1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
/**
@page LPUART_WakeUpFromStop2_Init LPUART example
@verbatim
******************************************************************************
* @file Examples_LL/LPUART/LPUART_WakeUpFromStop2_Init/readme.txt
* @author MCD Application Team
* @brief Description of the LPUART_WakeUpFromStop2_Init LPUART example.
******************************************************************************
*
* Copyright (c) 2019 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
Configuration of GPIO and LPUART peripherals to allow characters
received on LPUART_RX pin to wake up the MCU from low-power mode. This example is based
on the LPUART LL API. The peripheral initialization uses LL
initialization function to demonstrate LL init usage.
LPUART Peripheral is configured in asynchronous mode (9600 bauds, 8 data bit, 1 start bit, 1 stop bit, no parity).
No HW flow control is used.
LPUART Clock is based on HSI.
Example execution:
After startup from reset and system configuration, LED2 is blinking quickly during 3 sec,
then MCU enters "Stop 2" mode (LED2 off).
On first character reception by the LPUART from PC Com port (ex: using HyperTerminal)
after "Stop 2" Mode period, MCU wakes up from "Stop 2" Mode.
Received character value is checked :
- On a specific value ('S' or 's'), LED2 is turned On and program ends.
- If different from 'S' or 's', program performs a quick LED2 blinks during 3 sec and
enters again "Stop 2" mode, waiting for next character to wake up.
In case of errors, LED2 is slowly blinking (1 sec period).
@par Keywords
Connectivity, LPUART, baud rate, RS-232, HyperTerminal, full-duplex,
Transmitter, Receiver, Asynchronous, Low Power, Wake Up
@par Directory contents
- LPUART/LPUART_WakeUpFromStop2_Init/Inc/stm32wbxx_it.h Interrupt handlers header file
- LPUART/LPUART_WakeUpFromStop2_Init/Inc/main.h Header for main.c module
- LPUART/LPUART_WakeUpFromStop2_Init/Inc/stm32_assert.h Template file to include assert_failed function
- LPUART/LPUART_WakeUpFromStop2_Init/Src/stm32wbxx_it.c Interrupt handlers
- LPUART/LPUART_WakeUpFromStop2_Init/Src/main.c Main program
- LPUART/LPUART_WakeUpFromStop2_Init/Src/system_stm32wbxx.c STM32WBxx system source file
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- This example has been tested with P-NUCLEO-WB55 board and can be
easily tailored to any other supported device and development board.
- P-NUCLEO-WB55 Set-up
- Connect STM32 MCU board LPUART1 TX pin (GPIO PC1 connected to pin 30 of CN7 connector)
to PC COM port RX signal
- Connect STM32 MCU board LPUART1 RX pin (GPIO PC0 connected to pin 28 of CN7 connector)
to PC COM port TX signal
- Connect STM32 MCU board GND to PC COM port GND signal
- Launch serial communication SW on PC (as HyperTerminal or TeraTerm) with proper configuration
(9600 bauds, 8 bits data, 1 stop bit, no parity, no HW flow control).
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
|
