naohiro Aota <naota@elisp.net>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naohiro Aota <naota@elisp.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150613013116.24402.2923.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
'make build-test' finds an error that make_python_perf_so fails due to
missing of libtraceevent-dynamic-list:
'.../python2' util/setup.py \
--quiet build_ext; \
mkdir -p python && \
cp python_ext_build/lib/perf.so python/
/path/to/ld: cannot open linker script file /path/to/kernel/tools/lib/traceevent/libtraceevent-dynamic-list: No such file or directory
collect2: error: ld returned 1 exit status
error: command 'x86_64-linux-gcc' failed with exit status 1
cp: cannot stat 'python_ext_build/lib/perf.so': No such file or directory
make[3]: *** [python/perf.so] Error 1
make[2]: *** [python/perf.so] Error 2
test: test -f ./python/perf.so
make[1]: *** [make_python_perf_so] Error 1
make: *** [build-test] Error 2
make: Leaving directory `/path/to/kernel/tools/perf'
This is caused by commit e3d09ec8126fe2c9a3ade661e2126e215ca27a80
("tools lib traceevent: Export dynamic symbols used by traceevent
plugins") that, it adds the list file to LDFLAGS but forgot to add it to
dependency list of python/perf.so.
This patch fixes this problem.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: He Kuang <hekuang@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/1434079031-123162-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Use just reference counts, so that when no more hist_entry instances
references a map and the thread instance goes away by processing a
PERF_RECORD_EXIT, we can delete the maps.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-oym7lfhcc7ss6xpz44h7nbxs@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
