1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
|
/**
@page UART_HyperTerminal_DMA UART Hyperterminal DMA Example
@verbatim
******************************************************************************
* @file UART/UART_HyperTerminal_DMA/readme.txt
* @author MCD Application Team
* @brief Description of the UART Hyperterminal example.
******************************************************************************
*
* Copyright (c) 2019 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
UART transmission (transmit/receive) in DMA mode
between a board and an HyperTerminal PC application.
Board: P-NUCLEO-WB55 (embeds a STM32WB55RG device)
Tx Pin: PB6
Rx Pin: PB7
_________________________
| ______________| _______________
| |USART | | HyperTerminal |
| | | | |
| | TX |______________________|RX |
| | | | |
| | | RS232 Cable | |
| | | | |
| | RX |______________________|TX |
| | | | |
| |______________| |_______________|
| |
| |
| |
| |
|_STM32_Board_____________|
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 64 MHz for STM32WBxx Devices.
The UART peripheral configuration is ensured by the HAL_UART_Init() function.
This later is calling the HAL_UART_MspInit()function which core is implementing
the configuration of the needed UART resources according to the used hardware (CLOCK,
GPIO, DMA and NVIC). You may update this function to change UART configuration.
The UART/Hyperterminal communication is then initiated.
The HAL_UART_Receive_DMA() and the HAL_UART_Transmit_DMA() functions allow respectively
the reception of Data from Hyperterminal and the transmission of a predefined data
buffer.
The Asynchronous communication aspect of the UART is clearly highlighted as the
data buffers transmission/reception to/from Hyperterminal are done simultaneously.
For this example the TxBuffer(aTxStartMessage) is predefined and the RxBuffer (aRxBuffer)
size is limited to 10 data by the mean of the RXBUFFERSIZE define in the main.c file.
In a first step the received data will be stored in the RxBuffer buffer and the
TxBuffer buffer content will be displayed in the Hyperterminal interface.
In a second step the received data in the RxBuffer buffer will be sent back to
Hyperterminal and displayed.
The end of this two steps are monitored through the HAL_UART_GetState() function
result.
P-NUCLEO-WB55 board LEDs are used to monitor the transfer status:
- LED2 turns ON if transmission/reception is complete and OK.
- LED3 turns ON when when there is an error in transmission/reception process.
The UART is configured as follows:
- BaudRate = 9600 baud
- Word Length = 8 Bits (7 data bit + 1 parity bit)
- One Stop Bit
- Odd parity
- Hardware flow control disabled (RTS and CTS signals)
- Reception and transmission are enabled in the time
@note USARTx/UARTx instance used and associated resources can be updated in "main.h"
file depending hardware configuration used.
@note When the parity is enabled, the computed parity is inserted at the MSB
position of the transmitted data.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Connectivity, UART, Printf, Baud rate, RS-232, HyperTerminal, full-duplex, HyperTerminal, DMA,
Transmission, Reception, Asynchronous
@par Directory contents
- UART/UART_HyperTerminal_DMA/Inc/stm32wbxx_hal_conf.h HAL configuration file
- UART/UART_HyperTerminal_DMA/Inc/stm32wbxx_it.h DMA interrupt handlers header file
- UART/UART_HyperTerminal_DMA/Inc/main.h Header for main.c module
- UART/UART_HyperTerminal_DMA/Src/stm32wbxx_it.c DMA interrupt handlers
- UART/UART_HyperTerminal_DMA/Src/main.c Main program
- UART/UART_HyperTerminal_DMA/Src/stm32wbxx_hal_msp.c HAL MSP module
- UART/UART_HyperTerminal_DMA/Src/system_stm32wbxx.c STM32WBxx system source file
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- This example has been tested with P-NUCLEO-WB55 board and can be
easily tailored to any other supported device and development board.
- P-NUCLEO-WB55 Set-up
- Connect USART1 TX (PB.06 (Pin 34 in CN10)) to RX pin of PC serial port (or USB to UART adapter)
and USART1 RX (PB.07 (Pin 6 in CN10)) to TX pin of PC serial port (or USB to UART adapter).
- Hyperterminal configuration:
- Data Length = 7 Bits
- One Stop Bit
- Odd parity
- BaudRate = 9600 baud
- Flow control: None
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
|