1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
/**
@page ADC_SingleConversion_TriggerSW_IT ADC example
@verbatim
******************************************************************************
* @file Examples/ADC/ADC_SingleConversion_TriggerSW_IT/readme.txt
* @author MCD Application Team
* @brief Description of the ADC_SingleConversion_TriggerSW_IT example.
******************************************************************************
*
* Copyright (c) 2019 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
How to use the ADC to convert a single channel at each software start. This example
uses the interrupt programming model.
Example configuration:
ADC is configured to convert a single channel, in single conversion mode,
from SW trigger.
ADC interruption enabled: EOC (end of conversion of ADC group regular).
Example execution:
The ADC performs 1 conversion of the selected channel. When conversion is completed,
ADC interruption occurs. IRQ handler callback function reads conversion data from
ADC data register and stores it into a variable, LED2 is turned on.
For debug: variables to monitor with debugger watch window:
- "uhADCxConvertedData": ADC group regular conversion data
- "uhADCxConvertedData_Voltage_mVolt": ADC conversion data computation to physical values
Connection needed:
None.
Note: Optionally, a voltage can be supplied to the analog input pin (cf pin below),
between 0V and Vdda=3.3V, to perform a ADC conversion on a determined
voltage level.
Otherwise, this pin can be let floating (in this case ADC conversion data
will be undetermined).
Other peripherals used:
1 GPIO for LED
1 GPIO for analog input: PA1 (Arduino connector CN10 pin A2, Morpho connector CN9 pin 32)
Board settings:
- ADC is configured to convert ADC_CHANNEL_6 (Arduino connector CN10 pin A2, Morpho connector CN9 pin 32).
- The voltage input on ADC channel must be provided by an external source connected to Arduino connector CN10 pin A2, Morpho connector CN9 pin 32.
To observe voltage level applied on ADC channel through GPIO, connect a voltmeter on
pin PA1 (Arduino connector CN10 pin A2, Morpho connector CN9 pin 32).
P-NUCLEO-WB55 board LED is be used to monitor the program execution status:
- Normal operation: LED2 is turned-on/off in function of ADC conversion
result.
- "On" upon conversion completion
- "Off" during conversion
- Error: In case of error, LED2 is toggling at a frequency of 1Hz.
@par Keywords
ADC, analog digital converter, analog, conversion, voltage, channel, analog input, trigger
@par Directory contents
- ADC/ADC_SingleConversion_TriggerSW_IT/Inc/stm32wbxx_hal_conf.h HAL configuration file
- ADC/ADC_SingleConversion_TriggerSW_IT/Inc/stm32wbxx_it.h Interrupt handlers header file
- ADC/ADC_SingleConversion_TriggerSW_IT/Inc/main.h Header for main.c module
- ADC/ADC_SingleConversion_TriggerSW_IT/Src/stm32wbxx_it.c Interrupt handlers
- ADC/ADC_SingleConversion_TriggerSW_IT/Src/main.c Main program
- ADC/ADC_SingleConversion_TriggerSW_IT/Src/stm32wbxx_hal_msp.c HAL MSP module
- ADC/ADC_SingleConversion_TriggerSW_IT/Src/system_stm32wbxx.c STM32WBxx system source file
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- This example has been tested with P-NUCLEO-WB55 board and can be
easily tailored to any other supported device and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
|
