config: Fix Ender 3 S1 Config (#5771)

Signed-off-by: Rob Casper <myallneedsemail@gmail.com>

1 files changed, 21 insertions, 21 deletions

diff --git a/config/printer-creality-ender3-s1-2021.cfg b/config/printer-creality-ender3-s1-2021.cfg
index bda56e75c..e46ae6def 100644
--- a/config/printer-creality-ender3-s1-2021.cfg
+++ b/config/printer-creality-ender3-s1-2021.cfg
@@ -1,20 +1,20 @@
 # This file contains pin mappings for the stock 2021 Creality Ender 3
-# S1 (and S1 pro). To use this config, check the STM32 Chip on the
-# V2.4S1 Board then during "make menuconfig" select either the
-# STM32F103 with a "28KiB bootloader" or select the STM32F401 with a
-# "64KiB bootloader" and serial (on USART1 PA10/PA9) communication for
-# both depending on the STM32 chip installed on your printer's
-# motherboard.
-
-# If you prefer a direct serial connection, in "make menuconfig"
-# select "Enable extra low-level configuration options" and select
-# Serial (on USART2 PA3/PA2), which is broken out on the 10 pin IDC
-# cable used for the LCD module as follows:
-# 3: Tx, 4: Rx, 9: GND, 10: VCC
+# S1 & S1 Pro. To use this config, check the STM32 Chip on the
+# Mainboard, during "make menuconfig" select accordingly either the
+# STM32F103 with "28KiB bootloader" or the STM32F401 with
+# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
+
+# For a direct serial connection, in "make menuconfig" select
+# "Enable extra low-level configuration options" and  Serial
+# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
+# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
 
 # Flash this firmware by copying "out/klipper.bin" to a SD card and
-# turning on the printer with the card inserted. The firmware
-# filename must changed to "firmware.bin"
+# turning on the printer with the card inserted. The filename
+# must be changed to "firmware.bin"
+
+# With STM32F401, you might need to put "firmware.bin" in a
+# folder on the SD card called "STM32F4_UPDATE" in order to flash.
 
 # See docs/Config_Reference.md for a description of parameters.
 
@@ -37,9 +37,9 @@ enable_pin: !PC3
 microsteps: 16
 rotation_distance: 40
 endstop_pin: !PA6
-position_endstop: -10
-position_max: 241
-position_min: -15
+position_endstop: -8
+position_max: 238
+position_min: -13
 homing_speed: 50
 
 [stepper_z]
@@ -69,7 +69,7 @@ pid_Kp: 23.561
 pid_Ki: 1.208
 pid_Kd: 114.859
 min_temp: 0
-max_temp: 250
+max_temp: 260 # Set to 300 for S1 Pro
 
 [heater_bed]
 heater_pin: PA7
@@ -80,7 +80,7 @@ pid_Kp: 71.867
 pid_Ki: 1.536
 pid_Kd: 840.843
 min_temp: 0
-max_temp: 110
+max_temp: 100 # Set to 110 for S1 Pro
 
 [heater_fan hotend_fan]
 pin: PC0
@@ -111,14 +111,14 @@ stow_on_each_sample: false
 [bed_mesh]
 speed: 120
 mesh_min: 20, 20
-mesh_max: 200, 200
+mesh_max: 200, 197
 probe_count: 4,4
 algorithm: bicubic
 
 [safe_z_home]
 home_xy_position: 147, 154
 speed: 75
-z_hop: 5
+z_hop: 10
 z_hop_speed: 5
 move_to_previous: true