diff options
Diffstat (limited to 'Projects/NUCLEO-WB35CE/Examples_MIX/PWR/PWR_STOP1/readme.txt')
-rw-r--r-- | Projects/NUCLEO-WB35CE/Examples_MIX/PWR/PWR_STOP1/readme.txt | 101 |
1 files changed, 101 insertions, 0 deletions
diff --git a/Projects/NUCLEO-WB35CE/Examples_MIX/PWR/PWR_STOP1/readme.txt b/Projects/NUCLEO-WB35CE/Examples_MIX/PWR/PWR_STOP1/readme.txt new file mode 100644 index 000000000..3d190dbe0 --- /dev/null +++ b/Projects/NUCLEO-WB35CE/Examples_MIX/PWR/PWR_STOP1/readme.txt @@ -0,0 +1,101 @@ +/** + @page PWR_STOP1 PWR Example + + @verbatim + ****************************************************************************** + * @file Examples_MIX/PWR/PWR_STOP1/readme.txt + * @author MCD Application Team + * @brief Description of the PWR_STOP1 example. + ****************************************************************************** + * + * Copyright (c) 2019 STMicroelectronics. All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + @endverbatim + +@par Example Description + +How to enter the STOP 1 mode and wake up from this mode by using external +reset or wakeup interrupt (all the RCC function calls use RCC LL API +for minimizing footprint and maximizing performance). + +In the associated software, the system clock is set to 64 MHz, an EXTI line +is connected to the user button through PA.0 and configured to generate an +interrupt on falling edge upon key press. +The SysTick is programmed to generate an interrupt each 1 ms and in the SysTick +interrupt handler, LED2 is toggled in order to indicate whether the MCU is in STOP 1 mode +or RUN mode. + +5 seconds after start-up, the system automatically enters STOP 1 mode and +LED2 stops toggling. + +The User push-button (SW1) can be pressed at any time to wake-up the system. +The software then comes back in RUN mode for 5 sec. before automatically entering STOP 1 mode again. + +Two leds LED2 and LED1 are used to monitor the system state as following: + - LED2 toggling: system in RUN mode + - LED2 off : system in STOP 1 mode + - LED2 and LED1 ON: configuration failed (system will go to an infinite loop) + +These steps are repeated in an infinite loop. + +@note To measure MCU current consumption on board STM32WB Nucleo, + board configuration must be applied: + - remove all jumpers on connector JP5 to avoid leakages between ST-Link circuitry and STM32WB device. + - remove jumper JP2 and connect an amperemeter to measure current between the 2 connectors of JP2. + +@note This example can not be used in DEBUG mode due to the fact + that the Cortex-M4 core is no longer clocked during low power mode + so debugging features are disabled. + +@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds) + based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from + a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower) + than the peripheral interrupt. Otherwise the caller ISR process will be blocked. + To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function. + +@note The application needs to ensure that the SysTick time base is always set to 1 millisecond + to have correct HAL operation. + +@par Keywords + +Power, PWR, stop mode, wake-up, external reset, Interrupt, low power mode + +@par Directory contents + + - Examples_MIX/PWR/PWR_STOP1/Inc/stm32wbxx_conf.h HAL Configuration file + - Examples_MIX/PWR/PWR_STOP1/Inc/stm32wbxx_it.h Header for stm32wbxx_it.c + - Examples_MIX/PWR/PWR_STOP1/Inc/main.h Header file for main.c + - Examples_MIX/PWR/PWR_STOP1/Src/system_stm32wbxx.c STM32WBxx system clock configuration file + - Examples_MIX/PWR/PWR_STOP1/Src/stm32wbxx_it.c Interrupt handlers + - Examples_MIX/PWR/PWR_STOP1/Src/main.c Main program + - Examples_MIX/PWR/PWR_STOP1/Src/stm32wbxx_hal_msp.c HAL MSP module + +@par Hardware and Software environment + + - This example runs on STM32WBxx devices + + + - This example has been tested with STMicroelectronics NUCLEO-WB35CE + board and can be easily tailored to any other supported device + and development board. + + - NUCLEO-WB35CE set-up: + - Use LED2 and LED1 connected respectively to PB.00 and PB.05 pins + - User push-button (SW1) connected to pin PA.00 (External line 0) + +@par How to use it ? + +In order to make the program work, you must do the following : + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + + + * <h3><center>© COPYRIGHT STMicroelectronics</center></h3> + */ |