diff options
Diffstat (limited to 'Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h')
| -rw-r--r-- | Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h | 59 |
1 files changed, 55 insertions, 4 deletions
diff --git a/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h b/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h index 65f48cc62..308c1d143 100644 --- a/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h +++ b/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.h @@ -50,6 +50,7 @@ extern "C" { ERR_BLE_INIT = 0, ERR_THREAD_LLD_FATAL_ERROR = 125, /* The LLD driver used on 802_15_4 detected a fatal error */ ERR_THREAD_UNKNOWN_CMD = 126, /* The command send by the M4 to control the Thread stack is unknown */ + ERR_ZIGBEE_UNKNOWN_CMD = 200, /* The command send by the M4 to control the Zigbee stack is unknown */ } SCHI_SystemErrCode_t; #define SHCI_EVTCODE ( 0xFF ) @@ -135,7 +136,8 @@ extern "C" { SHCI_OCF_C2_MAC_802_15_4_INIT, SHCI_OCF_C2_REINIT, SHCI_OCF_C2_ZIGBEE_INIT, - SHCI_OCF_C2_LLD_TESTS_INIT + SHCI_OCF_C2_LLD_TESTS_INIT, + SHCI_OCF_C2_EXTPA_CONFIG } SHCI_OCF_t; #define SHCI_OPCODE_C2_FUS_GET_STATE (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_GET_STATE) @@ -325,6 +327,7 @@ extern "C" { { BLE_ENABLE, THREAD_ENABLE, + ZIGBEE_ENABLE, } SHCI_C2_CONCURRENT_Mode_Param_t; /** No response parameters*/ @@ -335,18 +338,42 @@ extern "C" { { BLE_IP, THREAD_IP, + ZIGBEE_IP, } SHCI_C2_FLASH_Ip_t; /** No response parameters*/ -#define SHCI_OPCODE_C2_RADIO_ALLOW_LOW_POWER (( SHCI_OGF << 10) + SHCI_OCF_C2_RADIO_ALLOW_LOW_POWER) +#define SHCI_OPCODE_C2_RADIO_ALLOW_LOW_POWER (( SHCI_OGF << 10) + SHCI_OCF_C2_RADIO_ALLOW_LOW_POWER) #define SHCI_OPCODE_C2_MAC_802_15_4_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_MAC_802_15_4_INIT) #define SHCI_OPCODE_C2_REINIT (( SHCI_OGF << 10) + SHCI_OCF_C2_REINIT) -#define SHCI_OPCODE_C2_ZIGBEE_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_ZIGBEE_INIT) +#define SHCI_OPCODE_C2_ZIGBEE_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_ZIGBEE_INIT) -#define SHCI_OPCODE_C2_LLD_TESTS_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_LLD_TESTS_INIT) +#define SHCI_OPCODE_C2_LLD_TESTS_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_LLD_TESTS_INIT) + +#define SHCI_OPCODE_C2_EXTPA_CONFIG (( SHCI_OGF << 10) + SHCI_OCF_C2_EXTPA_CONFIG) + /** Command parameters */ + enum + { + EXT_PA_ENABLED_LOW, + EXT_PA_ENABLED_HIGH, + }/* gpio_polarity */; + + enum + { + EXT_PA_DISABLED, + EXT_PA_ENABLED, + }/* gpio_status */; + + typedef PACKED_STRUCT{ + uint32_t gpio_port; + uint16_t gpio_pin_number; + uint8_t gpio_polarity; + uint8_t gpio_status; + } SHCI_C2_EXTPA_CONFIG_Cmd_Param_t; + + /** No response parameters*/ /* Exported type --------------------------------------------------------*/ @@ -408,6 +435,9 @@ typedef MB_WirelessFwInfoTable_t SHCI_WirelessFwInfoTable_t; #define INFO_STACK_TYPE_MAC 0x40 #define INFO_STACK_TYPE_BLE_THREAD_FTD_STATIC 0x50 #define INFO_STACK_TYPE_802154_LLD_TESTS 0x60 +#define INFO_STACK_TYPE_802154_PHY_VALID 0x61 +#define INFO_STACK_TYPE_BLE_PHY_VALID 0x62 +#define INFO_STACK_TYPE_BLE_ZIGBEE_FFD_STATIC 0x70 typedef struct { /** @@ -656,6 +686,27 @@ typedef struct { */ SHCI_CmdStatus_t SHCI_C2_Reinit( void ); + /** + * SHCI_C2_ExtpaConfig + * @brief Send the Ext PA configuration + * When the CPU2 receives the command, it controls the Ext PA as requested by the configuration + * This configures only which IO is used to enable/disable the ExtPA and the associated polarity + * This command has no effect on the other IO that is used to control the mode of the Ext PA (Rx/Tx) + * + * @param gpio_port: GPIOx where x can be (A..F) to select the GPIO peripheral for STM32WBxx family + * @param gpio_pin_number: This parameter can be one of GPIO_PIN_x (= LL_GPIO_PIN_x) where x can be (0..15). + * @param gpio_polarity: This parameter can be either + * - EXT_PA_ENABLED_LOW: ExtPA is enabled when GPIO is low + * - EXT_PA_ENABLED_HIGH: ExtPA is enabled when GPIO is high + * @param gpio_status: This parameter can be either + * - EXT_PA_DISABLED: Stop driving the ExtPA + * - EXT_PA_ENABLED: Drive the ExtPA according to radio activity + * (ON before the Event and OFF at the end of the event) + * @retval Status + */ + SHCI_CmdStatus_t SHCI_C2_ExtpaConfig(uint32_t gpio_port, uint16_t gpio_pin_number, uint8_t gpio_polarity, uint8_t gpio_status); + + #ifdef __cplusplus } #endif |