Age | Commit message (Collapse) | Author |
|
|
|
|
|
Node that extrudes vertices, edges and Faces. Uses the
corresponding bmesh operator.
I renamed D12108, which was previously named Mesh Extrude to Mesh Inset,
because that uses the bmesh inset operators.
NOTE: This requires an update of the attribute interpolation to work,
that is not yet in master.
Part of the GSOC 2021
Differential Revision: https://developer.blender.org/D12224
|
|
# Conflicts:
# source/blender/blenkernel/BKE_node.h
|
|
|
|
This reverts commit 41e650981861c2f18ab0548e18851d1d761066ff.
This broke "CubeMaskFirst" test.
Any value even slightly outside the [-1.0..1.0] range
caused the result to be nan, which can happen when calculating
the dot-product between two unit length vectors.
|
|
The clamped version of acos isn't needed as degenerate (nan) coordinates
result in zeroed vectors which don't need clamping.
|
|
Caused by fix for T90256 and a misunderstanding in D11928.
Don't skip tagging edges when the auto-smooth angle is 180 degrees
since this skips topology checks which are needed for properly
calculating edge loop normals.
|
|
|
|
|
|
Follow the same logic already used by the modifier.
|
|
Also remove redundant fabsf on the area of a quad/tri &
reduce indentation using continue in for loop.
|
|
Only vertex indices were ensured to be correct.
|
|
Vertices with no connected faces would attempt to divide by the combined
face area causing a divide by zero.
Use the same weight for wire vertices as vertices connected
to zero area faces.
|
|
Regression in 39b2a7bb7e815e051348bf5c5ec777d091324164.
|
|
This makes the internal naming consistent with the public API. And also gives
us a visibility_flag rather than restrictflag that can be extended with more
flags.
|
|
Error in 39b2a7bb7e815e051348bf5c5ec777d091324164
which failed to set edge flags with single threaded calculation,
used for low poly models.
|
|
|
|
|
|
|
|
Differential Revision: https://developer.blender.org/D12108
|
|
Regression in 39b2a7bb7e815e051348bf5c5ec777d091324164
that meant non-manifold edges were not being tagged
when they should have been.
|
|
This BMesh iterator hadn't been used in C++ code yet, and needed
a macro for a proper cast. The parameter structs need to be initialized
when declared without designated initializers.
|
|
|
|
|
|
Six years ago, Bug T44961 about unwanted spikes had me not do a loop
slide if the angle was too extreme, to avoid unwanted spikes.
The current bug showed that that angle was much too big, and limited
desired behavior in many cases. Changing the angle from 0.25 radians
to 0.0001 radians (about 0.006 degrees) still fixes the original bug
and seems very unlikely to be limiting desired behavior now.
|
|
|
|
Share functionality for single and multi-threaded edge-split tagging.
Remove logic that ensured vert & loop indices in bm_mesh_edges_sharp_tag
(missing from fd9fc809b76d625a1ead6e1fbe5e486cc012f5f3).
|
|
The only difference with BM_loops_calc_normal_vcos was passing in
custom coordinates which may be NULL.
|
|
bm_mesh_edges_sharp_tag was called with setting sharp edges enabled.
Error in 39b2a7bb7e815e051348bf5c5ec777d091324164.
|
|
This was added in 0b7f5813973c515b84cd7c18ef6d7d1e59374237
but seems not to be needed as the assignment was never correct
since only one corner on either side of the smooth edge had the
vertex normal written to it.
|
|
Merge the sharp edge tagging into bm_mesh_loops_calc_normals,
this has the advantage that edge tagging can be performed as part of
walking over each vertices edges - instead of tagging in a separate loop.
Even though this will tag edges twice (once for each vertex),
the computation isn't heavy as it's only calculating a dot-product
between the two face users to compare the angle.
This change combined with 4ba06ad0a8cdec66d9a9cb06f982736d46c40f4c
makes BM_loops_calc_normal_vcos around 5.68x faster,
with an overall speedup over 2.6x when transforming a high poly mesh.
(tested on a system with 32 cores).
Reviewed By: mont29
Ref D11970
|
|
Supported multi-threading for bm_mesh_loops_calc_normals.
This is done by operating on vertex-loops instead of face-loops.
Single threaded operation still loops over faces since iterating
over vertices adds some overhead in the case of custom-normals
as the order used for accessing loops must be the same as iterating
of a faces loops.
From isolated timing tests of bm_mesh_loops_calc_normals on high
poly models, this gives between 3.5x to 10x speedup,
with larger gains for meshes with custom-normals.
NOTE: this is part one of two patches for multi-threaded auto-smooth,
tagging edges as sharp is still single threaded.
Reviewed By: mont29
Ref D11928
|
|
While doxygen supports both, conform to our style guide.
Note that single back-tick's are already used in a majority of comments.
|
|
|
|
|
|
|
|
This shows the text as part of the assertion message.
|
|
Use more direct access to next/previous vertices.
- `BM_edge_other_vert(l_curr->e, l_curr->v)` -> `l_curr->next->v`.
- `BM_edge_other_vert(l_curr->prev->e, l_curr->v)` -> `l_curr->prev->v`.
Add asserts to keep the intention clear.
|
|
Only DNA_customdata_types.h is needed for BMEditMesh.
|
|
|
|
|
|
|
|
Reserve the term count for values that require calculation
(typically linked lists).
|
|
Using BMesh operators through the edit-mesh API created a full copy
of the mesh so it was possible to restore the mesh in case
one of the operators raised an error.
Remove support for automatic backup/restore from the EDBM_op_* API's
as it adds significant overhead and was rarely used.
Operators that need this can use the BMBackup API to backup & restore
the mesh in case of failure.
Add warning levels to BMO_error_raise so operators can report problems
without it being interpreted as a request to cancel the operation.
For high-poly meshes creating and freeing a full copy is an expensive
operation, removing this gives a speedup of ~1.77x for most operators
except for "connect_verts" / "connect_vert_pair"
which still uses this functionality.
|
|
Previously, any face groups that could not be merged into a face
caused the entire operation to report an error and do nothing.
Now these cases are skipped over, dissolving faces where possible.
|
|
- Only create arrays with groups of two or more faces.
- Remove raising exception for zero length arrays.
- Remove redundant exception check (assert there is no exception).
- Use a struct for face array & it's length instead of a NULL
terminated array (removes the need to count faces in a loop).
|
|
Also use doxy style function reference `#` prefix chars when
referencing identifiers.
|
|
|
|
|