blob: 1c2de614ccc18ee9adc83ef0a71d66b7a0dfb9a4 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
/**
@page Zigbee_MeterId_Client_Router application
@verbatim
******************************************************************************
* @file Zigbee/Zigbee_MeterId_Client_Router/readme.txt
* @author MCD Application Team
* @brief Description of the Zigbee Meter Identification Cluster application as a client
* using a centralized network.
******************************************************************************
*
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under Ultimate Liberty license
* SLA0044, the "License"; You may not use this file except in compliance with
* the License. You may obtain a copy of the License at:
* www.st.com/SLA0044
*
******************************************************************************
@endverbatim
@par Application Description
How to use Meter Identification cluster as a client on a centralized Zigbee network.
The purpose of this application is to show how to create a Zigbee centralized network, and
how to communicate from one node to another one using the Meter Identification cluster. Once the Zigbee mesh
network is created, the user can send requests from the client to the server through push buttons SW1 and SW2.
For this application it is requested to have:
- 1 STM32WB55xx (Nucleo or USB dongle) board loaded with:
- wireless coprocessor : stm32wb5x_Zigbee_FFD_fw.bin
- application : Zigbee_MeterId_Server_Coord
- 1 or more STM32WB55xx board loaded with:
- wireless coprocessor : stm32wb5x_Zigbee_FFD_fw.bin
- application : Zigbee_MeterId_Client_Router
Demo use case :
This demo shows how to use Meter Identification cluster.
The Meter Identification Server set up its read-only attributes (read-only attributes local write allowed).
The Meter Identification Client can remotely read them by requesting a remote read.
Two read-only attributes are used :
- the Company Name (ZCL string)
- the Meter Type ID (16-bit integer)
Device 1 Device 2
+--------+ +--------+
| | | |
| Client | -->| Server |
| | ZbZclAttrStringWriteShort(ZCL_METER_ID_ATTR_COMPANY_NAME) | | |
| | ---| |
| | | |
| | -->| |
| | ZbZclAttrStringWriteShort(ZCL_METER_ID_ATTR_METER_TYPE_ID) | | |
| | ---| |
| | | |
| | ZbZclReadReq(ZCL_METER_ID_ATTR_COMPANY_NAME) | |
PushB SW1=>| | -------------------------------------------------------------------> | |
| | <------------------------------------------------------------------- | |
| | | |
| | ZbZclReadReq(ZCL_METER_ID_ATTR_METER_TYPE_ID) | |
PushB SW2=>| | -------------------------------------------------------------------> | |
| | <------------------------------------------------------------------- | |
| | | |
+--------+ +--------+
To setup the application :
a) Open the project, build it and load your generated application on your STM32WB devices.
To run the application :
a) Start the first board. It must be the coordinator of the Zigbee network so in this demo application it is
the device running Zigbee_MeterId_Server_Coord application (Device2 in the above diagram).
Wait for the Blue LED (LED1) ON.
Start the second board. This board is configured as Zigbee router and will be attached to the network created
by the coordinator. Do the same for the other boards if applicable.
b) At this stage, the Zigbee network is automatically created and BLUE LED (LED1) is ON on all devices.
it is now possible to remotely read Meter Identification server attributes on the client by pressing on
the SW1/SW2 push button.
Note: when LED1, LED2 and LED3 are toggling it is indicating an error has occurred on application.
@par Keywords
Zigbee
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- For the Zigbee_MeterId_Server_Coord application, a STM32WB55xx USB dongle can be used.
- This example has been tested with an STMicroelectronics STM32WB55RG_Nucleo
board and can be easily tailored to any other supported device
and development board.
- On STM32WB55RG_Nucleo, the jumpers must be configured as described
in this section. Starting from the top left position up to the bottom
right position, the jumpers on the Board must be set as follows:
CN11: GND [OFF]
JP4: VDDRF [ON]
JP6: VC0 [ON]
JP2: +3V3 [ON]
JP1: USB_STL [ON] All others [OFF]
CN12: GND [OFF]
CN7: <All> [OFF]
JP3: VDD_MCU [ON]
JP5: GND [OFF] All others [ON]
CN10: <All> [OFF]
@par How to use it ?
=> Loading of the stm32wb5x_Zigbee_FFD_fw.bin binary
This application requests having the stm32wb5x_Zigbee_FFD_fw.bin binary flashed on the Wireless Coprocessor.
If it is not the case, you need to use STM32CubeProgrammer to load the appropriate binary.
All available binaries are located under /Projects/STM32_Copro_Wireless_Binaries directory.
Refer to UM2237 to learn how to use/install STM32CubeProgrammer.
Refer to /Projects/STM32_Copro_Wireless_Binaries/ReleaseNote.html for the detailed procedure to change the
Wireless Coprocessor binary.
=> Getting traces
To get the traces you need to connect your Board to the Hyperterminal (through the STLink Virtual COM Port).
The UART must be configured as follows:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- Stop Bit = 1 bit
- Parity = none
- Flow control = none
=> Running the application
Refer to the Application description at the beginning of this readme.txt
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|