diff options
Diffstat (limited to 'Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h')
| -rw-r--r-- | Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h | 36 |
1 files changed, 19 insertions, 17 deletions
diff --git a/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h b/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h index bd949bad9..e9527fae1 100644 --- a/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h +++ b/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE/BLE_MultiAppAt/Core/Inc/hw_conf.h @@ -1,13 +1,13 @@ /* USER CODE BEGIN Header */ /** ****************************************************************************** - * File Name : hw_conf.h - * Description : Hardware configuration file for BLE - * middleWare. + * @file hw_conf.h + * @author MCD Application Team + * @brief Configuration of hardware interface ****************************************************************************** * @attention * - * <h2><center>© Copyright (c) 2019 STMicroelectronics. + * <h2><center>© Copyright (c) 2019 STMicroelectronics. * All rights reserved.</center></h2> * * This software component is licensed by ST under Ultimate Liberty license @@ -24,14 +24,16 @@ #define HW_CONF_H /****************************************************************************** -* Semaphores -* THIS SHALL NO BE CHANGED AS THESE SEMAPHORES ARE USED AS WELL ON THE CM0+ -*****************************************************************************/ + * Semaphores + * THIS SHALL NO BE CHANGED AS THESE SEMAPHORES ARE USED AS WELL ON THE CM0+ + *****************************************************************************/ /** * Index of the semaphore used by CPU2 to prevent the CPU1 to either write or erase data in flash * The CPU1 shall not either write or erase in flash when this semaphore is taken by the CPU2 * When the CPU1 needs to either write or erase in flash, it shall first get the semaphore and release it just * after writing a raw (64bits data) or erasing one sector. +* Once the Semaphore has been released, there shall be at least 1us before it can be taken again. This is required +* to give the opportunity to CPU2 to take it. * On v1.4.0 and older CPU2 wireless firmware, this semaphore is unused and CPU2 is using PES bit. * By default, CPU2 is using the PES bit to protect its timing. The CPU1 may request the CPU2 to use the semaphore * instead of the PES bit by sending the system command SHCI_C2_SetFlashActivityControl() @@ -134,10 +136,10 @@ *****************************************************************************/ #define CFG_HW_LPUART1_ENABLED 1 -#define CFG_HW_LPUART1_DMA_TX_SUPPORTED 0 +#define CFG_HW_LPUART1_DMA_TX_SUPPORTED 1 -#define CFG_HW_USART1_ENABLED 0 -#define CFG_HW_USART1_DMA_TX_SUPPORTED 0 +#define CFG_HW_USART1_ENABLED 1 +#define CFG_HW_USART1_DMA_TX_SUPPORTED 1 /** * LPUART1 @@ -148,7 +150,7 @@ /** < The application shall check the selected source clock is enable */ #define CFG_HW_LPUART1_SOURCE_CLOCK RCC_LPUART1CLKSOURCE_SYSCLK -#define CFG_HW_LPUART1_BAUDRATE 9600 +#define CFG_HW_LPUART1_BAUDRATE 115200 #define CFG_HW_LPUART1_WORDLENGTH UART_WORDLENGTH_8B #define CFG_HW_LPUART1_STOPBITS UART_STOPBITS_1 #define CFG_HW_LPUART1_PARITY UART_PARITY_NONE @@ -187,9 +189,9 @@ #define CFG_HW_LPUART1_DMAMUX_CLK_ENABLE __HAL_RCC_DMAMUX1_CLK_ENABLE #define CFG_HW_LPUART1_DMA_CLK_ENABLE __HAL_RCC_DMA1_CLK_ENABLE #define CFG_HW_LPUART1_TX_DMA_REQ DMA_REQUEST_LPUART1_TX -#define CFG_HW_LPUART1_TX_DMA_CHANNEL DMA1_CHANNEL_4 -#define CFG_HW_LPUART1_TX_DMA_IRQn DMA1_CHANNEL_4_IRQn -#define CFG_HW_LPUART1_DMA_TX_IRQHandler DMA1_CHANNEL_4_IRQHandler +#define CFG_HW_LPUART1_TX_DMA_CHANNEL DMA1_Channel4 +#define CFG_HW_LPUART1_TX_DMA_IRQn DMA1_Channel4_IRQn +#define CFG_HW_LPUART1_DMA_TX_IRQHandler DMA1_Channel4_IRQHandler /** * UART1 @@ -239,9 +241,9 @@ #define CFG_HW_USART1_DMAMUX_CLK_ENABLE __HAL_RCC_DMAMUX1_CLK_ENABLE #define CFG_HW_USART1_DMA_CLK_ENABLE __HAL_RCC_DMA2_CLK_ENABLE #define CFG_HW_USART1_TX_DMA_REQ DMA_REQUEST_USART1_TX -#define CFG_HW_USART1_TX_DMA_CHANNEL DMA2_CHANNEL_4 -#define CFG_HW_USART1_TX_DMA_IRQn DMA2_CHANNEL_4_IRQn -#define CFG_HW_USART1_DMA_TX_IRQHandler DMA2_CHANNEL_4_IRQHandler +#define CFG_HW_USART1_TX_DMA_CHANNEL DMA2_Channel4 +#define CFG_HW_USART1_TX_DMA_IRQn DMA2_Channel4_IRQn +#define CFG_HW_USART1_DMA_TX_IRQHandler DMA2_Channel4_IRQHandler #endif /*HW_CONF_H */ |