1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
/**
@page PWR_OptimizedRunMode PWR standby example
@verbatim
******************************************************************************
* @file Examples_LL/PWR/PWR_OptimizedRunMode/readme.txt
* @author MCD Application Team
* @brief Description of the PWR Optimized Run Mode example.
******************************************************************************
*
* Copyright (c) 2019-2021 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to increase/decrease frequency and VCORE and how to enter/exit the
Low-power run mode.
In the associated software, the system clock is set to 64 MHz, an EXTI line
is connected to the User push-button (SW1) through PC.04 and configured to generate an
interrupt on falling edge upon key press.
After start-up LED2 is toggling FAST(100-ms blinking period), indicates that device
is running at 64MHz.
LED2 toggling speed is controlled by variable "uhLedBlinkSpeed".
The User push-button (SW1) can be pressed at any time to change Frequency, VCore(VOS)
and Low Power Run mode.
Initial STATE:
--> Freq: 64MHz, VCore 1.2V, Core in Run Mode
--> LED2 toggling FAST (100ms) - wait User push-button (SW1) action
STATE 2:
User push-button (SW1) pressed:
--> Freq: 16MHz, VCore 1.0V, Core in Run Mode
--> LED2 toggling MEDIUM (200ms) - wait User push-button (SW1) action
STATE 3:
User push-button (SW1) pressed:
--> Freq: 100KHz, VCore 1.0V, Core in Low Power Run Mode
--> LED2 toggling SLOW (400ms) - wait User push-button (SW1) action
STATE 4:
User push-button (SW1) pressed:
--> Freq: 16MHz, VCore 1.0V, Core in Run Mode
--> LED2 toggling MEDIUM (200ms) - wait User push-button (SW1) action
Final STATE:
User push-button (SW1) pressed:
--> Freq: 64MHz, VCore 1.2V, Core in Run Mode
--> LED2 toggling FAST (100ms) in infinite loop
@note To measure MCU current consumption on board STM32WB Nucleo,
board configuration must be applied:
- remove all jumpers on connector JP5 to avoid leakages between ST-Link circuitry and STM32WB device.
- remove jumper JP2 and connect an amperemeter to measure current between the 2 connectors of JP2.
NB: LED2 have an impact on power consumption.
Remove LED2 blinking to have a stable power consumption,
comment line "#define USE_LED" in main.c file
@par Keywords
Power, PWR, Low-power run mode, Interrupt, VCORE, Low Power
@par Directory contents
- PWR/PWR_OptimizedRunMode/Inc/stm32wbxx_it.h Interrupt handlers header file
- PWR/PWR_OptimizedRunMode/Inc/main.h Header for main.c module
- PWR/PWR_OptimizedRunMode/Inc/stm32_assert.h Template file to include assert_failed function
- PWR/PWR_OptimizedRunMode/Src/stm32wbxx_it.c Interrupt handlers
- PWR/PWR_OptimizedRunMode/Src/main.c Main program
- PWR/PWR_OptimizedRunMode/Src/system_stm32wbxx.c STM32WBxx system source file
@par Hardware and Software environment
- This example runs on STM32WB55xx devices.
- This example has been tested with STMicroelectronics P-NUCLEO-WB55
board and can be easily tailored to any other supported device
and development board.
- P-NUCLEO-WB55 Set-up
- LED2 connected to PB.00 pin
- User push-button connected to pin PC.13 (External line 15 to 10)
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
|
