diff options
Diffstat (limited to 'Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE_Zigbee/BLE_Zigbee_Dyn/Core/Inc/hw_conf.h')
| -rw-r--r-- | Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE_Zigbee/BLE_Zigbee_Dyn/Core/Inc/hw_conf.h | 221 |
1 files changed, 221 insertions, 0 deletions
diff --git a/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE_Zigbee/BLE_Zigbee_Dyn/Core/Inc/hw_conf.h b/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE_Zigbee/BLE_Zigbee_Dyn/Core/Inc/hw_conf.h new file mode 100644 index 000000000..b76dd2494 --- /dev/null +++ b/Projects/P-NUCLEO-WB55.Nucleo/Applications/BLE_Zigbee/BLE_Zigbee_Dyn/Core/Inc/hw_conf.h @@ -0,0 +1,221 @@ +/** + ****************************************************************************** + * @file hw_conf.h + * @author MCD Application Team + * @brief Configuration of hardware interface + ****************************************************************************** + * @attention + * + * <h2><center>© Copyright (c) 2019 STMicroelectronics. + * All rights reserved.</center></h2> + * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ + + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __HW_CONF_H +#define __HW_CONF_H + +/****************************************************************************** + * Semaphores + * THIS SHALL NO BE CHANGED AS THESE SEMAPHORES ARE USED AS WELL ON THE CM0+ + *****************************************************************************/ +/* Index of the semaphore used to manage the entry Stop Mode procedure */ +#define CFG_HW_ENTRY_STOP_MODE_SEMID 4 + +/* Index of the semaphore used to access the RCC */ +#define CFG_HW_RCC_SEMID 3 + +/* Index of the semaphore used to access the FLASH */ +#define CFG_HW_FLASH_SEMID 2 + +/* Index of the semaphore used to access the PKA */ +#define CFG_HW_PKA_SEMID 1 + +/* Index of the semaphore used to access the RNG */ +#define CFG_HW_RNG_SEMID 0 + + +/****************************************************************************** + * HW TIMER SERVER + *****************************************************************************/ +/** + * The user may define the maximum number of virtual timers supported. + * It shall not exceed 255 + */ +#define CFG_HW_TS_MAX_NBR_CONCURRENT_TIMER 6 + +/** + * The user may define the priority in the NVIC of the RTC_WKUP interrupt handler that is used to manage the + * wakeup timer. + * This setting is the preemptpriority part of the NVIC. + */ +#define CFG_HW_TS_NVIC_RTC_WAKEUP_IT_PREEMPTPRIO 3 + +/** + * The user may define the priority in the NVIC of the RTC_WKUP interrupt handler that is used to manage the + * wakeup timer. + * This setting is the subpriority part of the NVIC. It does not exist on all processors. When it is not supported + * on the CPU, the setting is ignored + */ +#define CFG_HW_TS_NVIC_RTC_WAKEUP_IT_SUBPRIO 0 + +/** + * Define a critical section in the Timer server + * The Timer server does not support the API to be nested + * The Application shall either: + * a) Ensure this will never happen + * b) Define the critical section + * The default implementations is masking all interrupts using the PRIMASK bit + * The TimerServer driver uses critical sections to avoid context corruption. This is achieved with the macro + * TIMER_ENTER_CRITICAL_SECTION and TIMER_EXIT_CRITICAL_SECTION. When CFG_HW_TS_USE_PRIMASK_AS_CRITICAL_SECTION is set + * to 1, all STM32 interrupts are masked with the PRIMASK bit of the CortexM CPU. It is possible to use the BASEPRI + * register of the CortexM CPU to keep allowed some interrupts with high priority. In that case, the user shall + * re-implement TIMER_ENTER_CRITICAL_SECTION and TIMER_EXIT_CRITICAL_SECTION and shall make sure that no TimerServer + * API are called when the TIMER critical section is entered + */ +#define CFG_HW_TS_USE_PRIMASK_AS_CRITICAL_SECTION 1 + +/** + * This value shall reflect the maximum delay there could be in the application between the time the RTC interrupt + * is generated by the Hardware and the time when the RTC interrupt handler is called. This time is measured in + * number of RTCCLK ticks. + * A relaxed timing would be 10ms + * When the value is too short, the timerserver will not be able to count properly and all timeout may be random. + * When the value is too long, the device may wake up more often than the most optimal configuration. However, the + * impact on power consumption would be marginal (unless the value selected is extremely too long). It is strongly + * recommended to select a value large enough to make sure it is not too short to ensure reliability of the system + * as this will have marginal impact on low power mode + */ +#define CFG_HW_TS_RTC_HANDLER_MAX_DELAY ( 10 * (LSI_VALUE/1000) ) + +/** + * Interrupt ID in the NVIC of the RTC Wakeup interrupt handler + * It shall be type of IRQn_Type + */ +#define CFG_HW_TS_RTC_WAKEUP_HANDLER_ID RTC_WKUP_IRQn + + +/****************************************************************************** + * HW UART + *****************************************************************************/ +/* For release: set to 1 CFG_HW_LPUART1_ENABLED and CFG_HW_LPUART1_DMA_TX_SUPPORTED */ +#define CFG_HW_LPUART1_ENABLED 1 +#define CFG_HW_LPUART1_DMA_TX_SUPPORTED 1 + +#define CFG_HW_USART1_ENABLED 1 +#define CFG_HW_USART1_DMA_TX_SUPPORTED 1 + +/** + * LPUART1 + */ +#define CFG_HW_LPUART1_PREEMPTPRIORITY 0x0F +#define CFG_HW_LPUART1_SUBPRIORITY 0 + +/** < The application shall check the selected source clock is enable */ +#define CFG_HW_LPUART1_SOURCE_CLOCK RCC_LPUART1CLKSOURCE_SYSCLK + +#define CFG_HW_LPUART1_BAUDRATE 115200 +#define CFG_HW_LPUART1_WORDLENGTH UART_WORDLENGTH_8B +#define CFG_HW_LPUART1_STOPBITS UART_STOPBITS_1 +#define CFG_HW_LPUART1_PARITY UART_PARITY_NONE +#define CFG_HW_LPUART1_HWFLOWCTL UART_HWCONTROL_NONE +#define CFG_HW_LPUART1_MODE UART_MODE_TX_RX +#define CFG_HW_LPUART1_ADVFEATUREINIT UART_ADVFEATURE_NO_INIT +#define CFG_HW_LPUART1_OVERSAMPLING UART_OVERSAMPLING_8 + +#define CFG_HW_LPUART1_TX_PORT_CLK_ENABLE __HAL_RCC_GPIOA_CLK_ENABLE +#define CFG_HW_LPUART1_TX_PORT GPIOA +#define CFG_HW_LPUART1_TX_PIN GPIO_PIN_2 +#define CFG_HW_LPUART1_TX_MODE GPIO_MODE_AF_PP +#define CFG_HW_LPUART1_TX_PULL GPIO_NOPULL +#define CFG_HW_LPUART1_TX_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_LPUART1_TX_ALTERNATE GPIO_AF8_LPUART1 + +#define CFG_HW_LPUART1_RX_PORT_CLK_ENABLE __HAL_RCC_GPIOA_CLK_ENABLE +#define CFG_HW_LPUART1_RX_PORT GPIOA +#define CFG_HW_LPUART1_RX_PIN GPIO_PIN_3 +#define CFG_HW_LPUART1_RX_MODE