1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
|
/**
******************************************************************************
* @file stm32f1xx_hal_pcd_ex.c
* @author MCD Application Team
* @brief PCD Extended HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the USB Peripheral Controller:
* + Extended features functions
*
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal.h"
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
/** @defgroup PCDEx PCDEx
* @brief PCD Extended HAL module driver
* @{
*/
#ifdef HAL_PCD_MODULE_ENABLED
#if defined (USB) || defined (USB_OTG_FS)
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup PCDEx_Exported_Functions PCDEx Exported Functions
* @{
*/
/** @defgroup PCDEx_Exported_Functions_Group1 Peripheral Control functions
* @brief PCDEx control functions
*
@verbatim
===============================================================================
##### Extended features functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Update FIFO configuration
@endverbatim
* @{
*/
#if defined (USB_OTG_FS)
/**
* @brief Set Tx FIFO
* @param hpcd PCD handle
* @param fifo The number of Tx fifo
* @param size Fifo size
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_SetTxFiFo(PCD_HandleTypeDef *hpcd, uint8_t fifo, uint16_t size)
{
uint8_t i;
uint32_t Tx_Offset;
/* TXn min size = 16 words. (n : Transmit FIFO index)
When a TxFIFO is not used, the Configuration should be as follows:
case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
--> Txm can use the space allocated for Txn.
case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
--> Txn should be configured with the minimum space of 16 words
The FIFO is used optimally when used TxFIFOs are allocated in the top
of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
When DMA is used 3n * FIFO locations should be reserved for internal DMA registers */
Tx_Offset = hpcd->Instance->GRXFSIZ;
if (fifo == 0U)
{
hpcd->Instance->DIEPTXF0_HNPTXFSIZ = ((uint32_t)size << 16) | Tx_Offset;
}
else
{
Tx_Offset += (hpcd->Instance->DIEPTXF0_HNPTXFSIZ) >> 16;
for (i = 0U; i < (fifo - 1U); i++)
{
Tx_Offset += (hpcd->Instance->DIEPTXF[i] >> 16);
}
/* Multiply Tx_Size by 2 to get higher performance */
hpcd->Instance->DIEPTXF[fifo - 1U] = ((uint32_t)size << 16) | Tx_Offset;
}
return HAL_OK;
}
/**
* @brief Set Rx FIFO
* @param hpcd PCD handle
* @param size Size of Rx fifo
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_SetRxFiFo(PCD_HandleTypeDef *hpcd, uint16_t size)
{
hpcd->Instance->GRXFSIZ = size;
return HAL_OK;
}
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
/**
* @brief Configure PMA for EP
* @param hpcd Device instance
* @param ep_addr endpoint address
* @param ep_kind endpoint Kind
* USB_SNG_BUF: Single Buffer used
* USB_DBL_BUF: Double Buffer used
* @param pmaadress: EP address in The PMA: In case of single buffer endpoint
* this parameter is 16-bit value providing the address
* in PMA allocated to endpoint.
* In case of double buffer endpoint this parameter
* is a 32-bit value providing the endpoint buffer 0 address
* in the LSB part of 32-bit value and endpoint buffer 1 address
* in the MSB part of 32-bit value.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_PMAConfig(PCD_HandleTypeDef *hpcd, uint16_t ep_addr,
uint16_t ep_kind, uint32_t pmaadress)
{
PCD_EPTypeDef *ep;
/* initialize ep structure*/
if ((0x80U & ep_addr) == 0x80U)
{
ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK];
}
else
{
ep = &hpcd->OUT_ep[ep_addr];
}
/* Here we check if the endpoint is single or double Buffer*/
if (ep_kind == PCD_SNG_BUF)
{
/* Single Buffer */
ep->doublebuffer = 0U;
/* Configure the PMA */
ep->pmaadress = (uint16_t)pmaadress;
}
else /* USB_DBL_BUF */
{
/* Double Buffer Endpoint */
ep->doublebuffer = 1U;
/* Configure the PMA */
ep->pmaaddr0 = (uint16_t)(pmaadress & 0xFFFFU);
ep->pmaaddr1 = (uint16_t)((pmaadress & 0xFFFF0000U) >> 16);
}
return HAL_OK;
}
/**
* @brief Software Device Connection,
* this function is not required by USB OTG FS peripheral, it is used
* only by USB Device FS peripheral.
* @param hpcd PCD handle
* @param state connection state (0 : disconnected / 1: connected)
* @retval None
*/
__weak void HAL_PCDEx_SetConnectionState(PCD_HandleTypeDef *hpcd, uint8_t state)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(state);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_PCDEx_SetConnectionState could be implemented in the user file
*/
}
#endif /* defined (USB) */
/**
* @brief Send LPM message to user layer callback.
* @param hpcd PCD handle
* @param msg LPM message
* @retval HAL status
*/
__weak void HAL_PCDEx_LPM_Callback(PCD_HandleTypeDef *hpcd, PCD_LPM_MsgTypeDef msg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(msg);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_PCDEx_LPM_Callback could be implemented in the user file
*/
}
/**
* @brief Send BatteryCharging message to user layer callback.
* @param hpcd PCD handle
* @param msg LPM message
* @retval HAL status
*/
__weak void HAL_PCDEx_BCD_Callback(PCD_HandleTypeDef *hpcd, PCD_BCD_MsgTypeDef msg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(msg);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_PCDEx_BCD_Callback could be implemented in the user file
*/
}
/**
* @}
*/
/**
* @}
*/
#endif /* defined (USB) || defined (USB_OTG_FS) */
#endif /* HAL_PCD_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
