1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
/**
@page TIM_DMA TIM DMA example
@verbatim
******************************************************************************
* @file TIM/TIM_DMA/readme.txt
* @author MCD Application Team
* @brief Description of the TIM DMA example.
******************************************************************************
*
* Copyright (c) 2019 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
Use of the DMA with TIMER Update request
to transfer data from memory to TIMER Capture Compare Register 3 (TIMx_CCR3).
The following configuration values are used in this example:
- TIM1CLK = SystemCoreClock
- Counter repetition = 3
- Prescaler = 0
- TIM1 counter clock = SystemCoreClock
- SystemCoreClock is set to 64 MHz for STM32WBxx
The objective is to configure TIM1 channel 3 to generate complementary PWM
(Pulse Width Modulation) signal with a frequency equal to 17.57 KHz, and a variable
duty cycle that is changed by the DMA after a specific number of Update DMA request.
The number of this repetitive requests is defined by the TIM1 Repetition counter,
each 4 Update Requests, the TIM1 Channel 3 Duty Cycle changes to the next new
value defined by the aCCValue_Buffer.
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
The SystemClock_Config() function is used to configure the system clock for STM32WB55RGVx Devices :
The CPU at 64 MHz
The PWM waveform can be displayed using an oscilloscope.
In nominal mode (except at start) , it should looks like this :
. . . . . . . . . . . . . . . . . .
___________ _______ ___ ___________ __
_| |___| |_______| |___________| |__|
<----57us -----><----57us -----><----57us -----><----57us ----->
@note PWM signal frequency value mentioned above is theoretical (obtained when the system clock frequency
is exactly 64 MHz). Since the generated system clock frequency may vary from one board to another observed
PWM signal frequency might be slightly different.
@note Care must be taken when using HAL_Delay(), this function provides accurate
delay (in milliseconds) based on variable incremented in SysTick ISR. This
implies that if HAL_Delay() is called from a peripheral ISR process, then
the SysTick interrupt must have higher priority (numerically lower)
@note This example needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Timer, DMA, PWM, Frequency, Duty Cycle, Waveform, Oscilloscope, Output, Signal
@par Directory contents
- TIM/TIM_DMA/Inc/stm32wbxx_hal_conf.h HAL configuration file
- TIM/TIM_DMA/Inc/stm32wbxx_it.h Interrupt handlers header file
- TIM/TIM_DMA/Inc/main.h Header for main.c module
- TIM/TIM_DMA/Src/stm32wbxx_it.c Interrupt handlers
- TIM/TIM_DMA/Src/main.c Main program
- TIM/TIM_DMA/Src/stm32wbxx_hal_msp.c HAL MSP file
- TIM/TIM_DMA/Src/system_stm32wbxx.c STM32WBxx system source file
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- In this example, the clock is set to 64 MHz.
- This example has been tested with STMicroelectronics P-NUCLEO-WB55
board and can be easily tailored to any other supported device
and development board.
- P-NUCLEO-WB55 Set-up
- Connect the TIM1 pin to an oscilloscope to monitor the different waveforms:
- TIM1 CH3 (PA.10 (pin 31 in CN10 connector))
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
|
