1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
/**
******************************************************************************
* @file app_conf.h
* @author MCD Application Team
* @brief Application configuration file
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under Ultimate Liberty license
* SLA0044, the "License"; You may not use this file except in compliance with
* the License. You may obtain a copy of the License at:
* www.st.com/SLA0044
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef APP_CONF_H
#define APP_CONF_H
#include "hw.h"
#include "hw_conf.h"
/******************************************************************************
* Debug
******************************************************************************/
/**
* When set, this resets some hw resources to set the device in the same state than the power up
* The FW resets only register that may prevent the FW to run properly
*
* This shall be set to 0 in a final product
*
*/
#define CFG_HW_RESET_BY_FW 1
#define CFG_LED_SUPPORTED 1
/**
* keep debugger enabled while in any low power mode when set to 1
* should be set to 0 in production
*/
#define CFG_DEBUGGER_SUPPORTED 1
/*****************************************************************************
* Traces
* Enable or Disable traces in application
* When CFG_DEBUG_TRACE is set, traces are activated
*
* Note : Refer to utilities_conf.h file in order to details
* the level of traces : CFG_DEBUG_TRACE_FULL or CFG_DEBUG_TRACE_LIGHT
*****************************************************************************/
#define CFG_DEBUG_TRACE 1
/**
* When CFG_DEBUG_TRACE_FULL is set to 1, the trace are output with the API name, the file name and the line number
* When CFG_DEBUG_TRACE_LIGHT is set to 1, only the debug message is output
*
* When both are set to 0, no trace are output
* When both are set to 1, CFG_DEBUG_TRACE_FULL is selected
*/
#define CFG_DEBUG_TRACE_LIGHT 1
#define CFG_DEBUG_TRACE_FULL 0
#if (( CFG_DEBUG_TRACE != 0 ) && ( CFG_DEBUG_TRACE_LIGHT == 0 ) && (CFG_DEBUG_TRACE_FULL == 0))
#undef CFG_DEBUG_TRACE_FULL
#undef CFG_DEBUG_TRACE_LIGHT
#define CFG_DEBUG_TRACE_FULL 0
#define CFG_DEBUG_TRACE_LIGHT 1
#endif
#if ( CFG_DEBUG_TRACE == 0 )
#undef CFG_DEBUG_TRACE_FULL
#undef CFG_DEBUG_TRACE_LIGHT
#define CFG_DEBUG_TRACE_FULL 0
#define CFG_DEBUG_TRACE_LIGHT 0
#endif
/**
* When not set, the traces is looping on sending the trace over UART
*/
#define DBG_TRACE_USE_CIRCULAR_QUEUE 1
/**
* max buffer Size to queue data traces and max data trace allowed.
* Only Used if DBG_TRACE_USE_CIRCULAR_QUEUE is defined
*/
#define DBG_TRACE_MSG_QUEUE_SIZE 4096
#define MAX_DBG_TRACE_MSG_SIZE 1024
/******************************************************************************
* Configure Log level for Application
******************************************************************************/
#define APPLI_CONFIG_LOG_LEVEL LOG_LEVEL_INFO
#define APPLI_PRINT_FILE_FUNC_LINE 0
/******************************************************************************
* UART interfaces
******************************************************************************/
#define CFG_DEBUG_TRACE_UART hw_lpuart1
#define CFG_CLI_UART hw_uart1
/******************************************************************************
* Transport Layer
******************************************************************************/
/**
* Queue length of BLE Event
* This parameter defines the number of asynchronous events that can be stored in the HCI layer before
* being reported to the application. When a command is sent to the BLE core coprocessor, the HCI layer
* is waiting for the event with the Num_HCI_Command_Packets set to 1. The receive queue shall be large
* enough to store all asynchronous events received in between.
* When CFG_TL_MOST_EVENT_PAYLOAD_SIZE is set to 27, this allow to store three 255 bytes long asynchronous events
* between the HCI command and its event.
* This parameter depends on the value given to CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE. When the queue size is to small,
* the system may hang if the queue is full with asynchronous events and the HCI layer is still waiting
* for a CC/CS event, In that case, the notification TL_BLE_HCI_ToNot() is called to indicate
* to the application a HCI command did not receive its command event within 30s (Default HCI Timeout).
*/
#define CFG_TL_EVT_QUEUE_LENGTH 5
/**
* This parameter should be set to fit most events received by the HCI layer. It defines the buffer size of each element
* allocated in the queue of received events and can be used to optimize the amount of RAM allocated by the Memory Manager.
* It should not exceed 255 which is the maximum HCI packet payload size (a greater value is a lost of memory as it will
* never be used)
* It shall be at least 4 to receive the command status event in one frame.
* The default value is set to 27 to allow receiving an event of MTU size in a single buffer. This value maybe reduced
* further depending on the application.
*
*/
#define CFG_TL_MOST_EVENT_PAYLOAD_SIZE 255 /**< Set to 255 with the memory manager and the mailbox */
#define TL_EVENT_FRAME_SIZE ( TL_EVT_HDR_SIZE + CFG_TL_MOST_EVENT_PAYLOAD_SIZE )
/******************************************************************************
* OTP manager
******************************************************************************/
#define CFG_OTP_BASE_ADDRESS OTP_AREA_BASE
#define CFG_OTP_END_ADRESS OTP_AREA_END_ADDR
#endif /* APP_CONF_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
