diff options
Diffstat (limited to 'Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h')
| -rw-r--r-- | Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h | 75 |
1 files changed, 0 insertions, 75 deletions
diff --git a/Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h b/Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h index a5e0e1075..a229ec666 100644 --- a/Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h +++ b/Projects/P-NUCLEO-WB55.USBDongle/Applications/BLE/BLE_MeshLightingDemo/STM32_WPAN/app/PWM_config.h @@ -13,7 +13,6 @@ * INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. *******************************************************************************/ -//#include "BlueNRG1_mft.h" #include "mesh_cfg_usr.h" /* Macros defined for the number of PWM Provided */ @@ -23,80 +22,6 @@ #define PWM3 3 #define PWM4 4 -/* Setting for the Hardware PWM selection for BlueNRG-1 & BlueNRG-2 board. -if user want to change the hardware pwm according to his application then user -can select the given settings. - - SERIAL1_MODE SERIAL2_MODE -PWM0_PIN GPIO_2 GPIO_4 -PWM1_PIN GPIO_3 GPIO_5 -*/ - -/*STEVAL_BlueNRG-1 - *STEVAL_BlueNRG-2 - * This configuration given below is for the BlueNRG-1 and BlueNRG-2 board. - * Here user has selected the PWM0 in SERIAL2_MODE and PWM1 in SERIAL1_MODE. - * User can configure software PWM to any of the GPIO which are not used for - * hardware PWM. -*/ -/* PWM pins for MFT1 and MFT2 respectively */ -#if defined STEVAL_BLUENRG_1_BOARD_PWM_SELECTION || defined STEVAL_BLUENRG_2_BOARD_PWM_SELECTION - -#define PWM0_PIN GPIO_Pin_4 -#define PWM1_PIN GPIO_Pin_3 - -/* GPIOs pins (SOFTWARE PWM) used to output a PWM signal */ -#define PWM2_PIN GPIO_Pin_1 -#define PWM3_PIN GPIO_Pin_2 -#define PWM4_PIN GPIO_Pin_14 /*Blue Led*/ -#endif -/**************************************************************************/ - -/* CUSTOM BOARD SETTING - * Uncomment the macros given below for custom board and comment the above macros - * which are given for BlueNRG board. - * This configuration given below is for the custom board. - * Here user has selected the PWM0 in SERIAL2_MODE and PWM1 in SERIAL2_MODE. - * User can configure software PWM to any of the GPIO which are not used for - * hardware PWM. -NOTE - Do not enable the sensor model with this configuration.As GPIO_4 is used - for sensor already. -*/ -/* PWM pins for MFT1 and MFT2 respectively */ -#ifdef CUSTOM_BOARD_PWM_SELECTION - -#define PWM0_PIN GPIO_Pin_4 -#define PWM1_PIN GPIO_Pin_5 - -/* GPIOs pins (SOFTWARE PWM) used to output a PWM signal */ -#define PWM2_PIN GPIO_Pin_0 /* Red Led*/ -#define PWM3_PIN GPIO_Pin_2 /*Green Led*/ -#define PWM4_PIN GPIO_Pin_3 /*Blue Led*/ - -#endif -/*************************************************************************/ - -/* - * STEVAL-BLUEMIC-1 - * This configuration given below is for the BlueNRG-1 and BlueNRG-2 board. - * Here user has selected the PWM0 in SERIAL2_MODE and PWM1 in SERIAL1_MODE. - * User can configure software PWM to any of the GPIO which are not used for - * hardware PWM. -NOTE - Do not enable the sensor model with this configuration.As GPIO_4 is used - for sensor already. -*/ -/* PWM pins for MFT1 and MFT2 respectively */ -#ifdef STEVAL_BLUEMIC_1_BOARD_PWM_SELECTION - -#define PWM0_PIN GPIO_Pin_4 -#define PWM1_PIN GPIO_Pin_3 //blue_led - -/* GPIOs pins (SOFTWARE PWM) used to output a PWM signal */ -#define PWM2_PIN GPIO_Pin_8 -#define PWM3_PIN GPIO_Pin_6 -#define PWM4_PIN GPIO_Pin_14 - -#endif /************************************************************************/ /*STM32WB |