1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
|
/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file app_conf.h
* @author MCD Application Team
* @brief Application configuration file for STM32WPAN Middleware.
******************************************************************************
* @attention
*
* Copyright (c) 2020-2021 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* USER CODE END Header */
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef APP_CONF_H
#define APP_CONF_H
#include "hw.h"
#include "hw_conf.h"
#include "hw_if.h"
#include "ble_bufsize.h"
/******************************************************************************
* Application Config
******************************************************************************/
/**< generic parameters ******************************************************/
/**
* Define Tx Power
*/
#define CFG_TX_POWER (0x18) /* -0.15dBm */
/**
* Radio activity event
*/
#define CFG_RADIO_ACTIVITY_EVENT_MASK (0x0006) /**< 0x0000 default */
/**
* Define Advertising parameters
*/
#define CFG_FAST_CONN_ADV_INTERVAL_MIN (0x00C8) /**< 250ms */
#define CFG_FAST_CONN_ADV_INTERVAL_MAX (0x00C8) /**< 250ms */
#define CFG_LP_CONN_ADV_INTERVAL_MIN (0x0640) /**< 1s */
#define CFG_LP_CONN_ADV_INTERVAL_MAX (0x0FA0) /**< 2.5s */
/******************************************************************************
* BLE Stack
******************************************************************************/
/**
* Maximum number of simultaneous connections that the device will support.
* Valid values are from 1 to 8
*/
#define CFG_BLE_NUM_LINK 2
/**
* Maximum number of Services that can be stored in the GATT database.
* Note that the GAP and GATT services are automatically added so this parameter should be 2 plus the number of user services
*/
#define CFG_BLE_NUM_GATT_SERVICES 8
/**
* Maximum number of Attributes
* (i.e. the number of characteristic + the number of characteristic values + the number of descriptors, excluding the services)
* that can be stored in the GATT database.
* Note that certain characteristics and relative descriptors are added automatically during device initialization
* so this parameters should be 9 plus the number of user Attributes
*/
#define CFG_BLE_NUM_GATT_ATTRIBUTES 68
/**
* Maximum supported ATT_MTU size
* This parameter is ignored by the CPU2 when CFG_BLE_OPTIONS is set to 1"
*/
#define CFG_BLE_MAX_ATT_MTU (156)
/**
* Size of the storage area for Attribute values
* This value depends on the number of attributes used by application. In particular the sum of the following quantities (in octets) should be made for each attribute:
* - attribute value length
* - 5, if UUID is 16 bit; 19, if UUID is 128 bit
* - 2, if server configuration descriptor is used
* - 2*DTM_NUM_LINK, if client configuration descriptor is used
* - 2, if extended properties is used
* The total amount of memory needed is the sum of the above quantities for each attribute.
* This parameter is ignored by the CPU2 when CFG_BLE_OPTIONS is set to 1"
*/
#define CFG_BLE_ATT_VALUE_ARRAY_SIZE (1344)
/**
* Prepare Write List size in terms of number of packet
* This parameter is ignored by the CPU2 when CFG_BLE_OPTIONS is set to 1"
*/
#define CFG_BLE_PREPARE_WRITE_LIST_SIZE BLE_PREP_WRITE_X_ATT(CFG_BLE_MAX_ATT_MTU)
/**
* Number of allocated memory blocks
* This parameter is overwritten by the CPU2 with an hardcoded optimal value when the parameter when CFG_BLE_OPTIONS is set to 1
*/
#define CFG_BLE_MBLOCK_COUNT (BLE_MBLOCKS_CALC(CFG_BLE_PREPARE_WRITE_LIST_SIZE, CFG_BLE_MAX_ATT_MTU, CFG_BLE_NUM_LINK))
/**
* Enable or disable the Extended Packet length feature. Valid values are 0 or 1.
*/
#define CFG_BLE_DATA_LENGTH_EXTENSION 1
/**
* Sleep clock accuracy in Slave mode (ppm value)
*/
#define CFG_BLE_SLAVE_SCA 500
/**
* Sleep clock accuracy in Master mode
* 0 : 251 ppm to 500 ppm
* 1 : 151 ppm to 250 ppm
* 2 : 101 ppm to 150 ppm
* 3 : 76 ppm to 100 ppm
* 4 : 51 ppm to 75 ppm
* 5 : 31 ppm to 50 ppm
* 6 : 21 ppm to 30 ppm
* 7 : 0 ppm to 20 ppm
*/
#define CFG_BLE_MASTER_SCA 0
/**
* Source for the low speed clock for RF wake-up
* 1 : external high speed crystal HSE/32/32
* 0 : external low speed crystal ( no calibration )
*/
#define CFG_BLE_LSE_SOURCE 0
/**
* Start up time of the high speed (16 or 32 MHz) crystal oscillator in units of 625/256 us (~2.44 us)
*/
#define CFG_BLE_HSE_STARTUP_TIME 0x148
/**
* Maximum duration of the connection event when the device is in Slave mode in units of 625/256 us (~2.44 us)
*/
#define CFG_BLE_MAX_CONN_EVENT_LENGTH (0xFFFFFFFF)
/**
* Viterbi Mode
* 1 : enabled
* 0 : disabled
*/
#define CFG_BLE_VITERBI_MODE 1
/**
* BLE stack Options flags to be configured with:
* - SHCI_C2_BLE_INIT_OPTIONS_LL_ONLY
* - SHCI_C2_BLE_INIT_OPTIONS_LL_HOST
* - SHCI_C2_BLE_INIT_OPTIONS_NO_SVC_CHANGE_DESC
* - SHCI_C2_BLE_INIT_OPTIONS_WITH_SVC_CHANGE_DESC
* - SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RO
* - SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RW
* - SHCI_C2_BLE_INIT_OPTIONS_EXT_ADV
* - SHCI_C2_BLE_INIT_OPTIONS_NO_EXT_ADV
* - SHCI_C2_BLE_INIT_OPTIONS_CS_ALGO2
* - SHCI_C2_BLE_INIT_OPTIONS_NO_CS_ALGO2
* - SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_1
* - SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_2_3
* which are used to set following configuration bits:
* (bit 0): 1: LL only
* 0: LL + host
* (bit 1): 1: no service change desc.
