blob: 1e44351319b0a05c91ca8e11bb0263cc0209ad60 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/**
******************************************************************************
* @file app_conf.h
* @author MCD Application Team
* @brief Application configuration file
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under Ultimate Liberty license
* SLA0044, the "License"; You may not use this file except in compliance with
* the License. You may obtain a copy of the License at:
* www.st.com/SLA0044
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef APP_CONF_H
#define APP_CONF_H
#include "hw.h"
#include "hw_conf.h"
#include "hw_if.h"
/******************************************************************************
* Debug
******************************************************************************/
/**
* When set, this resets some hw resources to set the device in the same state than the power up
* The FW resets only register that may prevent the FW to run properly
*
* This shall be set to 0 in a final product
*
*/
#define CFG_HW_RESET_BY_FW 0x01
#define CFG_LED_SUPPORTED 0x00
#define CFG_LED_TRACE_LPM 0x00
#define CFG_LED_TRACE_LPTIMER 0x00
/**
* keep debugger enabled while in any low power mode when set to 1
* should be set to 0 in production
*/
#define CFG_DEBUGGER_SUPPORTED 0
/******************************************************************************
* LOW POWER
******************************************************************************/
/**
* Supported requester to the MCU Low Power Manager - can be increased up to 32
* It lits a bit mapping of all user of the Low Power Manager
*/
typedef enum
{
/* USER CODE BEGIN CFG_LPM_Id_t */
CFG_INIT_TASK = 0x00,
CFG_DATA_EMITER_TASK = 0x01
/* USER CODE END CFG_LPM_Id_t */
} CFG_LPM_Id_t;
/*****************************************************************************/
/******************************************************************************
* Transport Layer
******************************************************************************/
/**
* Queue length of BLE Event
* This parameter defines the number of asynchronous events that can be stored in the HCI layer before
* being reported to the application. When a command is sent to the BLE core coprocessor, the HCI layer
* is waiting for the event with the Num_HCI_Command_Packets set to 1. The receive queue shall be large
* enough to store all asynchronous events received in between.
* When CFG_TL_MOST_EVENT_PAYLOAD_SIZE is set to 27, this allow to store three 255 bytes long asynchronous events
* between the HCI command and its event.
* This parameter depends on the value given to CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE. When the queue size is to small,
* the system may hang if the queue is full with asynchronous events and the HCI layer is still waiting
* for a CC/CS event, In that case, the notification TL_BLE_HCI_ToNot() is called to indicate
* to the application a HCI command did not receive its command event within 30s (Default HCI Timeout).
*/
#define CFG_TL_EVT_QUEUE_LENGTH 5
/**
* This parameter should be set to fit most events received by the HCI layer. It defines the buffer size of each element
* allocated in the queue of received events and can be used to optimize the amount of RAM allocated by the Memory Manager.
* It should not exceed 255 which is the maximum HCI packet payload size (a greater value is a lost of memory as it will
* never be used)
* It shall be at least 4 to receive the command status event in one frame.
* The default value is set to 27 to allow receiving an event of MTU size in a single buffer. This value maybe reduced
* further depending on the application.
*
*/
#define CFG_TL_MOST_EVENT_PAYLOAD_SIZE 255 /**< Set to 255 with the memory manager and the mailbox */
#define TL_EVENT_FRAME_SIZE ( TL_EVT_HDR_SIZE + CFG_TL_MOST_EVENT_PAYLOAD_SIZE )
/******************************************************************************
* LPTimer #1 Config
******************************************************************************/
extern LPTIM_HandleTypeDef hlptim1;
/* Set the Maximum value of the counter (Auto-Reload) that defines the Period */
#define PERIOD (uint32_t) (32768 - 1)
/* Set the Timeout value */
#define TIMEOUT (uint32_t) (32768 - 1)
/* USER CODE END Private defines */
/******************************************************************************
* OTP manager
******************************************************************************/
#define CFG_OTP_BASE_ADDRESS OTP_AREA_BASE
#define CFG_OTP_END_ADRESS OTP_AREA_END_ADDR
#endif /* APP_CONF_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
