Github: fix non zero return behavior in docker actions. Firmware: fix F6 build. (#886)

* Github: treat non 0 exit code as fatal
* GitHub: inject missing -e flag to bash in docker
* Firmware: sync targets

3 files changed, 11 insertions, 14 deletions

diff --git a/firmware/targets/f6/ble-glue/serial_service.h b/firmware/targets/f6/ble-glue/serial_service.h
index 1c365c0e..6e19f86d 100644
--- a/firmware/targets/f6/ble-glue/serial_service.h
+++ b/firmware/targets/f6/ble-glue/serial_service.h
@@ -4,6 +4,7 @@
 #include <stdbool.h>
 
 #define SERIAL_SVC_DATA_LEN_MAX (486)
+#define SERIAL_SVC_CHAR_VALUE_LEN_MAX (243)
 
 #ifdef __cplusplus
 extern "C" {
diff --git a/firmware/targets/f6/furi-hal/furi-hal-subghz.c b/firmware/targets/f6/furi-hal/furi-hal-subghz.c
index 85fe401e..3e810880 100644
--- a/firmware/targets/f6/furi-hal/furi-hal-subghz.c
+++ b/firmware/targets/f6/furi-hal/furi-hal-subghz.c
@@ -296,9 +296,9 @@ static const uint8_t furi_hal_subghz_preset_gfsk_9_99kb_async_regs[][2] = {
     {CC1101_IOCFG0, 0x06}, //GDO0 Output Pin Configuration
     {CC1101_FIFOTHR, 0x47}, //RX FIFO and TX FIFO Thresholds
 
-    //1 : CRC calculation in TX and CRC check in RX enabled,
+    //1 : CRC calculation in TX and CRC check in RX enabled, 
     //1 : Variable packet length mode. Packet length configured by the first byte after sync word
-    {CC1101_PKTCTRL0, 0x05},
+    {CC1101_PKTCTRL0,0x05}, 
 
     {CC1101_FSCTRL1, 0x06}, //Frequency Synthesizer Control
 
@@ -314,8 +314,8 @@ static const uint8_t furi_hal_subghz_preset_gfsk_9_99kb_async_regs[][2] = {
     {CC1101_DEVIATN, 0x34}, //Deviation = 19.042969
     {CC1101_MCSM0, 0x18}, //Main Radio Control State Machine Configuration
     {CC1101_FOCCFG, 0x16}, //Frequency Offset Compensation Configuration
-
-    {CC1101_AGCCTRL2, 0x43}, //AGC Control
+    
+    {CC1101_AGCCTRL2, 0x43 },   //AGC Control
     {CC1101_AGCCTRL1, 0x40},
     {CC1101_AGCCTRL0, 0x91},
 
@@ -392,8 +392,7 @@ void furi_hal_subghz_init() {
         ;
 
     // GD0 high
-    cc1101_write_reg(
-        &furi_hal_spi_bus_handle_subghz, CC1101_IOCFG0, CC1101IocfgHW | CC1101_IOCFG_INV);
+    cc1101_write_reg(&furi_hal_spi_bus_handle_subghz, CC1101_IOCFG0, CC1101IocfgHW | CC1101_IOCFG_INV);
     while(hal_gpio_read(&gpio_cc1101_g0) != true)
         ;
 
@@ -454,7 +453,7 @@ void furi_hal_subghz_load_preset(FuriHalSubGhzPreset preset) {
     } else if(preset == FuriHalSubGhzPresetGFSK9_99KbAsync) {
         furi_hal_subghz_load_registers(furi_hal_subghz_preset_gfsk_9_99kb_async_regs);
         furi_hal_subghz_load_patable(furi_hal_subghz_preset_gfsk_async_patable);
-    } else {
+    } else{
         furi_crash(NULL);
     }
 }
@@ -499,8 +498,7 @@ void furi_hal_subghz_flush_tx() {
 bool furi_hal_subghz_rx_pipe_not_empty() {
     CC1101RxBytes status[1];
     furi_hal_spi_acquire(&furi_hal_spi_bus_handle_subghz);
-    cc1101_read_reg(
-        &furi_hal_spi_bus_handle_subghz, (CC1101_STATUS_RXBYTES) | CC1101_BURST, (uint8_t*)status);
+    cc1101_read_reg(&furi_hal_spi_bus_handle_subghz, (CC1101_STATUS_RXBYTES) | CC1101_BURST, (uint8_t*)status);
     furi_hal_spi_release(&furi_hal_spi_bus_handle_subghz);
     // TODO: you can add a buffer overflow flag if needed
     if(status->NUM_RXBYTES > 0) {
@@ -674,15 +672,13 @@ void furi_hal_subghz_set_path(FuriHalSubGhzPath path) {
     furi_hal_spi_acquire(&furi_hal_spi_bus_handle_subghz);
     if(path == FuriHalSubGhzPath433) {
         hal_gpio_write(&gpio_rf_sw_0, 0);
-        cc1101_write_reg(
-            &furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW | CC1101_IOCFG_INV);
+        cc1101_write_reg(&furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW | CC1101_IOCFG_INV);
     } else if(path == FuriHalSubGhzPath315) {
         hal_gpio_write(&gpio_rf_sw_0, 1);
         cc1101_write_reg(&furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW);
     } else if(path == FuriHalSubGhzPath868) {
         hal_gpio_write(&gpio_rf_sw_0, 1);
-        cc1101_write_reg(
-            &furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW | CC1101_IOCFG_INV);
+        cc1101_write_reg(&furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW | CC1101_IOCFG_INV);
     } else if(path == FuriHalSubGhzPathIsolate) {
         hal_gpio_write(&gpio_rf_sw_0, 0);
         cc1101_write_reg(&furi_hal_spi_bus_handle_subghz, CC1101_IOCFG2, CC1101IocfgHW);
diff --git a/firmware/targets/f6/furi-hal/furi-hal-uart.h b/firmware/targets/f6/furi-hal/furi-hal-uart.h
index f245c484..53a45f1e 100644
--- a/firmware/targets/f6/furi-hal/furi-hal-uart.h
+++ b/firmware/targets/f6/furi-hal/furi-hal-uart.h
@@ -74,4 +74,4 @@ void furi_hal_uart_set_irq_cb(
 
 #ifdef __cplusplus
 }
-#endif
+#endif
\ No newline at end of file