* 0: with service change desc.
* (bit 2): 1: device name Read-Only
* 0: device name R/W
* (bit 3): 1: extended advertizing supported [NOT SUPPORTED]
* 0: extended advertizing not supported [NOT SUPPORTED]
* (bit 4): 1: CS Algo #2 supported
* 0: CS Algo #2 not supported
* (bit 7): 1: LE Power Class 1
* 0: LE Power Class 2-3
* other bits: reserved (shall be set to 0)
*/
#define CFG_BLE_OPTIONS (SHCI_C2_BLE_INIT_OPTIONS_LL_HOST | SHCI_C2_BLE_INIT_OPTIONS_WITH_SVC_CHANGE_DESC | SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RW | SHCI_C2_BLE_INIT_OPTIONS_NO_EXT_ADV | SHCI_C2_BLE_INIT_OPTIONS_NO_CS_ALGO2 | SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_2_3)
#define CFG_BLE_MAX_COC_INITIATOR_NBR (32)
#define CFG_BLE_MIN_TX_POWER (0)
#define CFG_BLE_MAX_TX_POWER (0)
/**
* BLE Rx model configuration flags to be configured with:
* - SHCI_C2_BLE_INIT_RX_MODEL_AGC_RSSI_LEGACY
* - SHCI_C2_BLE_INIT_RX_MODEL_AGC_RSSI_BLOCKER
* which are used to set following configuration bits:
* (bit 0): 1: agc_rssi model improved vs RF blockers
* 0: Legacy agc_rssi model
* other bits: reserved (shall be set to 0)
*/
#define CFG_BLE_RX_MODEL_CONFIG SHCI_C2_BLE_INIT_RX_MODEL_AGC_RSSI_LEGACY
/******************************************************************************
* Transport Layer
******************************************************************************/
/**
* Queue length of BLE Event
* This parameter defines the number of asynchronous events that can be stored in the HCI layer before
* being reported to the application. When a command is sent to the BLE core coprocessor, the HCI layer
* is waiting for the event with the Num_HCI_Command_Packets set to 1. The receive queue shall be large
* enough to store all asynchronous events received in between.
* When CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE is set to 27, this allow to store three 255 bytes long asynchronous events
* between the HCI command and its event.
* This parameter depends on the value given to CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE. When the queue size is to small,
* the system may hang if the queue is full with asynchronous events and the HCI layer is still waiting
* for a CC/CS event, In that case, the notification TL_BLE_HCI_ToNot() is called to indicate
* to the application a HCI command did not receive its command event within 30s (Default HCI Timeout).
*/
#define CFG_TLBLE_EVT_QUEUE_LENGTH 5
/**
* This parameter should be set to fit most events received by the HCI layer. It defines the buffer size of each element
* allocated in the queue of received events and can be used to optimize the amount of RAM allocated by the Memory Manager.
* It should not exceed 255 which is the maximum HCI packet payload size (a greater value is a lost of memory as it will
* never be used)
* It shall be at least 4 to receive the command status event in one frame.
* The default value is set to 27 to allow receiving an event of MTU size in a single buffer. This value maybe reduced
* further depending on the application.
*
*/
#define CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE 255 /**< Set to 255 with the memory manager and the mailbox */
#define TL_BLE_EVENT_FRAME_SIZE ( TL_EVT_HDR_SIZE + CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE )
/******************************************************************************
* Debug
******************************************************************************/
/**
* When set, this resets some hw resources to set the device in the same state than the power up
* The FW resets only register that may prevent the FW to run properly
*
* This shall be set to 0 in a final product
*
*/
#define CFG_HW_RESET_BY_FW 1
/**
* keep debugger enabled while in any low power mode when set to 1
* should be set to 0 in production
*/
#define CFG_DEBUGGER_SUPPORTED 1
/******************************************************************************
* OTP manager
******************************************************************************/
#define CFG_OTP_BASE_ADDRESS OTP_AREA_BASE
#define CFG_OTP_END_ADRESS OTP_AREA_END_ADDR
#endif /*APP_CONF_H */
|