GPIO_MODE_AF_PP +#define CFG_HW_LPUART1_RX_PULL GPIO_NOPULL +#define CFG_HW_LPUART1_RX_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_LPUART1_RX_ALTERNATE GPIO_AF8_LPUART1 + +#define CFG_HW_LPUART1_CTS_PORT_CLK_ENABLE __HAL_RCC_GPIOA_CLK_ENABLE +#define CFG_HW_LPUART1_CTS_PORT GPIOA +#define CFG_HW_LPUART1_CTS_PIN GPIO_PIN_6 +#define CFG_HW_LPUART1_CTS_MODE GPIO_MODE_AF_PP +#define CFG_HW_LPUART1_CTS_PULL GPIO_PULLDOWN +#define CFG_HW_LPUART1_CTS_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_LPUART1_CTS_ALTERNATE GPIO_AF8_LPUART1 + +#define CFG_HW_LPUART1_DMA_TX_PREEMPTPRIORITY 0x0F +#define CFG_HW_LPUART1_DMA_TX_SUBPRIORITY 0 + +#define CFG_HW_LPUART1_DMAMUX_CLK_ENABLE __HAL_RCC_DMAMUX1_CLK_ENABLE +#define CFG_HW_LPUART1_DMA_CLK_ENABLE __HAL_RCC_DMA1_CLK_ENABLE +#define CFG_HW_LPUART1_TX_DMA_REQ DMA_REQUEST_LPUART1_TX +#define CFG_HW_LPUART1_TX_DMA_CHANNEL DMA1_Channel4 +#define CFG_HW_LPUART1_TX_DMA_IRQn DMA1_Channel4_IRQn +#define CFG_HW_LPUART1_DMA_TX_IRQHandler DMA1_Channel4_IRQHandler + +/** + * UART1 + */ +#define CFG_HW_USART1_PREEMPTPRIORITY 0x0F +#define CFG_HW_USART1_SUBPRIORITY 0 + +/** < The application shall check the selected source clock is enable */ +#define CFG_HW_USART1_SOURCE_CLOCK RCC_USART1CLKSOURCE_SYSCLK + +#define CFG_HW_USART1_BAUDRATE 115200 +#define CFG_HW_USART1_WORDLENGTH UART_WORDLENGTH_8B +#define CFG_HW_USART1_STOPBITS UART_STOPBITS_1 +#define CFG_HW_USART1_PARITY UART_PARITY_NONE +#define CFG_HW_USART1_HWFLOWCTL UART_HWCONTROL_NONE +#define CFG_HW_USART1_MODE UART_MODE_TX_RX +#define CFG_HW_USART1_ADVFEATUREINIT UART_ADVFEATURE_NO_INIT +#define CFG_HW_USART1_OVERSAMPLING UART_OVERSAMPLING_8 + +#define CFG_HW_USART1_TX_PORT_CLK_ENABLE __HAL_RCC_GPIOB_CLK_ENABLE +#define CFG_HW_USART1_TX_PORT GPIOB +#define CFG_HW_USART1_TX_PIN GPIO_PIN_6 +#define CFG_HW_USART1_TX_MODE GPIO_MODE_AF_PP +#define CFG_HW_USART1_TX_PULL GPIO_NOPULL +#define CFG_HW_USART1_TX_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_USART1_TX_ALTERNATE GPIO_AF7_USART1 + +#define CFG_HW_USART1_RX_PORT_CLK_ENABLE __HAL_RCC_GPIOB_CLK_ENABLE +#define CFG_HW_USART1_RX_PORT GPIOB +#define CFG_HW_USART1_RX_PIN GPIO_PIN_7 +#define CFG_HW_USART1_RX_MODE GPIO_MODE_AF_PP +#define CFG_HW_USART1_RX_PULL GPIO_NOPULL +#define CFG_HW_USART1_RX_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_USART1_RX_ALTERNATE GPIO_AF7_USART1 + +#define CFG_HW_USART1_CTS_PORT_CLK_ENABLE __HAL_RCC_GPIOA_CLK_ENABLE +#define CFG_HW_USART1_CTS_PORT GPIOA +#define CFG_HW_USART1_CTS_PIN GPIO_PIN_11 +#define CFG_HW_USART1_CTS_MODE GPIO_MODE_AF_PP +#define CFG_HW_USART1_CTS_PULL GPIO_PULLDOWN +#define CFG_HW_USART1_CTS_SPEED GPIO_SPEED_FREQ_VERY_HIGH +#define CFG_HW_USART1_CTS_ALTERNATE GPIO_AF7_USART1 + +#define CFG_HW_USART1_DMA_TX_PREEMPTPRIORITY 0x0F +#define CFG_HW_USART1_DMA_TX_SUBPRIORITY 0 + +#define CFG_HW_USART1_DMAMUX_CLK_ENABLE __HAL_RCC_DMAMUX1_CLK_ENABLE +#define CFG_HW_USART1_DMA_CLK_ENABLE __HAL_RCC_DMA2_CLK_ENABLE +#define CFG_HW_USART1_TX_DMA_REQ DMA_REQUEST_USART1_TX +#define CFG_HW_USART1_TX_DMA_CHANNEL DMA2_Channel4 +#define CFG_HW_USART1_TX_DMA_IRQn DMA2_Channel4_IRQn +#define CFG_HW_USART1_DMA_TX_IRQHandler DMA2_Channel4_IRQHandler + +#endif /*__HW_CONF_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |